USB: Merge 2.6.37-rc5 into usb-next

This is to resolve the conflict in the file,
drivers/usb/gadget/composite.c that was due to a revert in Linus's tree
needed for the 2.6.37 release.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1 files changed, 3 insertions, 95 deletions

diff --git a/arch/arm/mach-at91/board-pcontrol-g20.c b/arch/arm/mach-at91/board-pcontrol-g20.c
index bba5a560e02b..feb65787c30b 100644
--- a/arch/arm/mach-at91/board-pcontrol-g20.c
+++ b/arch/arm/mach-at91/board-pcontrol-g20.c
@@ -31,6 +31,7 @@
 
 #include <mach/board.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/stamp9g20.h>
 
 #include "sam9_smc.h"
 #include "generic.h"
@@ -38,11 +39,7 @@
 
 static void __init pcontrol_g20_map_io(void)
 {
-        /* Initialize processor: 18.432 MHz crystal */
-        at91sam9260_initialize(18432000);
-
-        /* DGBU on ttyS0. (Rx, Tx) only TTL -> JTAG connector X7 17,19 ) */
-        at91_register_uart(0, 0, 0);
+        stamp9g20_map_io();
 
         /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback  A2 */
         at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
@@ -54,9 +51,6 @@ static void __init pcontrol_g20_map_io(void)
 
         /* USART2 on ttyS3. (Rx, Tx)  9bit-Bus  Multidrop-mode  X4 */
         at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
-
-        /* set serial console to ttyS0 (ie, DBGU) */
-        at91_set_serial_console(0);
 }
 
 
@@ -66,38 +60,6 @@ static void __init init_irq(void)
 }
 
 
-/*
- * NAND flash 512MiB 1,8V 8-bit, sector size 128 KiB
- */
-static struct atmel_nand_data __initdata nand_data = {
-        .ale            = 21,
-        .cle            = 22,
-        .rdy_pin        = AT91_PIN_PC13,
-        .enable_pin     = AT91_PIN_PC14,
-};
-
-/*
- * Bus timings; unit = 7.57ns
- */
-static struct sam9_smc_config __initdata nand_smc_config = {
-        .ncs_read_setup         = 0,
-        .nrd_setup              = 2,
-        .ncs_write_setup        = 0,
-        .nwe_setup              = 2,
-
-        .ncs_read_pulse         = 4,
-        .nrd_pulse              = 4,
-        .ncs_write_pulse        = 4,
-        .nwe_pulse              = 4,
-
-        .read_cycle             = 7,
-        .write_cycle            = 7,
-
-        .mode                   = AT91_SMC_READMODE | AT91_SMC_WRITEMODE
-                        | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
-        .tdf_cycles             = 3,
-};
-
 static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {
         .ncs_read_setup         = 16,
         .nrd_setup              = 18,
@@ -138,14 +100,6 @@ static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {
         .tdf_cycles             = 1,
 } };
 
-static void __init add_device_nand(void)
-{
-        /* configure chip-select 3 (NAND) */
-        sam9_smc_configure(3, &nand_smc_config);
-        at91_add_device_nand(&nand_data);
-}
-
-
 static void __init add_device_pcontrol(void)
 {
         /* configure chip-select 4 (IO compatible to 8051  X4 ) */
@@ -156,23 +110,6 @@ static void __init add_device_pcontrol(void)
 
 
 /*
- * MCI (SD/MMC)
- * det_pin, wp_pin and vcc_pin are not connected
- */
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
-static struct mci_platform_data __initdata mmc_data = {
-        .slot[0] = {
-                .bus_width      = 4,
-        },
-};
-#else
-static struct at91_mmc_data __initdata mmc_data = {
-        .wire4          = 1,
-};
-#endif
-
-
-/*
  * USB Host port
  */
 static struct at91_usbh_data __initdata usbh_data = {
@@ -265,42 +202,13 @@ static struct spi_board_info pcontrol_g20_spi_devices[] = {
 };
 
 
-/*
- * Dallas 1-Wire  DS2431
- */
-static struct w1_gpio_platform_data w1_gpio_pdata = {
-        .pin            = AT91_PIN_PA29,
-        .is_open_drain  = 1,
-};
-
-static struct platform_device w1_device = {
-        .name                   = "w1-gpio",
-        .id                     = -1,
-        .dev.platform_data      = &w1_gpio_pdata,
-};
-
-static void add_wire1(void)
-{
-        at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
-        at91_set_multi_drive(w1_gpio_pdata.pin, 1);
-        platform_device_register(&w1_device);
-}
-
-
 static void __init pcontrol_g20_board_init(void)
 {
-        at91_add_device_serial();
-        add_device_nand();
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
-        at91_add_device_mci(0, &mmc_data);
-#else
-        at91_add_device_mmc(0, &mmc_data);
-#endif
+        stamp9g20_board_init();
         at91_add_device_usbh(&usbh_data);
         at91_add_device_eth(&macb_data);
         at91_add_device_i2c(pcontrol_g20_i2c_devices,
                 ARRAY_SIZE(pcontrol_g20_i2c_devices));
-        add_wire1();
         add_device_pcontrol();
         at91_add_device_spi(pcontrol_g20_spi_devices,
                 ARRAY_SIZE(pcontrol_g20_spi_devices));