| Commit message (Collapse) | Author | Age |
|---|
| ... | |
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
These interfaces:
pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)
took a pci_dev, but they really depend only on the pci_bus. And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:
pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)
In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | | |/ / /
| |/| | |
| | | | |
| | | | |
| | | | |
| | | | | |
Struct pci_bus_region contains bus addresses, which are type dma_addr_t,
not resource_size_t.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |\ \ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
* pci/msi:
PCI/MSI: Add pci_enable_msi_range() and pci_enable_msix_range()
PCI/MSI: Add pci_msix_vec_count()
PCI/MSI: Remove pci_enable_msi_block_auto()
PCI/MSI: Add pci_msi_vec_count()
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This adds pci_enable_msi_range(), which supersedes the pci_enable_msi()
and pci_enable_msi_block() MSI interfaces.
It also adds pci_enable_msix_range(), which supersedes the
pci_enable_msix() MSI-X interface.
The old interfaces have three categories of return values:
negative: failure; caller should not retry
positive: failure; value indicates number of interrupts that *could*
have been allocated, and caller may retry with a smaller request
zero: success; at least as many interrupts allocated as requested
It is error-prone to handle these three cases correctly in drivers.
The new functions return either a negative error code or a number of
successfully allocated MSI/MSI-X interrupts, which is expected to lead to
clearer device driver code.
pci_enable_msi(), pci_enable_msi_block() and pci_enable_msix() still exist
unchanged, but are deprecated and may be removed after callers are updated.
[bhelgaas: tweak changelog]
Suggested-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This creates an MSI-X counterpart for pci_msi_vec_count(). Device drivers
can use this function to obtain maximum number of MSI-X interrupts the
device supports and use that number in a subsequent call to
pci_enable_msix().
pci_msix_vec_count() supersedes pci_msix_table_size() and returns a
negative errno if device does not support MSI-X interrupts. After this
update, callers must always check the returned value.
The only user of pci_msix_table_size() was the PCI-Express port driver,
which is also updated by this change.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The new pci_msi_vec_count() interface makes pci_enable_msi_block_auto()
superfluous.
Drivers can use pci_msi_vec_count() to learn the maximum number of MSIs
supported by the device, and then call pci_enable_msi_block().
pci_enable_msi_block_auto() was introduced recently, and its only user is
the AHCI driver, which is also updated by this change.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Device drivers can use this interface to obtain the maximum number of MSI
interrupts the device supports and use that number, e.g., in a subsequent
call to pci_enable_msi_block().
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
|
| |\ \ \ \ \ \
| | |_|_|/ /
| |/| | | |
| | | | | |
| | | | | |
| | | | | | |
* pci/misc:
PCI: Update documentation 00-INDEX file
PCI: Convert ioapic to be builtin only, not modular
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The PCI-DMA-mapping.txt moved to general docs and became DMA-API-HOWTO.txt
in 5e07c2c7301b ("Documentation: rename PCI/PCI-DMA-mapping.txt to
DMA-API-HOWTO.txt"). Add new file about PCI Express I/O Virtualization.
Signed-off-by: Erik Ekman <erik@kryo.se>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Convert pci/ioapic.c to be builtin only, with no module option, so we can
support IO-APIC hotplug. Also make it depend on X86_IO_APIC.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |\ \ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
* pci/host-mvebu:
PCI: mvebu: Use max_t() instead of max(resource_size_t,)
PCI: mvebu: Call pci_ioremap_io() at startup instead of dynamically
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Use max_t() instead of max(resource_size_t,) in order to fix
the following checkpatch warning.
WARNING: max() should probably be max_t(resource_size_t, SZ_64K, size)
WARNING: max() should probably be max_t(resource_size_t, SZ_1M, size)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The mvebu PCI host controller driver uses an emulated PCI-to-PCI bridge to
leverage the core PCI kernel enumeration logic to dynamically create and
remove the MBus windows needed to access the memory and I/O regions of each
PCI interface.
In the context of this PCI-to-PCI bridge emulation, the driver emulates
all reads and writes to the PCI bridge registers. Upon a write to the
registers configuring the I/O base and limit, the driver was creating the
MBus window and calling pci_ioremap_io() to setup the mapping.
However, it turns out that accesses to these registers are made in an IRQ
disabled context, while pci_ioremap_io() is a potentially sleeping
function. Not only this is wrong, but it is causing fairly loud warnings
at boot time when the appropriate kernel hacking options are enabled.
