#ifndef __LINUX_USB_H
#define __LINUX_USB_H
#include <linux/mod_devicetable.h>
#include <linux/usb/ch9.h>
#define USB_MAJOR 180
#define USB_DEVICE_MAJOR 189
#ifdef __KERNEL__
#include <linux/errno.h> /* for -ENODEV */
#include <linux/delay.h> /* for mdelay() */
#include <linux/interrupt.h> /* for in_interrupt() */
#include <linux/list.h> /* for struct list_head */
#include <linux/kref.h> /* for struct kref */
#include <linux/device.h> /* for struct device */
#include <linux/fs.h> /* for struct file_operations */
#include <linux/completion.h> /* for struct completion */
#include <linux/sched.h> /* for current && schedule_timeout */
#include <linux/mutex.h> /* for struct mutex */
#include <linux/pm_runtime.h> /* for runtime PM */
struct usb_device;
struct usb_driver;
struct wusb_dev;
/*-------------------------------------------------------------------------*/
/*
* Host-side wrappers for standard USB descriptors ... these are parsed
* from the data provided by devices. Parsing turns them from a flat
* sequence of descriptors into a hierarchy:
*
* - devices have one (usually) or more configs;
* - configs have one (often) or more interfaces;
* - interfaces have one (usually) or more settings;
* - each interface setting has zero or (usually) more endpoints.
* - a SuperSpeed endpoint has a companion descriptor
*
* And there might be other descriptors mixed in with those.
*
* Devices may also have class-specific or vendor-specific descriptors.
*/
struct ep_device;
/**
* struct usb_host_endpoint - host-side endpoint descriptor and queue
* @desc: descriptor for this endpoint, wMaxPacketSize in native byteorder
* @ss_ep_comp: SuperSpeed companion descriptor for this endpoint
* @urb_list: urbs queued to this endpoint; maintained by usbcore
* @hcpriv: for use by HCD; typically holds hardware dma queue head (QH)
* with one or more transfer descriptors (TDs) per urb
* @ep_dev: ep_device for sysfs info
* @extra: descriptors following this endpoint in the configuration
* @extralen: how many bytes of "extra" are valid
* @enabled: URBs may be submitted to this endpoint
*
* USB requests are always queued to a given endpoint, identified by a
* descriptor within an active interface in a given USB configuration.
*/
struct usb_host_endpoint {
struct usb_endpoint_descriptor desc;
struct usb_ss_ep_comp_descriptor ss_ep_comp;
struct list_head urb_list;
void *hcpriv;
struct ep_device *ep_dev; /* For sysfs info */
unsigned char *extra; /* Extra descriptors */
int extralen;
int enabled;
};
/* host-side wrapper for one interface setting's parsed descriptors */
struct usb_host_interface {
struct usb_interface_descriptor desc;
/* array of desc.bNumEndpoint endpoints associated with this
* interface setting. these will be in no particular order.
*/
struct usb_host_endpoint *endpoint;
char *string; /* iInterface string, if present */
unsigned char *extra; /* Extra descriptors */
int extralen;
};
enum usb_interface_condition {
USB_INTERFACE_UNBOUND = 0,
USB_INTERFACE_BINDING,
USB_INTERFACE_BOUND,
USB_INTERFACE_UNBINDING,
};
/**
* struct usb_interface - what usb device drivers talk to
* @altsetting: array of interface structures, one for each alternate
* setting that may be selected. Each one includes a set of
* endpoint configurations. They will be in no particular order.
* @cur_altsetting: the current altsetting.
* @num_altsetting: number of altsettings defined.
* @intf_assoc: interface association descriptor
* @minor: the minor number assigned to this interface, if this
* interface is bound to a driver that uses the USB major number.
* If this interface does not use the USB major, this field should
* be unused. The driver should set this value in the probe()
* function of the driver, after it has been assigned a minor
* number from the USB core by calling usb_register_dev().
