| Commit message (Collapse) | Author | Age |
|
|
|
|
|
|
|
|
| |
This reverts commit 8d7d9cca4390062ccd09ffd9fdb37d1c4eeea9ac.
Now that the necessary infrastructure is really all there
in the tree, we can put this change back in.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When smsc911x uses GPIO as the interrupt controller, and if both are
loaded as modules, we get following error:
"smsc911x: Could not allocate irq resource"
This issue is because of smsc911x using platform_get_resource to get
device tree based irq resource.
commit "9ec36ca (of/irq: do irq resolution in platform_get_irq)" and
commit "7085a7 (drivers: platform: parse IRQ flags from resources)" add
support in platform_get_irq to resolve irq and irq_flags respectively
for both modern device tree and legacy static platform data platforms.
Modify smsc911x driver to use platform_get_irq to pick up irq resource
correctly and use irq_get_trigger_type to get the IRQ trigger flags.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Commit cb6e0b3690f48dff ("net: smc91x: make use of 4th parameter to devm_gpiod_get_index")
caused the following build warning:
drivers/net/ethernet/smsc/smc91x.c:2208:6: warning: unused variable 'res' [-Wunused-variable]
Remove the unused 'res' variable.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since 39b2bbe3d715 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Simplify accordingly.
Moreover use devm_gpiod_get_index_optional for still simpler handling.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The commit breaks the legacy platforms, ie. these not using device-tree,
and setting up the interrupt resources with a flag to activate edge
detection. The issue was found on the zylonite platform.
The reason is that zylonite uses platform resources to pass the interrupt number
and the irq flags (here IORESOURCE_IRQ_HIGHEDGE). It expects the driver to
request the irq with these flags, which in turn setups the irq as high edge
triggered.
After the patch, this was supposed to be taken care of with :
irq_resflags = irqd_get_trigger_type(irq_get_irq_data(ndev->irq));
But irq_resflags is 0 for legacy platforms, while for example in
arch/arm/mach-pxa/zylonite.c, in struct resource smc91x_resources[] the
irq flag is specified. This breaks zylonite because the interrupt is not
setup as triggered, and hardware doesn't provide interrupts.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
I recently did a rework of the smc91x driver and did some build-testing
by compiling hundreds of randconfig kernels. Unfortunately, my script
was wrong and did not actually test the configurations that mattered,
so I introduced stupid typos in almost every file I touched.
I fixed my script now, built all configurations that actually matter
and fixed all the typos, this is the result.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b70661c70830d ("net: smc91x: use run-time configuration on all ARM machines")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The smc91x driver traditionally gets configured at compile-time
for whichever hardware it runs on. This no longer works on
ARM as we continue to move to building all-in-one kernels.
Most ARM configurations with this driver already use run-time
configuration through DT or through platform_data, but a
few have not been converted yet.
I've checked all ARM boards that use this driver in their
legacy board files, and converted the ones that were using
compile-time configuration in smc91x.h to behave like the
other ones and provide the interrupt polarity along with
the MMIO configuration (width, stride) at platform device
creation time.
In particular, these combinations were previously selectable
in Kconfig but in fact broken:
- sa1100 assabet plus pleb
- msm combined with any other armv6/v7 platform
- pxa-idp combined with any non-DMA pxa variant
- LogicPD PXA270 combined with any other pxa
- nomadik combined with any other armv4/v5 platform,
e.g. versatile.
None of these seem critical enough to warrant a backport
to stable, but it would be nice to clean this up for good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
----
I would like the patch to get merged through netdev, after
Robert and/or Linus have verified it on at least some hardware.
There are a few other non-ARM platforms using this driver,
I could do the same patch for those if we want to take
it further.
arch/arm/mach-msm/board-halibut.c | 8 ++++-
arch/arm/mach-msm/board-qsd8x50.c | 8 ++++-
arch/arm/mach-pxa/idp.c | 5 +++
arch/arm/mach-pxa/lpd270.c | 8 ++++-
arch/arm/mach-realview/core.c | 7 ++++
arch/arm/mach-realview/realview_eb.c | 2 +-
arch/arm/mach-sa1100/neponset.c | 6 ++++
arch/arm/mach-sa1100/pleb.c | 7 ++++
drivers/net/ethernet/smsc/smc91x.c | 9 +++--
drivers/net/ethernet/smsc/smc91x.h | 114 ++----------------------------------------------------------
10 files changed, 57 insertions(+), 117 deletions(-)
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The smc91x driver tries to support multiple platforms at compile
time, but they are mutually exclusive at runtime, and not clearly
defined.