This patch solves this by moving the pci_ioremap_io() call to the startup
of the driver. At this point, we don't know how many PCI interfaces will
be enabled, so we are simply remapping the entire PCI I/O space to virtual
addresses. This is reasonable since this I/O space is limited to 1 MB in
size, and also because the MBus windows continue to be created in a dynamic
fashion only when devices need them.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |\ \ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
* pci/host-designware:
PCI: designware: Fix indent code style
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Fix indent code style and replace 'MSI interrupt controller' of comment
with 'MSI controller' to fix the following checkpatch issues:
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
WARNING: line over 80 characters
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |\ \ \ \ \ \ \ \
| | |_|/ / / / /
| |/| | | | | |
| | | | | | | |
| | | | | | | | |
* pci/misc:
PCI/checkpatch: Deprecate DEFINE_PCI_DEVICE_TABLE
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Prefer use of the direct definition of struct pci_device_id instead of
indirection via macro DEFINE_PCI_DEVICE_TABLE.
Update the PCI documentation to deprecate DEFINE_PCI_DEVICE_TABLE. Update
checkpatch adding --fix option.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
|
| |\ \ \ \ \ \ \ \
| | |_|_|/ / / /
| |/| | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
* pci/msi:
PCI/MSI: Make pci_enable_msi/msix() 'nvec' argument type as int
PCI/MSI: Return -ENOSYS for unimplemented interfaces, not -1
PCI/MSI: Return msix_capability_init() failure if populate_msi_sysfs() fails
s390/PCI: Remove superfluous check of MSI type
s390/PCI: Fix single MSI only check
PCI/MSI: Export MSI mode using attributes, not kobjects
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Make pci_enable_msi_block(), pci_enable_msi_block_auto() and
pci_enable_msix() consistent with regard to the type of 'nvec' argument.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Suggested-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
If populate_msi_sysfs() function failed msix_capability_init() must return
the error code, but it returns the success instead. This update fixes the
described misbehaviour.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
arch_setup_msi_irqs() hook can only be called from the generic MSI code
which ensures correct MSI type parameter.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Multiple MSIs have never been supported on s390 architecture, but the
platform code fails to report single MSI only.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
| | | |_|_|/ / /
| |/| | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The PCI MSI sysfs code is a mess with kobjects for things that don't really
need to be kobjects. This patch creates attributes dynamically for the MSI
interrupts instead of using kobjects.
Note, this removes a directory from sysfs. Old MSI kobjects:
pci_device
└── msi_irqs
  └── 40
  └── mode
New MSI attributes:
pci_device
└── msi_irqs
  └── 40
As there was only one file "mode" with the kobject model, the interrupt
number is now a file that returns the "mode" of the interrupt (msi vs.
msix).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
|
| |\ \ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
* pci/deletion:
PCI/portdrv: Remove extra get_device()/put_device() for pcie_device
PCI/portdrv: Add put_device() after device_register() failure
PCI/portdrv: Cleanup error paths
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Previously pcie_device_init() called get_device() if device_register() for
the new pcie_device succeeded, and remove_iter() called put_device() when
removing before unregistering the device.
But device_register() already increments the reference count in
device_add(), so we don't need to do it again here.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
This is required so that we give up the last reference to the device.
Removed the kfree() as put_device will result in release_pcie_device()
being called and hence the container of the device will be kfree'd.
[bhelgaas: fix conflict after my previous cleanup]
Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Make the straightline path the normal no-error path. Check for errors and
return them directly, instead of checking for success and putting the
normal path in an "if" body.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |\ \ \ \ \ \ \ \
| | |_|_|/ / / /
| |/| | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
* pci/host-designware:
PCI: designware: Fix I/O transfers by using CPU (not realio) address
PCI: designware: Add dw_pcie prefix before cfg_read/write
PCI: designware: Fix missing MSI IRQs
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
pp->io_base, which is the input of the outbound IO address translation
unit, should be the CPU address. It was incorrectly programmed to the
realio address.
We should pass global_io_offset rather than sys->io_offset to
pci_ioremap_io(), so we map the new window into the first available spot in
the Linux view of the I/O space.
We must also pass CPU address instead of realio address to pci_ioremap_io().
This patch fixes above issue. It has been tested with Lecroy PTC in AIC
mode and Pericom PI7C9X2G303EL PCIe switch, which does not work otherwise.
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marek Vasut <marex@denx.de
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Zhu <Hong-Xing.Zhu@freescale.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
The cfg_read/write functions are DesignWare-specific. Add dw_pcie prefix
to avoid collision in global name space.
Tested-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
The interrupts were cleared after the IRQ handler was called. This means
that new interrupts that occur after the handler handled the previous IRQ
but before the interrupt is cleared will be missed.
