Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull "ARM: More device tree support updates" from Olof Johansson:
 "This branch contains a number of updates for device tree support on
  several ARM platforms, in particular:

   * AT91 continues the device tree conversion adding support for a
     number of on-chip drivers and other functionality
   * ux500 adds probing of some of the core SoC blocks through device
     tree
   * Initial device tree support for ST SPEAr600 platforms
   * kirkwood continues the conversion to device-tree probing"

Manually merge arch/arm/mach-ux500/Kconfig due to MACH_U8500 rename, and
drivers/usb/gadget/at91_udc.c due to header file include cleanups.

Also do an "evil merge" for the MACH_U8500 config option rename that the
affected RMI4 touchscreen driver in staging.  It's called MACH_MOP500
now, and it was missed during previous merges.

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
  ARM: SPEAr600: Add device-tree support to SPEAr600 boards
  ARM: ux500: Provide local timer support for Device Tree
  ARM: ux500: Enable PL022 SSP Controller in Device Tree
  ARM: ux500: Enable PL310 Level 2 Cache Controller in Device Tree
  ARM: ux500: Enable PL011 AMBA UART Controller for Device Tree
  ARM: ux500: Enable Cortex-A9 GIC (Generic Interrupt Controller) in Device Tree
  ARM: ux500: db8500: list most devices in the snowball device tree
  ARM: ux500: split dts file for snowball into generic part
  ARM: ux500: combine the board init functions for DT boot
  ARM: ux500: Initial Device Tree support for Snowball
  ARM: ux500: CONFIG: Enable Device Tree support for future endeavours
  ARM: kirkwood: use devicetree for rtc-mv
  ARM: kirkwood: rtc-mv devicetree bindings
  ARM: kirkwood: fdt: define uart[01] as disabled, enable uart0
  ARM: kirkwood: fdt: facilitate new boards during fdt migration
  ARM: kirkwood: fdt: absorb kirkwood_init()
  ARM: kirkwood: fdt: use mrvl ticker symbol
  ARM: orion: wdt: use resource vice direct access
  ARM: Kirkwood: Remove tclk from kirkwood_asoc_platform_data.
  ARM: orion: spi: remove enable_clock_fix which is not used
  ...