Trying to build for CONFIG_SA1100_ASSABET without CONFIG_ASSABET_NEPONSET
results in this link error:
drivers/built-in.o: In function `smc_drv_probe':
:(.text+0x33310c): undefined reference to `neponset_ncr_frob'
since the neponset_ncr_set function is not defined otherwise.
Similarly, building for both CONFIG_SA1100_ASSABET and CONFIG_SA1100_PLEB
results in a different build error:
smsc/smc91x.c: In function 'smc_drv_probe':
smsc/smc91x.c:2299:2: error: implicit declaration of function 'neponset_ncr_set' [-Werror=implicit-function-declaration]
neponset_ncr_set(NCR_ENET_OSC_EN);
^
smsc/smc91x.c:2299:19: error: 'NCR_ENET_OSC_EN' undeclared (first use in this function)
neponset_ncr_set(NCR_ENET_OSC_EN);
^
This is an attempt to fix the call site responsible for both
errors, making sure we call the function exactly when the driver
is actually trying to run on the assabet/neponset machine. With
this patch, I no longer see randconfig build errors in this file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/
|
|
|
|
|
|
| |
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add Atari specific code to the smc91x Ethernet driver. This code is used
on the EtherNAT adapter card for the Atari Falcon extension port.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Tested-by: Christian Steigies <cts@debian.org>
[geert: Sort Kconfig entries, split in hard and soft dependencies]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If GPIOLIB=n the following build errors occur:
drivers/net/ethernet/smsc/smc91x.c: In function 'try_toggle_control_gpio':
drivers/net/ethernet/smsc/smc91x.c:2204:2: error: implicit declaration of function 'devm_gpiod_get_index' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2204:7: warning: assignment makes pointer from integer without a cast [enabled by default]
drivers/net/ethernet/smsc/smc91x.c:2213:2: error: implicit declaration of function 'gpiod_direction_output' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2216:3: error: implicit declaration of function 'devm_gpiod_put' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2222:2: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
Fix this by letting the driver depend on GPIOLIB if OF is selected.
Fixes: 7d2911c4381 ("net: smc91x: Fix gpios for device tree based booting")
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
|
| |\
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into driver-core-next
Remove all .owner fields from platform drivers
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This chip is present on the Nios2 Development Kit 2C35.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add minimal runtime PM support (enable on probe, disable on remove), to
ensure proper operation with a parent device that uses runtime PM.
This is needed on systems where the external bus controller module of
the SoC is contained in a PM domain and/or has a gateable functional
clock. In such cases, before accessing any device connected to the
external bus, the PM domain must be powered up, and/or the functional
clock must be enabled, which is typically handled through runtime PM by
the bus controller driver.
An example of this is the kzm9g development board, where an smsc9220
Ethernet controller is connected to the Bus State Controller (BSC) of a
Renesas sh73a0 SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
With commit be9dad1f9f26604fb ("net: phy: suspend phydev when going
to HALTED"), the PHY device will be put in a low-power mode using
BMCR_PDOWN if the the interface is set down. The smsc911x driver does
a software_reset opening the device driver (ndo_open). In such case,
the PHY must be powered-up before access to any register and before
calling the software_reset function. Otherwise, as the PHY is powered
down the software reset fails and the interface can not be enabled
again.
This patch fixes this scenario that is easy to reproduce setting down
the network interface and setting up again.
$ ifconfig eth0 down
$ ifconfig eth0 up
ifconfig: SIOCSIFFLAGS: Input/output error
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Increased delay in the smsc911x_phy_disable_energy_detect (from 1ms to 2ms).