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Matthias Mann <m.mann@arkona-technologies.de>
Signed-off-by: Harro Haan <hrhaan@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Richard Zhu <hong-xing.zhu@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Juergen Beisert <jbe@pengutronix.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Sean Cross <xobs@kosagi.com>
|
| |\ \ \ \ \ \ \ \
| | |_|_|_|/ / /
| |/| | | | | |
| | | | | | | |
| | | | | | | | |
* pci/host-mvebu:
PCI: mvebu: Remove redundant of_match_ptr
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
mvebu_pcie_of_match_table is always compiled in. Hence of_match_ptr is not
required.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
| |\ \ \ \ \ \ \ \
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
* pci/host-imx6:
PCI: imx6: Fix bugs in PCIe startup code
PCI: imx6: Start link in Gen1 before negotiating for Gen2 mode
PCI: imx6: Factor out link up wait loop
PCI: imx6: Factor out PHY reset
PCI: imx6: Report "link up" only after link training completes
PCI: imx6: Make reset-gpio optional
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
LTSSM shouldn't be set once in assert_core_reset(). Move peripheral reset
just before LTSSM start.
Signed-off-by: Richard Zhu <r65037@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
This patch first forces the link into Gen1 mode before starting up the link
and, only after the link is up, start negotiating possible Gen2 mode
operation. This is because without such sequence, some PCIe switches are
not detected at all.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
Split the function that waits for the PCIe link to come up from the rest if
the host init function. We will find this change useful in the subsequent
patch, since this will be called twice then.
No functional change.
[bhelgaas: remove useless "return;"]
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
Split the PCIe PHY reset from the link up function to make the code a
little more structured.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
While waiting for the PHY to report the PCIe link is up, we might hit a
situation where the link training is still in progress, while the PHY
already reports the link is up. Add additional check for this condition.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
Some boards do not have a PCIe reset GPIO. To avoid probe failure on these
boards, make the reset GPIO optional as well.
[bhelgaas: whitespace fixes]
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
|
| |\ \ \ \ \ \ \ \ \
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | | |
* pci/vc:
PCI: Rename PCI_VC_PORT_REG1/2 to PCI_VC_PORT_CAP1/2
PCI: Add Virtual Channel to save/restore support
PCI: Add support for save/restore of extended capabilities
PCI: Add pci_wait_for_pending() (refactor pci_wait_for_pending_transaction())
|
| | | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | | |
These are set of two capability registers, it's pretty much given that
they're registers, so reflect their purpose in the name.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | | |
While we don't really have any infrastructure for making use of VC
support, the system BIOS can configure the topology to non-default
VC values prior to boot. This may be due to silicon bugs, desire to
reserve traffic classes, or perhaps just BIOS bugs. When we reset
devices, the VC configuration may return to default values, which can
be incompatible with devices upstream. For instance, Nvidia GRID
cards provide a PCIe switch and some number of GPUs, all supporting
VC. The power-on default for VC is to support TC0-7 across VC0,
however some platforms will only enable TC0/VC0 mapping across the
topology. When we do a secondary bus reset on the downstream switch
port, the GPU is reset to a TC0-7/VC0 mapping while the opposite end
of the link only enables TC0/VC0. If the GPU attempts to use TC1-7,
it fails.
This patch attempts to provide complete support for VC save/restore,
even beyond the minimally required use case above. This includes
save/restore and reload of the arbitration table, save/restore and
reload of the port arbitration tables, and re-enabling of the
channels for VC, VC9, and MFVC capabilities.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | | |
Current save/restore is specific to standard capabilities.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | | |_|_|_|/ / / /
| |/| | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
We currently have two instance of this loop which waits for a pending bit
to clear in a status dword. Generalize the function for future users.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |\ \ \ \ \ \ \ \ \
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | | |
* pci/pciehp:
PCI: pciehp: Move Attention & Power Indicator support tests to accessors
PCI: pciehp: Use symbolic constants for Slot Control fields
PCI: pciehp: Use symbolic constants, not hard-coded bitmask
PCI: pciehp: Simplify "Power Fault Detected" checking/clearing
PCI: pciehp: Announce slot capabilities (slot #, button, LEDs, etc)
PCI: pciehp: Make various functions void since they can't fail
PCI: pciehp: Remove error checks when accessing PCIe Capability
PCI: pciehp: Drop pciehp_readw()/pciehp_writew() wrappers
|
| | | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | | |
Previously, the caller checked ATTN_LED() or PWR_LED() to see whether the
slot has indicators before setting the indicator state. That clutters the
caller unnecessarily, so this moves the test inside the callees. The test
may not even be necessary; per spec it should be harmless to try to turn on
a non-existent LED. But checking first does avoid unnecessary hotplug
commands.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | | |
Add symbolic constants for the PCIe Slot Control indicator and power
control fields defined by spec and use them instead of open-coded hex
constants.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | | |
Use the PCI_EXP_SLTSTA definitions, not 0x1f, when clearing Slot Status
bits.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
