aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/freescale/fec_main.c
Commit message (Collapse)AuthorAge
* net: fec: Fix RGMII-ID modeMarkus Pargmann2015-04-30
| | | | | | | | | | | RGMII-ID uses an internal delay within the transmitter or receiver. This feature is phy specific. The rest of the communication is normal RGMII. So the fec driver has to check for all RGMII modes, not only 'PHY_INTERFACE_MODE_RGMII'. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: setup right value for mdio hold timeUwe Kleine-König2015-03-29
| | | | | | | | | | | | | The FEC modules used on i.MX28 and newer have a register to tune the MDIO output hold time that should be at least 10 ns. Up to now this value was not explicitly set and so resulted in less hold time if the fec clock was faster than 100 MHz. This was noticed on an i.MX28 machine that uses an input clock of ~150 Mhz which resulted in unreliable communication with a Marvell switch. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* Revert "net: fec: fix the warning found by dma debug"Fabio Estevam2015-03-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 2b995f63987013bacde99168218f9c7b252bdcf1. Панов Андрей reported the following regression: "Commit 2b995f63987013bacde99168218f9c7b252bdcf1 in 4.0.0-rc3 introduces a nasty bug in transmit, corrupting packets. To reproduce: $ dd if=/dev/zero of=zeros bs=1M count=20 $ md5sum -b zeros 8f4e33f3dc3e414ff94e5fb6905cba8c *zeros This checksum is correct. Copy file "zeros" to another host with NFS, and it gets corrupted, checksum is changed. File should be big, small amounts of transmit isn't affected. I use an i.MX6 Quad board. If this commit is reverted, all works fine." Reported-by: Панов Андрей <rockford@yandex.ru> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: fix receive VLAN CTAG HW acceleration issueNimrod Andy2015-03-10
| | | | | | | | | | | | | | | | The current driver support receive VLAN CTAG HW acceleration feature (NETIF_F_HW_VLAN_CTAG_RX) through software simulation. There calls the api .skb_copy_to_linear_data_offset() to skip the VLAN tag, but there have overlap between the two memory data point range. The patch just fix the issue. V2: Michael Grzeschik suggest to use memmove() instead of skb_copy_to_linear_data_offset(). Reported-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Fixes: 1b7bde6d659d ("net: fec: implement rx_copybreak to improve rx performance") Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: fix unbalanced clk disable on driver unbindStefan Agner2015-03-05
| | | | | | | | | | | | | | | | | When the driver is removed (e.g. using unbind through sysfs), the clocks get disabled twice, once on fec_enet_close and once on fec_drv_remove. Since the clocks are enabled only once, this leads to a warning: WARNING: CPU: 0 PID: 402 at drivers/clk/clk.c:992 clk_core_disable+0x64/0x68() Remove the call to fec_enet_clk_enable in fec_drv_remove to balance the clock enable/disable calls again. This has been introduce by e8fcfcd5684a ("net: fec: optimize the clock management to save power"). Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: fix rcv is not last issue when do suspend/resume testFugang Duan2015-03-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When do suspend/resume stress test, some log shows "rcv is not +last". The issue is that enet suspend will disable phy clock, phy link down, after resume back, enet MAC redo initial and ready to tx/rx packet, but phy still is not ready which is doing auto-negotiation. When phy link is not up, don't schdule napi soft irq. [Peter] It has fixed kernel panic after long time suspend/resume test with nfs rootfs. [ 8864.429458] fec 2188000.ethernet eth0: rcv is not +last [ 8864.434799] fec 2188000.ethernet eth0: rcv is not +last [ 8864.440088] fec 2188000.ethernet eth0: rcv is not +last [ 8864.445424] fec 2188000.ethernet eth0: rcv is not +last [ 8864.450782] fec 2188000.ethernet eth0: rcv is not +last [ 8864.456111] Unable to handle kernel NULL pointer dereference at virtual address 00000000 [ 8864.464225] pgd = 80004000 [ 8864.466997] [00000000] *pgd=00000000 [ 8864.470627] Internal error: Oops: 17 [#1] SMP ARM [ 8864.475353] Modules linked in: evbug [ 8864.479006] CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.0.0-rc1-00044-g7a2a1d2 #234 [ 8864.486854] Hardware name: Freescale i.MX6 SoloX (Device Tree) [ 8864.492709] task: be069380 ti: be07a000 task.ti: be07a000 [ 8864.498137] PC is at memcpy+0x80/0x330 [ 8864.501919] LR is at gro_pull_from_frag0+0x34/0xa8 [ 8864.506735] pc : [<802bb080>] lr : [<8057c204>] psr: 00000113 [ 8864.506735] sp : be07bbd4 ip : 00000010 fp : be07bc0c [ 8864.518235] r10: 0000000e r9 : 00000000 r8 : 809c7754 [ 8864.523479] r7 : 809c7754 r6 : bb43c040 r5 : bd280cc0 r4 : 00000012 [ 8864.530025] r3 : 00000804 r2 : fffffff2 r1 : 00000000 r0 : bb43b83c [ 8864.536575] Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel [ 8864.543904] Control: 10c5387d Table: bd14c04a DAC: 00000015 [ 8864.549669] Process ksoftirqd/0 (pid: 3, stack limit = 0xbe07a210) [ 8864.555869] Stack: (0xbe07bbd4 to 0xbe07c000) [ 8864.560250] bbc0: bd280cc0 bb43c040 809c7754 [ 8864.568455] bbe0: 809c7754 bb43b83c 00000012 8057c204 00000000 bd280cc0 bd8a0718 00000003 [ 8864.576658] bc00: be07bc5c be07bc10 8057ebf0 8057c1dc 00000000 00000000 8057ecc4 bef59760 [ 8864.584863] bc20: 00000002 bd8a0000 be07bc64 809c7754 00000000 bd8a0718 bd280cc0 bd8a0000 [ 8864.593066] bc40: 00000000 0000001c 00000000 bd8a0000 be07bc74 be07bc60 8057f148 8057eb90 [ 8864.601268] bc60: bf0810a0 00000000 be07bcf4 be07bc78 8044e7b4 8057f12c 