Dropped delays in the smsc911x_phy_enable_energy_detect (100ms and 1ms).
The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).
I saw problems with soft reset due to wrong udelay timings.
After I fixed udelay, I measured the time needed to bring integrated PHY
from power-down to operational mode (the time beetween clearing EDPWRDOWN
bit and soft reset complete event). I got 1ms (measured using ktime_get).
The value is equal to the current value (1ms) used in the
smsc911x_phy_disable_energy_detect. It is near the upper bound and in order
to avoid rare soft reset faults it is doubled (2ms).
I don't know official timing for bringing up integrated PHY as specs doesn't
clarify this (or may be I didn't found).
It looks safe to drop delays before and after setting EDPWRDOWN bit
(enable PHY power-down mode). I didn't saw any regressions with the patch.
The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).
It is possible that PHY could enter power-down mode (ENERGYON clear),
between ENERGYON bit check in smsc911x_phy_disable_energy_detect and SRST
bit set in smsc911x_soft_reset. This could happen, for example, if someone
disconnect ethernet cable between the checks. The PHY in a power-down mode
would prevent the MAC portion of chip to be software reseted.
Initially found by code review, confirmed later using test case.
This is low probability issue, and in order to reproduce it you have to
run the script:
while true; do
ifconfig eth0 down
ifconfig eth0 up || break
done
While the script is running you have to plug/unplug ethernet cable many
times (using gpio controlled ethernet switch, for example) until get:
[ 4516.477783] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4516.512207] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce006000, IRQ: 336
[ 4516.524658] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4516.559082] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce006000, IRQ: 336
[ 4516.571990] ADDRCONF(NETDEV_UP): eth0: link is not ready
ifconfig: SIOCSIFFLAGS: Input/output error
The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/ /
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The SMC91x is written to explicitly look up the IRQ resource
from the platform device and extract the IRQ and flags, however
the platform_get_irq() does additional things, like call
of_irq_get() in the device tree case, which will translate
the IRQ using the irqdomain and defer the probe if the
IRQ host cannot be found.
As we're not looking up the resource, this will not retrieve
the IRQ flags, but that is better done using
irqd_get_trigger_type(), as the trigger is what the driver
wants to modify. We take care to preserve the semantics that
will make the trigger type provided from the resource
override any local specifier.
Tested on the Nomadik NHK15 which has its SMC91x IRQ line
connected to a STMPE2401 GPIO expander on I2C.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.
Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.
And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
There is no need to call ether_setup after alloc_ethdev since it was
already called there.
Follow commits c706471b2601 ("net: axienet: remove unnecessary
ether_setup after alloc_etherdev") and 3c87dcbfb36c ("net: ll_temac:
Remove unnecessary ether_setup after alloc_etherdev") and fix the
pattern in all remaining ethernet drivers.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|/
|
|
|
|
|
|
| |
spin_is_locked() always return false in uniprocessor configuration and therefore it
would be advise to repalce with WARN_ON_SMP().
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
| |
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
As smsc driver supports carrier detection, it should unset NOCARRIER
flag only after carrier state determination. By default that flag
is off so driver should set it before starting auto-negotiation
Signed-off-by: Balakumaran <Balakumaran.Kannan@ap.sony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Redefine some macros that were conditioned upon SMC_DEBUG level.
By allowing compiler to verify parameters used by these macros
unconditionally, we can flag compilation failures.
Compiler will still optimize out the unused code path depending on
SMC_DEBUG, so this is a net gain.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When SMC_DEBUG >= 2, we hit the following compilation error:
drivers/net/ethernet/smsc/smc91x.c:85:0:
drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_findirq’:
drivers/net/ethernet/smsc/smc91x.c:1784:9: error: ‘dev’ undeclared (first use in this function)
DBG(2, dev, "%s: %s\n", CARDNAME, __func__);
^
Fix it by passing in the appropriate netdev pointer.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
The ioaddr local variable is assigned to but never used in the
smc911x_rx_dma_irq() function, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
| |
Having the kernel to print:
"smsc911x: Driver version 2008-10-21" on every boot is not very useful, so
remove the print of the driver version.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
With debug enabled we get the following message:
smsc911x smsc911x (unregistered net_device): couldn't get clock -2
As the device has not been registered at this point, it is better to use
dev_dbg() instead of netdev_dbg().
