From c20b4dd31820a551d0fb60bf27b99345905c2eb6 Mon Sep 17 00:00:00 2001 From: Christian Glindkamp Date: Thu, 9 Dec 2010 11:15:59 +0100 Subject: at91: Refactor Stamp9G20 and PControl G20 board file As PControl G20 is a carrier board for the Stamp9G20 SoM, some code can be shared. Therefore board-stamp9g20.c is refactored to allow reusing the SoM initialization and board-pcontrol-g20.c is modified to use it. Signed-off-by: Christian Glindkamp Signed-off-by: Nicolas Ferre --- arch/arm/mach-at91/board-pcontrol-g20.c | 98 +-------------------------------- 1 file changed, 3 insertions(+), 95 deletions(-) (limited to 'arch/arm/mach-at91/board-pcontrol-g20.c') diff --git a/arch/arm/mach-at91/board-pcontrol-g20.c b/arch/arm/mach-at91/board-pcontrol-g20.c index bba5a560e02b..feb65787c30b 100644 --- a/arch/arm/mach-at91/board-pcontrol-g20.c +++ b/arch/arm/mach-at91/board-pcontrol-g20.c @@ -31,6 +31,7 @@ #include #include +#include #include "sam9_smc.h" #include "generic.h" @@ -38,11 +39,7 @@ static void __init pcontrol_g20_map_io(void) { - /* Initialize processor: 18.432 MHz crystal */ - at91sam9260_initialize(18432000); - - /* DGBU on ttyS0. (Rx, Tx) only TTL -> JTAG connector X7 17,19 ) */ - at91_register_uart(0, 0, 0); + stamp9g20_map_io(); /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback A2 */ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS @@ -54,9 +51,6 @@ static void __init pcontrol_g20_map_io(void) /* USART2 on ttyS3. (Rx, Tx) 9bit-Bus Multidrop-mode X4 */ at91_register_uart(AT91SAM9260_ID_US4, 3, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } @@ -66,38 +60,6 @@ static void __init init_irq(void) } -/* - * NAND flash 512MiB 1,8V 8-bit, sector size 128 KiB - */ -static struct atmel_nand_data __initdata nand_data = { - .ale = 21, - .cle = 22, - .rdy_pin = AT91_PIN_PC13, - .enable_pin = AT91_PIN_PC14, -}; - -/* - * Bus timings; unit = 7.57ns - */ -static struct sam9_smc_config __initdata nand_smc_config = { - .ncs_read_setup = 0, - .nrd_setup = 2, - .ncs_write_setup = 0, - .nwe_setup = 2, - - .ncs_read_pulse = 4, - .nrd_pulse = 4, - .ncs_write_pulse = 4, - .nwe_pulse = 4, - - .read_cycle = 7, - .write_cycle = 7, - - .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE - | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8, - .tdf_cycles = 3, -}; - static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { { .ncs_read_setup = 16, .nrd_setup = 18, @@ -138,14 +100,6 @@ static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { { .tdf_cycles = 1, } }; -static void __init add_device_nand(void) -{ - /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &nand_smc_config); - at91_add_device_nand(&nand_data); -} - - static void __init add_device_pcontrol(void) { /* configure chip-select 4 (IO compatible to 8051 X4 ) */ @@ -155,23 +109,6 @@ static void __init add_device_pcontrol(void) } -/* - * MCI (SD/MMC) - * det_pin, wp_pin and vcc_pin are not connected - */ -#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) -static struct mci_platform_data __initdata mmc_data = { - .slot[0] = { - .bus_width = 4, - }, -}; -#else -static struct at91_mmc_data __initdata mmc_data = { - .wire4 = 1, -}; -#endif - - /* * USB Host port */ @@ -265,42 +202,13 @@ static struct spi_board_info pcontrol_g20_spi_devices[] = { }; -/* - * Dallas 1-Wire DS2431 - */ -static struct w1_gpio_platform_data w1_gpio_pdata = { - .pin = AT91_PIN_PA29, - .is_open_drain = 1, -}; - -static struct platform_device w1_device = { - .name = "w1-gpio", - .id = -1, - .dev.platform_data = &w1_gpio_pdata, -}; - -static void add_wire1(void) -{ - at91_set_GPIO_periph(w1_gpio_pdata.pin, 1); - at91_set_multi_drive(w1_gpio_pdata.pin, 1); - platform_device_register(&w1_device); -} - - static void __init pcontrol_g20_board_init(void) { - at91_add_device_serial(); - add_device_nand(); -#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) - at91_add_device_mci(0, &mmc_data); -#else - at91_add_device_mmc(0, &mmc_data); -#endif + stamp9g20_board_init(); at91_add_device_usbh(&usbh_data); at91_add_device_eth(&macb_data); at91_add_device_i2c(pcontrol_g20_i2c_devices, ARRAY_SIZE(pcontrol_g20_i2c_devices)); - add_wire1(); add_device_pcontrol(); at91_add_device_spi(pcontrol_g20_spi_devices, ARRAY_SIZE(pcontrol_g20_spi_devices)); -- cgit v1.2.2