00000000 8007df6c [ 8864.609470] bc80: bd8a0718 00000040 00000000 bd280a80 00000002 00000019 bd8a0600 bd8a1214 [ 8864.617672] bca0: bd8a0690 bf0810a0 00000000 00000000 bd8a1000 00000000 00000027 bd280cc0 [ 8864.625874] bcc0: 80062708 800625cc 000943db bd8a0718 00000001 000d1166 00000040 be7c1ec0 [ 8864.634077] bce0: 0000012c be07bd00 be07bd3c be07bcf8 8057fc98 8044e3ac 809c2ec0 3ddff000 [ 8864.642280] bd00: be07bd00 be07bd00 be07bd08 be07bd08 00000000 00000020 809c608c 00000003 [ 8864.650481] bd20: 809c6080 40000001 809c6088 00200100 be07bd84 be07bd40 8002e690 8057fac8 [ 8864.658684] bd40: be07bd64 be07bd50 00000001 04208040 000d1165 0000000a be07bd84 809c0d7c [ 8864.666885] bd60: 00000000 809c6af8 00000000 00000001 be008000 00000000 be07bd9c be07bd88 [ 8864.675087] bd80: 8002eb64 8002e564 00000125 809c0d7c be07bdc4 be07bda0 8006f100 8002eaac [ 8864.683291] bda0: c080e10c be07bde8 809c6c6c c080e100 00000002 00000000 be07bde4 be07bdc8 [ 8864.691492] bdc0: 800087a0 8006f098 806f2934 20000013 ffffffff be07be1c be07be44 be07bde8 [ 8864.699695] bde0: 800133a4 80008784 00000001 00000001 00000000 00000000 be7c1680 00000000 [ 8864.707896] be00: be0cfe00 bd93eb40 00000002 00000000 00000000 be07be44 be07be00 be07be30 [ 8864.716098] be20: 8006278c 806f2934 20000013 ffffffff be069380 be7c1680 be07be7c be07be48 [ 8864.724300] be40: 80049cfc 806f2910 00000001 00000000 80049cb4 00000000 be07be7c be7c1680 [ 8864.732502] be60: be3289c0 be069380 bd23b600 be0cfe00 be07bebc be07be80 806ed614 80049c68 [ 8864.740706] be80: be07a000 0000020a 809c608c 00000003 00000001 8002e858 be07a000 be035740 [ 8864.748907] bea0: 00000000 00000001 809d4598 00000000 be07bed4 be07bec0 806edd0c 806ed440 [ 8864.757110] bec0: be07a000 be07a000 be07bee4 be07bed8 806edd68 806edcf0 be07bef4 be07bee8 [ 8864.765311] bee0: 8002e860 806edd34 be07bf24 be07bef8 800494b0 8002e828 be069380 00000000 [ 8864.773512] bf00: be035780 be035740 8004938c 00000000 00000000 00000000 be07bfac be07bf28 [ 8864.781715] bf20: 80045928 80049398 be07bf44 00000001 00000000 be035740 00000000 00030003 [ 8864.789917] bf40: dead4ead ffffffff ffffffff 80a2716c 80b59b00 00000000 8088c954 be07bf5c [ 8864.798120] bf60: be07bf5c 00000000 00000000 dead4ead ffffffff ffffffff 80a2716c 00000000 [ 8864.806320] bf80: 00000000 8088c954 be07bf88 be07bf88 be035780 8004584c 00000000 00000000 [ 8864.814523] bfa0: 00000000 be07bfb0 8000ed10 80045858 00000000 00000000 00000000 00000000 [ 8864.822723] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 8864.830925] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 5ffbb5f7 f9fcf5e7 [ 8864.839115] Backtrace: [ 8864.841631] [<8057c1d0>] (gro_pull_from_frag0) from [<8057ebf0>] (dev_gro_receive+0x6c/0x3f8) [ 8864.850173] r6:00000003 r5:bd8a0718 r4:bd280cc0 r3:00000000 [ 8864.855958] [<8057eb84>] (dev_gro_receive) from [<8057f148>] (napi_gro_receive+0x28/0xac) [ 8864.864152] r10:bd8a0000 r9:00000000 r8:0000001c r7:00000000 r6:bd8a0000 r5:bd280cc0 [ 8864.872115] r4:bd8a0718 [ 8864.874713] [<8057f120>] (napi_gro_receive) from [<8044e7b4>] (fec_enet_rx_napi+0x414/0xc74) [ 8864.883167] r5:00000000 r4:bf0810a0 [ 8864.886823] [<8044e3a0>] (fec_enet_rx_napi) from [<8057fc98>] (net_rx_action+0x1dc/0x2ec) [ 8864.895016] r10:be07bd00 r9:0000012c r8:be7c1ec0 r7:00000040 r6:000d1166 r5:00000001 [ 8864.902982] r4:bd8a0718 [ 8864.905570] [<8057fabc>] (net_rx_action) from [<8002e690>] (__do_softirq+0x138/0x2c4) [ 8864.913417] r10:00200100 r9:809c6088 r8:40000001 r7:809c6080 r6:00000003 r5:809c608c [ 8864.921382] r4:00000020 [ 8864.923966] [<8002e558>] (__do_softirq) from [<8002eb64>] (irq_exit+0xc4/0x138) [ 8864.931289] r10:00000000 r9:be008000 r8:00000001 r7:00000000 r6:809c6af8 r5:00000000 [ 8864.939252] r4:809c0d7c [ 8864.941841] [<8002eaa0>] (irq_exit) from [<8006f100>] (__handle_domain_irq+0x74/0xe8) [ 8864.949688] r4:809c0d7c r3:00000125 [ 8864.953342] [<8006f08c>] (__handle_domain_irq) from [<800087a0>] (gic_handle_irq+0x28/0x68) [ 8864.961707] r9:00000000 r8:00000002 r7:c080e100 r6:809c6c6c r5:be07bde8 r4:c080e10c [ 8864.969597] [<80008778>] (gic_handle_irq) from [<800133a4>] (__irq_svc+0x44/0x5c) [ 8864.977097] Exception stack(0xbe07bde8 to 0xbe07be30) [ 8864.982173] bde0: 00000001 00000001 00000000 00000000 be7c1680 00000000 [ 8864.990377] be00: be0cfe00 bd93eb40 00000002 00000000 00000000 be07be44 be07be00 be07be30 [ 8864.998573] be20: 8006278c 806f2934 20000013 ffffffff [ 8865.003638] r7:be07be1c r6:ffffffff r5:20000013 r4:806f2934 [ 8865.009447] [<806f2904>] (_raw_spin_unlock_irq) from [<80049cfc>] (finish_task_switch+0xa0/0x160) [ 8865.018334] r4:be7c1680 r3:be069380 [ 8865.021993] [<80049c5c>] (finish_task_switch) from [<806ed614>] (__schedule+0x1e0/0x5dc) [ 8865.030098] r8:be0cfe00 r7:bd23b600 r6:be069380 r5:be3289c0 r4:be7c1680 [ 8865.036942] [<806ed434>] (__schedule) from [<806edd0c>] (preempt_schedule_common+0x28/0x44) [ 8865.045307] r9:00000000 r8:809d4598 r7:00000001 r6:00000000 r5:be035740 r4:be07a000 [ 8865.053197] [<806edce4>] (preempt_schedule_common) from [<806edd68>] (_cond_resched+0x40/0x48) [ 8865.061822] r4:be07a000 r3:be07a000 [ 8865.065472] [<806edd28>] (_cond_resched) from [<8002e860>] (run_ksoftirqd+0x44/0x64) [ 8865.073252] [<8002e81c>] (run_ksoftirqd) from [<800494b0>] (smpboot_thread_fn+0x124/0x190) [ 8865.081550] [<8004938c>] (smpboot_thread_fn) from [<80045928>] (kthread+0xdc/0xf8) [ 8865.089133] r10:00000000 r9:00000000 r8:00000000 r7:8004938c r6:be035740 r5:be035780 [ 8865.097097] r4:00000000 r3:be069380 [ 8865.100752] [<8004584c>] (kthread) from [<8000ed10>] (ret_from_fork+0x14/0x24) [ 8865.107990] r7:00000000 r6:00000000 r5:8004584c r4:be035780 [ 8865.113767] Code: e320f000 e4913004 e4914004 e4915004 (e4916004) [ 8865.120006] ---[ end trace b0a4c6bd499288ca ]--- [ 8865.124697] Kernel panic - not syncing: Fatal exception in interrupt [ 8865.131084] ---[ end Kernel panic - not syncing: Fatal exception in interrupt Cc: [v3.19+] stable@vger.kernel.org Tested-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: Delete unnecessary checks before the function call "kfree"Markus Elfring2015-02-05