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
Replace dev_kfree_skb with dev_consume_skb_any in smsc911x_hard_xmit
which can be called in hard irq and other contexts. smsc911x_hard_xmit
always transmits and consumes the specified skb.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Replace dev_kfree_skb with dev_consume_skb_any in
smc_hardware_send_pkt that can be called in hard irq and other
contexts, and handles successfully transmitted packets.
Replace dev_kfree_skb with dev_kfree_skb_any in smc_hard_start_xmit which
can be called in hard irq and other contexts, and only frees skbs
when dropping them.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
|
|
|
|
|
| |
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since passing the clock is not mandatory, change the warning message to debug,
so that we avoid getting the following clock failure message on every boot:
smsc911x: Driver version 2008-10-21
smsc911x smsc911x (unregistered net_device): couldn't get clock -2
libphy: smsc911x-mdio: probed
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If used 64 bit compiler GCC warns that:
drivers/net/ethernet/smsc/smc91x.c:1897:7:
warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
This patch fixes this by changing typecast from "unsigned int" to "unsigned long"
CC: "David S. Miller" <davem@davemloft.net>
CC: Jingoo Han <jg1.han@samsung.com>
CC: netdev@vger.kernel.org
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2;
@@
pci_enable_wake(e1,
- 0
+ PCI_D0
,e2)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Commit 89ce376c6bdc (drivers/net: Use of_match_ptr() macro in smc91x.c)
added minimal device tree support to smc91x, but it's not working on
many platforms because of the lack of some key configuration bits.
Fix the issue by parsing the necessary configuration like the
smc911x driver is doing. As most smc91x users seem to use 16-bit
access, let's default to that if no reg-io-width is specified.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Dimitris Michailidis <dm@chelsio.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Santiago Leon <santil@linux.vnet.ibm.com>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Olof Johansson <olof@lixom.net>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Nicolas Pitre <nico@fluxnic.net>
CC: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
After commit e9e4ea74f06635f2ffc1dffe5ef40c854faa0a90
"net: smc91x: dont't use SMC_outw for fixing up halfword-aligned data"
The Versatile SMSC LAN91C111 is crashing like this:
------------[ cut here ]------------
kernel BUG at /home/linus/linux/drivers/net/ethernet/smsc/smc91x.c:599!
Internal error: Oops - BUG: 0 [#1] ARM
Modules linked in:
CPU: 0 PID: 43 Comm: udhcpc Not tainted 3.13.0-rc1+ #24
task: c6ccfaa0 ti: c6cd0000 task.ti: c6cd0000
PC is at smc_hardware_send_pkt+0x198/0x22c
LR is at smc_hardware_send_pkt+0x24/0x22c
pc : [<c01be324>] lr : [<c01be1b0>] psr: 20000013
sp : c6cd1d08 ip : 00000001 fp : 00000000
r10: c02adb08 r9 : 00000000 r8 : c6ced802
r7 : c786fba0 r6 : 00000146 r5 : c8800000 r4 : c78d6000
r3 : 0000000f r2 : 00000146 r1 : 00000000 r0 : 00000031
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 0005317f Table: 06cf4000 DAC: 00000015
Process udhcpc (pid: 43, stack limit = 0xc6cd01c0)
Stack: (0xc6cd1d08 to 0xc6cd2000)
1d00: 00000010 c8800000 c78d6000 c786fba0 c78d6000 c01be868