8 files changed, 221 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt
index 1aeaf6f2a1ba..ecc81e368715 100644
--- a/Documentation/devicetree/bindings/arm/atmel-at91.txt
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt
@@ -30,3 +30,63 @@ One interrupt per TC channel in a TC block:
                 reg = <0xfffdc000 0x100>;
                 interrupts = <26 4 27 4 28 4>;
         };
+
+RSTC Reset Controller required properties:
+- compatible: Should be "atmel,<chip>-rstc".
+  <chip> can be "at91sam9260" or "at91sam9g45"
+- reg: Should contain registers location and length
+
+Example:
+
+        rstc@fffffd00 {
+                compatible = "atmel,at91sam9260-rstc";
+                reg = <0xfffffd00 0x10>;
+        };
+
+RAMC SDRAM/DDR Controller required properties:
+- compatible: Should be "atmel,at91sam9260-sdramc",
+                        "atmel,at91sam9g45-ddramc",
+- reg: Should contain registers location and length
+  For at91sam9263 and at91sam9g45 you must specify 2 entries.
+
+Examples:
+
+        ramc0: ramc@ffffe800 {
+                compatible = "atmel,at91sam9g45-ddramc";
+                reg = <0xffffe800 0x200>;
+        };
+
+        ramc0: ramc@ffffe400 {
+                compatible = "atmel,at91sam9g45-ddramc";
+                reg = <0xffffe400 0x200
+                       0xffffe600 0x200>;
+        };
+
+SHDWC Shutdown Controller
+
+required properties:
+- compatible: Should be "atmel,<chip>-shdwc".
+  <chip> can be "at91sam9260", "at91sam9rl" or "at91sam9x5".
+- reg: Should contain registers location and length
+
+optional properties:
+- atmel,wakeup-mode: String, operation mode of the wakeup mode.
+  Supported values are: "none", "high", "low", "any".
+- atmel,wakeup-counter: Counter on Wake-up 0 (between 0x0 and 0xf).
+
+optional at91sam9260 properties:
+- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up.
+
+optional at91sam9rl properties:
+- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up.
+- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up.
+
+optional at91sam9x5 properties:
+- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up.
+
+Example:
+
+        rstc@fffffd00 {
+                compatible = "atmel,at91sam9260-rstc";
+                reg = <0xfffffd00 0x10>;
+        };
diff --git a/Documentation/devicetree/bindings/arm/atmel-pmc.txt b/Documentation/devicetree/bindings/arm/atmel-pmc.txt
new file mode 100644
index 000000000000..389bed5056e8
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/atmel-pmc.txt
@@ -0,0 +1,11 @@
+* Power Management Controller (PMC)
+
+Required properties:
+- compatible: Should be "atmel,at91rm9200-pmc"
+- reg: Should contain PMC registers location and length
+
+Examples:
+        pmc: pmc@fffffc00 {
+                compatible = "atmel,at91rm9200-pmc";
+                reg = <0xfffffc00 0x100>;
+        };
diff --git a/Documentation/devicetree/bindings/arm/spear.txt b/Documentation/devicetree/bindings/arm/spear.txt
new file mode 100644
index 000000000000..f8e54f092328
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/spear.txt
@@ -0,0 +1,8 @@
+ST SPEAr Platforms Device Tree Bindings
+---------------------------------------
+
+Boards with the ST SPEAr600 SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "st,spear600";
diff --git a/Documentation/devicetree/bindings/gpio/gpio_i2c.txt b/Documentation/devicetree/bindings/gpio/gpio_i2c.txt
new file mode 100644
index 000000000000..4f8ec947c6bd
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio_i2c.txt
@@ -0,0 +1,32 @@
+Device-Tree bindings for i2c gpio driver
+
+Required properties:
+        - compatible = "i2c-gpio";
+        - gpios: sda and scl gpio
+
+
+Optional properties:
+        - i2c-gpio,sda-open-drain: sda as open drain
+        - i2c-gpio,scl-open-drain: scl as open drain
+        - i2c-gpio,scl-output-only: scl as output only
+        - i2c-gpio,delay-us: delay between GPIO operations (may depend on each platform)
+        - i2c-gpio,timeout-ms: timeout to get data
+
+Example nodes:
+
+i2c@0 {
+        compatible = "i2c-gpio";
+        gpios = <&pioA 23 0 /* sda */
+                 &pioA 24 0 /* scl */
+                >;
+        i2c-gpio,sda-open-drain;
+        i2c-gpio,scl-open-drain;
+        i2c-gpio,delay-us = <2>;        /* ~100 kHz */
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        rv3029c2@56 {
+                compatible = "rv3029c2";
+                reg = <0x56>;
+        };
+};
diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
new file mode 100644
index 000000000000..5903ecf6e895
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
@@ -0,0 +1,41 @@
+Atmel NAND flash
+
+Required properties:
+- compatible : "atmel,at91rm9200-nand".
+- reg : should specify localbus address and size used for the chip,
+        and if availlable the ECC.
+- atmel,nand-addr-offset : offset for the address latch.
+- atmel,nand-cmd-offset : offset for the command latch.
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+  representing partitions.
+
+- gpios : specifies the gpio pins to control the NAND device. detect is an
+  optional gpio and may be set to 0 if not present.
+
+Optional properties:
+- nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default.
+  Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
+  "soft_bch".
+- nand-bus-width : 8 or 16 bus width if not present 8
+- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
+
+Examples:
+nand0: nand@40000000,0 {
+        compatible = "atmel,at91rm9200-nand";
+        #address-cells = <1>;
+        #size-cells = <1>;
+        reg = <0x40000000 0x10000000
+               0xffffe800 0x200
+              >;
+        atmel,nand-addr-offset = <21>;
+        atmel,nand-cmd-offset = <22>;
+        nand-on-flash-bbt;
+        nand-ecc-mode = "soft";
+        gpios = <&pioC 13 0
+                 &pioC 14 0
+                 0
+                >;
+        partition@0 {
+                ...
+        };
+};
diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt
new file mode 100644
index 000000000000..03855c8c492a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/nand.txt
@@ -0,0 +1,7 @@
+* MTD generic binding
+
+- nand-ecc-mode : String, operation mode of the NAND ecc mode.
+  Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
+  "soft_bch".
+- nand-bus-width : 8 or 16 bus width if not present 8
+- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt
new file mode 100644
index 000000000000..60bd2150a3e6
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt
@@ -0,0 +1,49 @@
+Atmel SOC USB controllers
+
+OHCI
+
+Required properties:
+ - compatible: Should be "atmel,at91rm9200-ohci" for USB controllers
+   used in host mode.
+ - num-ports: Number of ports.
+ - atmel,vbus-gpio: If present, specifies a gpio that needs to be
+   activated for the bus to be powered.
+ - atmel,oc-gpio: If present, specifies a gpio that needs to be
+   activated for the overcurrent detection.
+
+usb0: ohci@00500000 {
+        compatible = "atmel,at91rm9200-ohci", "usb-ohci";
+        reg = <0x00500000 0x100000>;
+        interrupts = <20 4>;
+        num-ports = <2>;
+};
+
+EHCI
+
+Required properties:
+ - compatible: Should be "atmel,at91sam9g45-ehci" for USB controllers
+   used in host mode.
+
+usb1: ehci@00800000 {
+        compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
+        reg = <0x00800000 0x100000>;
+        interrupts = <22 4>;
+};
+
+AT91 USB device controller
+
+Required properties:
+ - compatible: Should be "atmel,at91rm9200-udc"
+ - reg: Address and length of the register set for the device
+ - interrupts: Should contain macb interrupt
+
+Optional properties:
+ - atmel,vbus-gpio: If present, specifies a gpio that needs to be
+   activated for the bus to be powered.
+
+usb1: gadget@fffa4000 {
+        compatible = "atmel,at91rm9200-udc";
+        reg = <0xfffa4000 0x4000>;
+        interrupts = <10 4>;
+        atmel,vbus-gpio = <&pioC 5 0>;
+};
diff --git a/Documentation/devicetree/bindings/usb/tegra-usb.txt b/Documentation/devicetree/bindings/usb/tegra-usb.txt
index 035d63d5646d..007005ddbe12 100644
--- a/Documentation/devicetree/bindings/usb/tegra-usb.txt
+++ b/Documentation/devicetree/bindings/usb/tegra-usb.txt
@@ -11,3 +11,16 @@ Required properties :
  - phy_type : Should be one of "ulpi" or "utmi".
  - nvidia,vbus-gpio : If present, specifies a gpio that needs to be
    activated for the bus to be powered.
+
+Optional properties:
+  - dr_mode : dual role mode. Indicates the working mode for
+   nvidia,tegra20-ehci compatible controllers.  Can be "host", "peripheral",
+   or "otg".  Default to "host" if not defined for backward compatibility.
+      host means this is a host controller
+      peripheral means it is device controller
+      otg means it can operate as either ("on the go")
+  - nvidia,has-legacy-mode : boolean indicates whether this controller can
+    operate in legacy mode (as APX 2500 / 2600). In legacy mode some
+    registers are accessed through the APB_MISC base address instead of
+    the USB controller. Since this is a legacy issue it probably does not
+    warrant a compatible string of its own.