| | | | | | | | | | The kfree() function tests whether its argument is NULL and then returns immediately. Thus the test around the call is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: fix the warning found by dma debugNimrod Andy2015-01-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable kernel config "CONFIG_HAVE_DMA_API_DEBUG", FEC have kernel warning: [ 6.650444] fec 2188000.ethernet: DMA-API: device driver tries to free DMA memory it has not allocated [ 6.664289] Modules linked in: [ 6.667378] CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 3.19.0-rc4-00688-g8834016-dirty #150 [ 6.675841] Hardware name: Freescale i.MX6 SoloX (Device Tree) [ 6.681698] Backtrace: [ 6.684189] [<80011e3c>] (dump_backtrace) from [<80011fdc>] (show_stack+0x18/0x1c) [ 6.691789] r6:80890154 r5:00000000 r4:00000000 r3:00000000 [ 6.697533] [<80011fc4>] (show_stack) from [<806d2d88>] (dump_stack+0x80/0x9c) [ 6.704799] [<806d2d08>] (dump_stack) from [<8002a4e4>] (warn_slowpath_common+0x7c/0xb4) [ 6.712917] r5:00000445 r4:00000000 [ 6.716544] [<8002a468>] (warn_slowpath_common) from [<8002a5c0>] (warn_slowpath_fmt+0x38/0x40) [ 6.725265] r8:809a2ee8 r7:00000000 r6:00000000 r5:00000000 r4:00000042 [ 6.732087] [<8002a58c>] (warn_slowpath_fmt) from [<802d6268>] (check_unmap+0x86c/0x98c) [ 6.740202] r3:808c79bc r2:8089060c [ 6.743826] [<802d59fc>] (check_unmap) from [<802d65e4>] (debug_dma_unmap_page+0x80/0x88) [ 6.752029] r10:00000000 r9:00000000 r8:00000000 r7:00000001 r6:be12a410 r5:00000000 [ 6.759967] r4:00000042 [ 6.762538] [<802d6564>] (debug_dma_unmap_page) from [<80440248>] (fec_enet_rx_napi+0x7ec/0xb9c) [ 6.771345] r7:00000400 r6:be3e4000 r5:bf08fa20 r4:be036000 [ 6.777094] [<8043fa5c>] (fec_enet_rx_napi) from [<8056ae24>] (net_rx_action+0x134/0x324) [ 6.785297] r10:be089e60 r9:80998180 r8:ffff8d68 r7:0000012c r6:00000040 r5:00000001 [ 6.793239] r4:be036718 [ 6.795801] [<8056acf0>] (net_rx_action) from [<8002db24>] (__do_softirq+0x138/0x2d0) [ 6.803655] r10:00000003 r9:00000003 r8:80996378 r7:8099c080 r6:00000100 r5:8099c08c [ 6.811593] r4:00000000 [ 6.814157] [<8002d9ec>] (__do_softirq) from [<8002dd00>] (run_ksoftirqd+0x44/0x5c) [ 6.821836] r10:00000000 r9:00000000 r8:809b133c r7:00000000 r6:00000001 r5:00000000 [ 6.829775] r4:be027e80 [ 6.832346] [<8002dcbc>] (run_ksoftirqd) from [<80048290>] (smpboot_thread_fn+0x154/0x1c4) [ 6.840649] [<8004813c>] (smpboot_thread_fn) from [<80044780>] (kthread+0xdc/0xf8) [ 6.848224] r10:00000000 r8:00000000 r7:8004813c r6:be027e80 r5:be027ec0 r4:00000000 [ 6.856179] [<800446a4>] (kthread) from [<8000ebc8>] (ret_from_fork+0x14/0x2c) [ 6.863425] r7:00000000 r6:00000000 r5:800446a4 r4:be027ec0 [ 6.869156] ---[ end trace 861cf914d2461a8b ]--- There have one bug in .fec_enet_tx_queue() function to unmap the DMA memory: For SG or TSO, get one buffer descriptor and then unmap the related DMA memory, and then get the next buffer descriptor, loop to while() to check "TX_READY". If "TX_READY" bit still __IS__ existed in the BD (The next fraglist or next TSO packet is not transmited complitely), exit the current clean work. When the next work is triggered, it still repeat above step with the same BD. The potential issue is that unmap the same DMA memory for multiple times. The patch fix the clean work for SG and TSO packet. Reported-by: Anand Moon <moon.linux@yahoo.com> Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2015-01-15
|\ | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/xen-netfront.c Minor overlapping changes in xen-netfront.c, mostly to do with some buffer management changes alongside the split of stats into TX and RX. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: fec: fix MDIO bus assignement for dual fec SoC'sStefan Agner2015-01-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On i.MX28, the MDIO bus is shared between the two FEC instances. The driver makes sure that the second FEC uses the MDIO bus of the first FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set. However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC has its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC is not an option since other logic, triggered by this quirk, is still needed. Furthermore, there are board designs which use the same MDIO bus for both PHY's even though the second bus would be available on the SoC side. Such layout are popular since it saves pins on SoC side. Due to the above quirk, those boards currently do work fine. The boards in the mainline tree with such a layout are: - Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts) - Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts) This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which makes sure that the MDIO bus of the first FEC is used in any case. However, the boards above do have a SoC with a MDIO bus for each FEC instance. But the PHY's are not connected in a 1:1 configuration. A proper device tree description is needed to allow the driver to figure out where to find its PHY. This patch fixes that shortcoming by adding a MDIO bus child node to the first FEC instance, along with the two PHY's on that bus, and making use of the phy-handle property to add a reference to the PHY's. Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: fec: fix NULL pointer dereference in fec_enet_timeout_workHubert Feurstein2015-01-08