1d20: c01be7a4 00004000 00000000 c786fba0 c6c12b80 c0208554 000004d0 c780fc60
1d40: 00000220 c01fb734 00000000 00000000 00000000 c6c9a440 c6c12b80 c78d6000
1d60: c786fba0 c6c9a440 00000000 c021d1d8 00000000 00000000 c6c12b80 c78d6000
1d80: c786fba0 00000001 c6c9a440 c02087f8 c6c9a4a0 00080008 00000000 00000000
1da0: c78d6000 c786fba0 c78d6000 00000138 00000000 00000000 00000000 00000000
1dc0: 00000000 c027ba74 00000138 00000138 00000001 00000010 c6cedc00 00000000
1de0: 00000008 c7404400 c6cd1eec c6cd1f14 c067a73c c065c0b8 00000000 c067a740
1e00: 01ffffff 002040d0 00000000 00000000 00000000 00000000 00000000 ffffffff
1e20: 43004400 00110022 c6cdef20 c027ae8c c6ccfaa0 be82d65c 00000014 be82d3cc
1e40: 00000000 00000000 00000000 c01f2870 00000000 00000000 00000000 c6cd1e88
1e60: c6ccfaa0 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1e80: 00000000 00000000 00000031 c7802310 c7802300 00000138 c7404400 c0771da0
1ea0: 00000000 c6cd1eec c7800340 00000138 be82d65c 00000014 be82d3cc c6cd1f08
1ec0: 00000014 00000000 c7404400 c7404400 00000138 c01f4628 c78d6000 00000000
1ee0: 00000000 be82d3cc 00000138 c6cd1f08 00000014 c6cd1ee4 00000001 00000000
1f00: 00000000 00000000 00080011 00000002 06000000 ffffffff 0000ffff 00000002
1f20: 06000000 ffffffff 0000ffff c00928c8 c065c520 c6cd1f58 00000003 c009299c
1f40: 00000003 c065c520 c7404400 00000000 c7404400 c01f2218 c78106b0 c7441cb0
1f60: 00000000 00000006 c06799fc 00000000 00000000 00000006 00000000 c01f3ee0
1f80: 00000000 00000000 be82d678 be82d65c 00000014 00000001 00000122 c00139c8
1fa0: c6cd0000 c0013840 be82d65c 00000014 00000006 be82d3cc 00000138 00000000
1fc0: be82d65c 00000014 00000001 00000122 00000000 00000000 00018cb1 00000000
1fe0: 00003801 be82d3a8 0003a0c7 b6e9af08 60000010 00000006 00000000 00000000
[<c01be324>] (smc_hardware_send_pkt+0x198/0x22c) from [<c01be868>] (smc_hard_start_xmit+0xc4/0x1e8)
[<c01be868>] (smc_hard_start_xmit+0xc4/0x1e8) from [<c0208554>] (dev_hard_start_xmit+0x460/0x4cc)
[<c0208554>] (dev_hard_start_xmit+0x460/0x4cc) from [<c021d1d8>] (sch_direct_xmit+0x94/0x18c)
[<c021d1d8>] (sch_direct_xmit+0x94/0x18c) from [<c02087f8>] (dev_queue_xmit+0x238/0x42c)
[<c02087f8>] (dev_queue_xmit+0x238/0x42c) from [<c027ba74>] (packet_sendmsg+0xbe8/0xd28)
[<c027ba74>] (packet_sendmsg+0xbe8/0xd28) from [<c01f2870>] (sock_sendmsg+0x84/0xa8)
[<c01f2870>] (sock_sendmsg+0x84/0xa8) from [<c01f4628>] (SyS_sendto+0xb8/0xdc)
[<c01f4628>] (SyS_sendto+0xb8/0xdc) from [<c0013840>] (ret_fast_syscall+0x0/0x2c)
Code: e3130002 1a000001 e3130001 0affffcd (e7f001f2)
---[ end trace 81104fe70e8da7fe ]---
Kernel panic - not syncing: Fatal exception in interrupt
This is because the macro operations in smc91x.h defined
for Versatile are missing SMC_outsw() as used in this
commit.
The Versatile needs and uses the same accessors as the other
platforms in the first if(...) clause, just switch it to using
that and we have one problem less to worry about.
This includes a hunk of a patch from Will Deacon fixin
the other 32bit platforms as well: Innokom, Ramses, PXA,
PCM027.
Checkpatch complains about spacing, but I have opted to
follow the style of this .h-file.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
This reverts commit b268daffdcb9762ad9aa3898096570a9dd92aa9b.
I applied the wrong version of this patch, the proper version
is coming up next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|