| | | | | | | | | | | | | | | | | | This patch initialises the fep->netdev pointer. This pointer was not initialised at all, but is used in fec_enet_timeout_work and in some error paths. Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: fec: add Wake-on-LAN supportNimrod Andy2014-12-31
|/ | | | | | | | | | | | | | | | Support for Wake-on-LAN using Magic Packet. ENET IP supports sleep mode in low power status, when system enter suspend status, Magic packet can wake up system even if all SOC clocks are gate. The patch doing below things: - flagging the device as a wakeup source for the system, as well as its Wake-on-LAN interrupt - prepare the hardware for entering WoL mode - add standard ethtool WOL interface - enable the ENET interrupt to wake us Tested on i.MX6q/dl sabresd, sabreauto boards, i.MX6SX arm2 boards. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: Fix NAPI raceNimrod Andy2014-12-16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Do camera capture test on i.MX6q sabresd board, and save the capture data to nfs rootfs. The command is: gst-launch-1.0 -e imxv4l2src device=/dev/video1 num-buffers=2592000 ! tee name=t ! queue ! imxv4l2sink sync=false t. ! queue ! vpuenc ! queue ! mux. pulsesrc num-buffers=3720937 blocksize=4096 ! 'audio/x-raw, rate=44100, channels=2' ! queue ! imxmp3enc ! mpegaudioparse ! queue ! mux. qtmux name=mux ! filesink location=video_recording_long.mov After about 10 hours running, there have net watchdog timeout kernel dump: ... WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:264 dev_watchdog+0x2b4/0x2d8() NETDEV WATCHDOG: eth0 (fec): transmit queue 0 timed out CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.24-01051-gdb840b7 #440 [<80014e6c>] (unwind_backtrace) from [<800118ac>] (show_stack+0x10/0x14) [<800118ac>] (show_stack) from [<806ae3f0>] (dump_stack+0x78/0xc0) [<806ae3f0>] (dump_stack) from [<8002b504>] (warn_slowpath_common+0x68/0x8c) [<8002b504>] (warn_slowpath_common) from [<8002b558>] (warn_slowpath_fmt+0x30/0x40) [<8002b558>] (warn_slowpath_fmt) from [<8055e0d4>] (dev_watchdog+0x2b4/0x2d8) [<8055e0d4>] (dev_watchdog) from [<800352d8>] (call_timer_fn.isra.33+0x24/0x8c) [<800352d8>] (call_timer_fn.isra.33) from [<800354c4>] (run_timer_softirq+0x184/0x220) [<800354c4>] (run_timer_softirq) from [<8002f420>] (__do_softirq+0xc0/0x22c) [<8002f420>] (__do_softirq) from [<8002f804>] (irq_exit+0xa8/0xf4) [<8002f804>] (irq_exit) from [<8000ee5c>] (handle_IRQ+0x54/0xb4) [<8000ee5c>] (handle_IRQ) from [<80008598>] (gic_handle_irq+0x28/0x5c) [<80008598>] (gic_handle_irq) from [<800123c0>] (__irq_svc+0x40/0x74) Exception stack(0x80d27f18 to 0x80d27f60) 7f00: 80d27f60 0000014c 7f20: 8858c60e 0000004d 884e4540 0000004d ab7250d0 80d34348 00000000 00000000 7f40: 00000001 00000000 00000017 80d27f60 800702a4 80476e6c 600f0013 ffffffff [<800123c0>] (__irq_svc) from [<80476e6c>] (cpuidle_enter_state+0x50/0xe0) [<80476e6c>] (cpuidle_enter_state) from [<80476fa8>] (cpuidle_idle_call+0xac/0x154) [<80476fa8>] (cpuidle_idle_call) from [<8000f174>] (arch_cpu_idle+0x8/0x44) [<8000f174>] (arch_cpu_idle) from [<80064c54>] (cpu_startup_entry+0x100/0x158) [<80064c54>] (cpu_startup_entry) from [<80cd8a9c>] (start_kernel+0x304/0x368) ---[ end trace 09ebd32fb032f86d ]--- ... There might have a race in napi_schedule(), leaving interrupts disabled forever. After these patch, the case still work more than 40 hours running. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge tag 'driver-core-3.19-rc1' of ↵Linus Torvalds2014-12-14
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core update from Greg KH: "Here's the set of driver core patches for 3.19-rc1. They are dominated by the removal of the .owner field in platform drivers. They touch a lot of files, but they are "simple" changes, just removing a line in a structure. Other than that, a few minor driver core and debugfs changes. There are some ath9k patches coming in through this tree that have been acked by the wireless maintainers as they relied on the debugfs changes. Everything has been in linux-next for a while" * tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits) Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries" fs: debugfs: add forward declaration for struct device type firmware class: Deletion of an unnecessary check before the function call "vunmap" firmware loader: fix hung task warning dump devcoredump: provide a one-way disable function device: Add dev_<level>_once variants ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries ath: use seq_file api for ath9k debugfs files debugfs: add helper function to create device related seq_file drivers/base: cacheinfo: remove noisy error boot message Revert "core: platform: add warning if driver has no owner" drivers: base: support cpu cache information interface to userspace via sysfs drivers: base: add cpu_device_create to support per-cpu devices topology: replace custom attribute macros with standard DEVICE_ATTR* cpumask: factor out show_cpumap into separate helper function driver core: Fix unbalanced device reference in drivers_probe driver core: fix race with userland in device_add() sysfs/kernfs: make read requests on pre-alloc files use the buffer. sysfs/kernfs: allow attributes to request write buffer be pre-allocated. fs: sysfs: return EGBIG on write if offset is larger than file size ...
| * Merge branch 'platform/remove_owner' of ↵Greg Kroah-Hartman2014-11-03
| |\ | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into driver-core-next Remove all .owner fields from platform drivers
| | * net: ethernet: freescale: drop owner assignment from platform_driversWolfram Sang2014-10-20
| | | | | | | | | | | | | | | | | | | | | A platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* | | net: fec: only enable mdio interrupt before phy device link upNimrod Andy2014-12-10
| | | | | | | | | | | | | | | | | | | | | | | | Before phy device link up, we only enable FEC mdio interrupt, which is more reasonable. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: fec: clear all interrupt events to support i.MX6SXNimrod Andy2014-12-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | For i.MX6SX FEC controller, there have interrupt mask and event field extension. To support all SOCs FEC, we clear all interrupt events during MAVC initial process. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: fec: reset fep link status in suspend functionNimrod Andy2014-12-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On some i.MX6 serial boards, phy power and refrence clock are supplied or controlled by SOC. When do suspend/resume test, the power and clock are disabled, so phy device link down. For current driver, fep->link is still up status, which cause extra operation like below code. To avoid the dumy operation, we set fep->link to down when phy device is real down. ... if (fep->link) { napi_disable(&fep->napi); netif_tx_lock_bh(ndev); fec_stop(ndev); netif_tx_unlock_bh(ndev); napi_enable(&fep->napi); fep->link = phy_dev->link; status_change = 1; } ... Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: fec: avoid kernal crash by NULL pointer when no phy connectionNimrod Andy2014-12-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On i.MX6SX sabreauto board, when there have no phy daughter board connection, there have kernel crash by NULL pointer: fec 2188000.ethernet eth0: could not attach to PHY Unable to handle kernel NULL pointer dereference at virtual address 00000220 pgd = 80004000 [00000220] *pgd=00000000 Internal error: Oops: 5 [#1] PREEMPT SMP ARM Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.24-01042-g27eaeea-dirty #405 task: d8078000 ti: d8076000 task.ti: d8076000 PC is at mutex_lock+0x10/0x54 LR is at phy_start+0x14/0x68 pc : [<806ad4e4>] lr : [<803b0f90>] psr: 60000113 sp : d8077d80 ip : 00000000 fp : d83cc000 r10: 0000100c r9 : d83cc800 r8 : 00000000 r7 : d83bcd0c r6 : 00000200 r5 : 00000220 r4 : 00000220 r3 : 00000000 r2 : 00000000 r1 : d83bcd90 r0 : 00000220 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c5387d Table: 8000404a DAC: 00000015 Process swapper/0 (pid: 1, stack limit = 0xd8076240) Stack: (0xd8077d80 to 0xd8078000) 7d80: 00000000 803b0f90 00000001 00000000 d83bc800 803be034 00000007 805c3fb4 7da0: 00000003 80d4e0bc 805efcb8 fffffff1 fffffff0 00000000 00000000 d8077dfc 7dc0: 0000000d 80d6ce80 80d126b0 800499c8 d83bc800 d83bc800 806f0f40 d83bc82c 7de0: 00000000 00000000 80d6ce80 80d126b0 0000016b 80540250 d8076008 d83bc800 7e00: 0000016b d83bc800 00001003 00000001 00001002 805404d4 d83bc800 00000120 7e20: 00001002 00001002 00000000 805405d4 d83bc800 00000001 80d126c0 00001002 7e40: 80dbc5dc 80d02024 00000000 806ae360 00000002 d6128420 d6127198 12400000 7e60: 00000000 00000000 00000002 d61271e8 00000000 12400000 d801674c 800e49f0 7e80: d6127198 d6124e58 00000000 80238848 d61271c4 00000000 00000001 d8016700 7ea0: 80dd2e00 80d752c0 80d752c0 80cfdaec 0000010c 80239430 806c2e90 d800f080 7ec0: d800f380 804e46b4 ffffffbc 80d15cb0 00000007 80d752c0 80d752c0 80d01e94 7ee0: 0000010c d8076030 00000000 800088cc 80dbaba4 80bd411c d80a6f00 806b1e04 7f00: 00000000 00000000 00000000 80125b84 00000000 80d2c56c 60000113 00000001 7f20: ef7ff9df 806c80cc 0000010c 80043f5c 80c95eb8 00000007 ef7ffa1d 00000007 7f40: 80d2c55c 80d15cb0 00000007 80d752c0 80d752c0 80ccc50c 0000010c 80d0a114 7f60: 80d0a10c 80cccc04 00000007 00000007 80ccc50c 806ae410 00000000 8004cb84 7f80: 80d17bc0 00000000 806a4bd4 00000000 00000000 00000000 00000000 00000000 7fa0: 00000000 806a4bdc 00000000 8000e5f8 00000000 00000000 00000000 00000000 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 1e79a7bb e5337f77 [<806ad4e4>] (mutex_lock) from [<803b0f90>] (phy_start+0x14/0x68) [<803b0f90>] (phy_start) from [<803be034>] (fec_enet_open+0x448/0x5dc) [<803be034>] (fec_enet_open) from [<80540250>] (__dev_open+0xa8/0x110) [<80540250>] (__dev_open) from [<805404d4>] (__dev_change_flags+0x88/0x170) [<805404d4>] (__dev_change_flags) from [<805405d4>] (dev_change_flags+0x18/0x48) [<805405d4>] (dev_change_flags) from [<80d02024>] (ip_auto_config+0x190/0xf94) [<80d02024>] (ip_auto_config) from [<800088cc>] (do_one_initcall+0xe8/0x144) [<800088cc>] (do_one_initcall) from [<80cccc04>] (kernel_init_freeable+0x104/0x1c8) [<80cccc04>] (kernel_init_freeable) from [<806a4bdc>] (kernel_init+0x8/0xec) [<806a4bdc>] (kernel_init) from [<8000e5f8>] (ret_from_fork+0x14/0x3c) Code: e92d4010 e3a03000 e1a04000 ee073fba (e1903f9f) Add phydev check to fix the issue. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: fec: init maximum receive buffer size for ring1 and ring2Nimrod Andy2014-11-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | i.MX6SX fec support three rx ring1, the current driver lost to init ring1 and ring2 maximum receive buffer size, that cause receving frame date length error. The driver reports "rcv is not +last" error log in user case. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: fec: remove unused return value from swap_buffer()Lothar Waßmann2014-11-18
| | | | | | | | | | | | | | | | | | | | | | | | The return value of swap_buffer() is not used by any caller, thus remove it. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: fec: simplify loop counter handling in swap_buffer()Lothar Waßmann2014-11-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | Eliminate the DIV_ROUND_UP() and change the loop counter increment to 4 instead. This results in saving 6 instructions in the functions assembly code. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: fec: use swab32s() instead of cpu_to_be32()Lothar Waßmann2014-11-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | when swap_buffer() is being called, we know for sure, that we need to byte swap the data. Furthermore, this function is called for swapping data in both directions. Thus cpu_to_be32() is semantically not correct for all use cases. Use swab32s() to reflect this. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: fec: improve access to quirk flags by copying them into ↵Lothar Waßmann2014-11-18
| | | | | | | | | | | | | | | | | | | | | fec_enet_private struct Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: fec: change type of 'bufdesc_ex' to boolLothar Waßmann2014-11-18
| | | | | | | | | | | | | | | | | | | | | | | | fep->bufdesc_ex is treated as a boolean value, thus declare it as such. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: fec: fix regression on i.MX28 introduced by rx_copybreak supportLothar Waßmann2014-11-07
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 1b7bde6d659d ("net: fec: implement rx_copybreak to improve rx performance") introduced a regression for i.MX28. The swap_buffer() function doing the endian conversion of the received data on i.MX28 may access memory beyond the actual packet size in the DMA buffer. fec_enet_copybreak() does not copy those bytes, so that the last bytes of a packet may be filled with invalid data after swapping. This will likely lead to checksum errors on received packets. E.g. when trying to mount an NFS rootfs: UDP: bad checksum. From 192.168.1.225:111 to 192.168.100.73:44662 ulen 36 Do the byte swapping and copying to the new skb in one go if necessary. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: fec: fix suspend broken on multiple MACs silliconsNimrod Andy2014-11-03
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On i.MX6SX sdb platform, there has two same enet MACs, after system up, just eth0 is up, and then do suspend/resume test: [ 50.437967] PM: Syncing filesystems ... done. [ 50.476924] Freezing user space processes ... (elapsed 0.005 seconds) done. [ 50.490093] Freezing remaining freezable tasks ... (elapsed 0.004 seconds) done. [ 50.559771] ------------[ cut here ]------------ [ 50.564453] WARNING: CPU: 0 PID: 575 at drivers/clk/clk.c:851 __clk_disable+0x60/0x6c() [ 50.572475] Modules linked in: [ 50.575578] CPU: 0 PID: 575 Comm: sh Not tainted 3.18.0-rc2-next-20141031-00007-gf61135b #21 [ 50.584031] Backtrace: [ 50.586550] [<80011ecc>] (dump_backtrace) from [<8001206c>] (show_stack+0x18/0x1c) [ 50.594136] r6:808a7a54 r5:00000000 r4:00000000 r3:00000000 [ 50.599920] [<80012054>] (show_stack) from [<806ab3c0>] (dump_stack+0x80/0x9c) [ 50.607187] [<806ab340>] (dump_stack) from [<8002a3e8>] (warn_slowpath_common+0x6c/0x8c) [ 50.615294] r5:00000353 r4:00000000 [ 50.618940] [<8002a37c>] (warn_slowpath_common) from [<8002a42c>] (warn_slowpath_null+0x24/0x2c) [ 50.627738] r8:00000000 r7:be144c44 r6:be015600 r5:80070013 r4:be015600 [ 50.634573] [<8002a408>] (warn_slowpath_null) from [<804f8d4c>] (__clk_disable+0x60/0x6c) [ 50.642777] [<804f8cec>] (__clk_disable) from [<804f8e5c>] (clk_disable+0x2c/0x38) [ 50.650359] r4:be015600 r3:00000000 [ 50.654006] [<804f8e30>] (clk_disable) from [<80420ab4>] (fec_enet_clk_enable+0xc4/0x258) [ 50.662196] r5:be3cb620 r4:be3cb000 [ 50.665838] [<804209f0>] (fec_enet_clk_enable) from [<80421178>] (fec_suspend+0x30/0x180) [ 50.674026] r7:be144c44 r6:be144c10 r5:8037f5a4 r4:be3cb000 [ 50.679802] [<80421148>] (fec_suspend) from [<8037f5d8>] (platform_pm_suspend+0x34/0x64) [ 50.687906] r10:00000000 r9:00000000 r8:00000000 r7:be144c44 r6:be144c10 r5:8037f5a4 [ 50.695852] r4:be144c10 r3:80421148 [ 50.699511] [<8037f5a4>] (platform_pm_suspend) from [<8038784c>] (dpm_run_callback.isra.14+0x34/0x6c) [ 50.708764] [<80387818>] (dpm_run_callback.isra.14) from [<80387f00>] (__device_suspend+0x12c/0x2a4) [ 50.717909] r9:8098ec8c r8:80973bec r6:00000002 r5:811c7038 r4:be144c10 [ 50.724746] [<80387dd4>] (__device_suspend) from [<803894fc>] (dpm_suspend+0x64/0x224) [ 50.732675] r8:80973bec r7:be144c10 r6:8098ec24 r5:811c7038 r4:be144cc4 [ 50.739509] [<80389498>] (dpm_suspend) from [<8038999c>] (dpm_suspend_start+0x60/0x68) [ 50.747438] r10:8082fa24 r9:00000000 r8:00000004 r7:00000003 r6:00000000 r5:8116ec80 [ 50.755386] r4:00000002 [ 50.757969] [<8038993c>] (dpm_suspend_start) from [<800679d8>] (suspend_devices_and_enter+0x90/0x3ec) [ 50.767202] r4:00000003 r3:8116eca0 [ 50.770843] [<80067948>] (suspend_devices_and_enter) from [<80067f40>] (pm_suspend+0x20c/0x2a4) [ 50.779553] r8:00000004 r7:00000003 r6:00000000 r5:8116ec8c r4:00000003 [ 50.786394] [<80067d34>] (pm_suspend) from [<80066858>] (state_store+0x70/0xc0) [ 50.793718] r6:8116ec90 r5:00000003 r4:bd88a800 r3:0000006d [ 50.799496] [<800667e8>] (state_store) from [<802b0384>] (kobj_attr_store+0x1c/0x28) [ 50.807251] r10:bd399f78 r8:00000000 r7:bd88a800 r6:bd88a800 r5:00000004 r4:bd085680 [ 50.815219] [<802b0368>] (kobj_attr_store) from [<80153090>] (sysfs_kf_write+0x54/0x58) [ 50.823252] [<8015303c>] (sysfs_kf_write) from [<80151fd8>] (kernfs_fop_write+0xd0/0x194) [ 50.831441] r6:00000004 r5:bd08568c r4:bd085680 r3:8015303c [ 50.837220] [<80151f08>] (kernfs_fop_write) from [<800eddb4>] (vfs_write+0xb8/0x1a8) [ 50.844975] r10:00000000 r9:00000000 r8:00000000 r7:bd399f78 r6:01336408 r5:00000004 [ 50.852924] r4:bc584dc0 [ 50.855505] [<800edcfc>] (vfs_write) from [<800ee0b8>] (SyS_write+0x48/0x88) [ 50.862567] r10:00000000 r8:00000000 r7:01336408 r6:00000004 r5:bc584dc0 r4:bc584dc0 [ 50.870537] [<800ee070>] (SyS_write) from [<8000eb00>] (ret_fast_syscall+0x0/0x48) [ 50.878120] r9:bd398000 r8:8000ecc4 r7:00000004 r6:76f42b48 r5:01336408 r4:00000004 [ 50.885983] ---[ end trace 7545115d752a316a ]--- [ 50.890765] ------------[ cut here ]------------ The root cause is that eth1 is not opened and clock is not enabled, and .suspend() still call .fec_enet_clk_enable() to disable clock. To avoid the broken, let it check network device up status by calling .netif_running() before disable/enable clocks. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* / net: fec: ptp: fix NULL pointer dereference if ptp_clock is not setPhilipp Zabel2014-10-22
|/ | | | | | | | | | | | | | Since commit 278d24047891 (net: fec: ptp: Enable PPS output based on ptp clock) fec_enet_interrupt calls fec_ptp_check_pps_event unconditionally, which calls into ptp_clock_event. If fep->ptp_clock is NULL, ptp_clock_event tries to dereference the NULL pointer. Since on i.MX53 fep->bufdesc_ex is not set, fec_ptp_init is never called, and fep->ptp_clock is NULL, which reliably causes a kernel panic. This patch adds a check for fep->ptp_clock == NULL in fec_enet_interrupt. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: ptp: fix convergence issue to support LinuxPTP stackNimrod Andy2014-10-15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | iMX6SX IEEE 1588 module has one hw issue in capturing the ATVR register. The current SW flow is: ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK; ts_counter_ns = ENET0->ATVR; The ATVR value is not expected value that cause LinuxPTP stack cannot be convergent. ENET Block Guide/ Chapter for the iMX6SX (PELE) address the issue: After set ENET_ATCR[Capture], there need some time cycles before the counter value is capture in the register clock domain. The wait-time-cycles is at least 6 clock cycles of the slower clock between the register clock and the 1588 clock. So need something like: ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK; wait(); ts_counter_ns = ENET0->ATVR; For iMX6SX, the 1588 ts_clk is fixed to 25Mhz, register clock is 66Mhz, so the wait-time-cycles must be greater than 240ns (40ns * 6). The patch add 1us delay before cpu read ATVR register. Changes V2: Modify the commit/comments log to describe the issue clearly. Signed-off-by: Fugang Duan <B38611@freescale.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: ptp: Enable PPS output based on ptp clockLuwei Zhou2014-10-14
| | | | | | | | | | | | | FEC ptp timer has 4 channel compare/trigger function. It can be used to enable pps output. The pulse would be ouput high exactly on N second. The pulse ouput high on compare event mode is used to produce pulse per second. The pulse width would be one cycle based on ptp timer clock source.Since 31-bit ptp hardware timer is used, the timer will wrap more than 2 seconds. We need to reload the compare compare event about every 1 second. Signed-off-by: Luwei Zhou <b45643@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: Fix sparse warnings with different lock contexts for basic blockNimrod Andy2014-10-14
| | | | | | | | | | | | | | | | | | | | | | | | reproduce: make ARCH=arm C=1 2>fec.txt drivers/net/ethernet/freescale/fec_main.o cat fec.txt sparse warnings: drivers/net/ethernet/freescale/fec_main.c:2916:12: warning: context imbalance in 'fec_set_features' - different lock contexts for basic block Christopher Li suggest to change as below: if (need_lock) { lock(); do_something_real(); unlock(); } else { do_something_real(); } Reported-by: Fabio Estevam <festevam@gmail.com> Suggested-by: Christopher Li <sparse@chrisli.org> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* fec: Fix fec_enet_alloc_buffers() error pathFabio Estevam2014-10-06
| | | | | | | | | | | When fec_enet_alloc_buffers() fails we should better undo the previous actions, which consists of: disabling the FEC clocks and putting the FEC pins into inactive state. The error path for fec_enet_mii_probe() is kept unchanged. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: fix build error at m68k platformFrank Li2014-10-06
| | | | | | | | | | | | | | | | | | | | | | | | reproduce: wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross git checkout 1b7bde6d659d30f171259cc2dfba8e5dab34e735 make.cross ARCH=m68k m5275evb_defconfig make.cross ARCH=m68k All error/warnings: drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_rx_queue': >> drivers/net/ethernet/freescale/fec_main.c:1470:3: error: implicit declaration of function 'prefetch' [-Werror=implicit-function-declaration] prefetch(skb->data - NET_IP_ALIGN); ^ cc1: some warnings being treated as errors missed included prefetch.h Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: implement rx_copybreak to improve rx performanceNimrod Andy2014-10-01
| | | | | | | | | | | | | | | | | | | - Copy short frames and keep the buffers mapped, re-allocate skb instead of memory copy for long frames. - Add support for setting/getting rx_copybreak using generic ethtool tunable Changes V3: * As Eric Dumazet's suggestion that removing the copybreak module parameter and only keep the ethtool API support for rx_copybreak. Changes V2: * Implements rx_copybreak * Rx_copybreak provides module parameter to change this value * Add tunable_ops support for rx_copybreak Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: free resource after phy probe failedNimrod Andy2014-09-26
| | | | | | | | Free memory and disable all related clocks when there has no phy connection or phy probe failed. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: align rx data buffer size for dma map/unmapNimrod Andy2014-09-26
| | | | | | | | Align allocated rx data buffer size for dma map/unmap, otherwise kernel print warning when enable DMA_API_DEBUG. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: remove the ERR006358 workaround for imx6sx enetNimrod Andy2014-09-26
| | | | | | | | Remove the ERR006358 workaround for imx6sx enet since the hw issue was fixed on the SOC. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: Add Ftype to BD to distiguish three tx queues for AVBNimrod Andy2014-09-26
| | | | | | | | | | | | | The current driver loss Ftype field init for BD, which cause tx queue #1 and #2 cannot work well. Add Ftype field to BD to distiguish three queues for AVB: 0 -> Best Effort 1 -> ClassA 2 -> ClassB Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* fec: Remove fec_enet_select_queue()Fabio Estevam2014-09-26
| | | | | | | | | | | | | | | | | | | | | | | | Sparse complains about fec_enet_select_queue() not being static. Feedback from David Miller [1] was to remove this function instead of making it static: "Please just delete this function. It's overriding code which does exactly the same thing. Actually, more precisely, this code is duplicating code in a way that bypasses many core facilitites of the networking. For example, this override means that socket based flow steering, XPS, etc. are all not happening on these devices. Without ->ndo_select_queue(), the flow dissector does __netdev_pick_tx which is exactly what you want to happen." [1] http://www.spinics.net/lists/netdev/msg297653.html Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: fix code identationNimrod Andy2014-09-22
| | | | | | | | | There have extra identation before .skb_copy_to_linear_data_offset(), this patch just remove the identation. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: Workaround for imx6sx enet tx hang when enable three queuesFugang Duan2014-09-19
| | | | | | | | | | | | | | | | | | | | | | | When enable three queues on imx6sx enet, and then do tx performance test with iperf tool, after some time running, tx hang. Found that: If uDMA is running, software set TDAR may cause tx hang. If uDMA is in idle, software set TDAR don't cause tx hang. There is a TDAR race condition for mutliQ when the software sets TDAR and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles). This will cause the udma_tx and udma_tx_arbiter state machines to hang. The issue exist at i.MX6SX enet IP. So, the Workaround is checking TDAR status four time, if TDAR cleared by hardware and then write TDAR, otherwise don't set TDAR. The patch is only one Workaround for the issue ERR007885. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: add interrupt coalescence feature supportFugang Duan2014-09-19
| | | | | | | | | | | | | | | | | i.MX6 SX support interrupt coalescence feature By default, init the interrupt coalescing frame count threshold and timer threshold. Supply the ethtool interfaces as below for user tuning to improve enet performance: rx_max_coalesced_frames rx_coalesce_usecs tx_max_coalesced_frames tx_coalesce_usecs Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: refine error handle of parser queue number from DTFrank Li2014-09-19
| | | | | | | | | check tx and rx queue seperately. fix typo, "Invalidate" and "fail". change pr_err to pr_warn. Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethernet: freescale: fec_main.c: Cleaning up missing null-terminate in ↵Rickard Strandqvist2014-09-15
| | | | | | | | | conjunction with strncpy Replacing strncpy with strlcpy to avoid strings that lacks null terminate. Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: use container_of to resolve bufdesc_ex from bufdescFabian Frederick2014-09-15
| | | | | | | | | Use container_of instead of casting first structure member. ARM cross-compiled but untested. Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: init complete variable in early to avoid kernel dumpFugang Duan2014-09-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Software clear the MDIO interrupt before MDIO bus access, but MAC still generate MDIO interrupt. The issue only happen on imx6slx chip. CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.0-rc1-00399-g0bcad17 #315 Backtrace: [<800121fc>] (dump_backtrace) from [<800124e0>] (show_stack+0x18/0x1c) r6:8096e534 r5:8096e534 r4:00000000 r3:00000000 [<800124c8>] (show_stack) from [<806a4c60>] (dump_stack+0x8c/0xa4) [<806a4bd4>] (dump_stack) from [<80060ab8>] (__lock_acquire+0x1814/0x1c40) r6:be078000 r5:be074000 r4:be03f6e4 r3:be078000 [<8005f2a4>] (__lock_acquire) from [<800616e0>] (lock_acquire+0x70/0x84) r10:809ada33 r9:be010600 r8:00000096 r7:00000001 r6:be074000 r5:00000000 r4:60000193 [<80061670>] (lock_acquire) from [<806abb20>] (_raw_spin_lock_irqsave+0x40/0x54) r7:00000000 r6:8005a3f8 r5:00000193 r4:be03f6d4 [<806abae0>] (_raw_spin_lock_irqsave) from [<8005a3f8>] (complete+0x1c/0x4c) r6:80950904 r5:be03f6d0 r4:be03f6d4 [<8005a3dc>] (complete) from [<8041b4c0>] (fec_enet_interrupt+0x128/0x164) r6:80950904 r5:00800000 r4:be03f000 r3:00000000 [<8041b398>] (fec_enet_interrupt) from [<8006aeac>] (handle_irq_event_percpu+0x38/0x13c) r6:00000000 r5:be01065c r4:be399e00 r3:8041b398 [<8006ae74>] (handle_irq_event_percpu) from [<8006aff4>] (handle_irq_event+0x44/0x64) r10:be03f000 r9:80989fe0 r8:00000000 r7:00000096 r6:be399e00 r5:be01065c r4:be010600 [<8006afb0>] (handle_irq_event) from [<8006e3e8>] (handle_fasteoi_irq+0xc8/0x1bc) r6:8096e764 r5:be01065c r4:be010600 r3:00000000 [<8006e320>] (handle_fasteoi_irq) from [<8006a63c>] (generic_handle_irq+0x30/0x44) r6:be074010 r5:80945e4c r4:00000096 r3:8006e320 [<8006a60c>] (generic_handle_irq) from [<8000f218>] (handle_IRQ+0x54/0xbc) r4:80950d74 r3:00000180 [<8000f1c4>] (handle_IRQ) from [<800086cc>] (gic_handle_irq+0x30/0x68) r8:be3ab478 r7:c080e100 r6:be075bd8 r5:80950eec r4:c080e10c r3:000000a0 [<8000869c>] (gic_handle_irq) from [<80013064>] (__irq_svc+0x44/0x5c) Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: change FEC alignment according to i.mx6 sx requirementFugang Duan2014-09-13
| | | | | | | | | | | i.MX6 SX change FEC alignment requirement. i.MX6 SX change internal bus from AHB to AXI. It require RX buffer must be 64 bytes alignment. And remove TX buffer alignment requirement. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net:fec: Add fsl,imx6sx-fec compatible stringsFugang Duan2014-09-13
| | | | | | | | Add compatible string "fsl,imx6sx-fec" for i.MX6SX. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: add enet-avb IP supportFrank Li2014-09-13
| | | | | | | | | | | | | | | | | i.MX6SX Enet-AVB support 3 tx queues, 3 rx queues. For tx queues: ring 0 -> best effort ring 1 -> Class A ring 2 -> Class B For rx queues: ring 0 -> best effort ring 1 -> receive VLAN packet with classification match ring 2 -> receive VLAN packet with classification match Add enet-avb IP multiqueue support for the driver. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.2 (git 2.25.0) at 2024-09-21 03:36:55 -0400