* @condition: binding state of the interface: not bound, binding
* (in probe()), bound to a driver, or unbinding (in disconnect())
* @sysfs_files_created: sysfs attributes exist
* @ep_devs_created: endpoint child pseudo-devices exist
* @unregistering: flag set when the interface is being unregistered
* @needs_remote_wakeup: flag set when the driver requires remote-wakeup
* capability during autosuspend.
* @needs_altsetting0: flag set when a set-interface request for altsetting 0
* has been deferred.
* @needs_binding: flag set when the driver should be re-probed or unbound
* following a reset or suspend operation it doesn't support.
* @dev: driver model's view of this device
* @usb_dev: if an interface is bound to the USB major, this will point
* to the sysfs representation for that device.
* @pm_usage_cnt: PM usage counter for this interface
* @reset_ws: Used for scheduling resets from atomic context.
* @reset_running: set to 1 if the interface is currently running a
* queued reset so that usb_cancel_queued_reset() doesn't try to
* remove from the workqueue when running inside the worker
* thread. See __usb_queue_reset_device().
* @resetting_device: USB core reset the device, so use alt setting 0 as
* current; needs bandwidth alloc after reset.
*
* USB device drivers attach to interfaces on a physical device. Each
* interface encapsulates a single high level function, such as feeding
* an audio stream to a speaker or reporting a change in a volume control.
* Many USB devices only have one interface. The protocol used to talk to
* an interface's endpoints can be defined in a usb "class" specification,
* or by a product's vendor. The (default) control endpoint is part of
* every interface, but is never listed among the interface's descriptors.
*
* The driver that is bound to the interface can use standard driver model
* calls such as dev_get_drvdata() on the dev member of this structure.
*
* Each interface may have alternate settings. The initial configuration
* of a device sets altsetting 0, but the device driver can change
* that setting using usb_set_interface(). Alternate settings are often
* used to control the use of periodic endpoints, such as by having
* different endpoints use different amounts of reserved USB bandwidth.
* All standards-conformant USB devices that use isochronous endpoints
* will use them in non-default settings.
*
* The USB specification says that alternate setting numbers must run from
* 0 to one less than the total number of alternate settings. But some
* devices manage to mess this up, and the structures aren't necessarily
* stored in numerical order anyhow. Use usb_altnum_to_altsetting() to
* look up an alternate setting in the altsetting array based on its number.
*/
struct usb_interface {
/* array of alternate settings for this interface,
* stored in no particular order */
struct usb_host_interface *altsetting;
struct usb_host_interface *cur_altsetting; /* the currently
* active alternate setting */
unsigned num_altsetting; /* number of alternate settings */
/* If there is an interface association descriptor then it will list
* the associated interfaces */
struct usb_interface_assoc_descriptor *intf_assoc;
int minor; /* minor number this interface is
* bound to */
enum usb_interface_condition condition; /* state of binding */
unsigned sysfs_files_created:1; /* the sysfs attributes exist */
unsigned ep_devs_created:1; /* endpoint "devices" exist */
unsigned unregistering:1; /* unregistration is in progress */
unsigned needs_remote_wakeup:1; /* driver requires remote wakeup */
unsigned needs_altsetting0:1; /* switch to altsetting 0 is pending */
unsigned needs_binding:1; /* needs delayed unbind/rebind */
unsigned reset_running:1;
unsigned resetting_device:1; /* true: bandwidth alloc after reset */
struct device dev; /* interface specific device info */
struct device *usb_dev;
atomic_t pm_usage_cnt; /* usage counter for autosuspend */
struct work_struct reset_ws; /* for resets in atomic context */
};
#define to_usb_interface(d) container_of(d, struct usb_interface, dev)
static inline void *usb_get_intfdata(struct usb_interface *intf)
{
return dev_get_drvdata(&intf->dev);
}
static inline void usb_set_intfdata(struct usb_interface *intf, void *data)
{
dev_set_drvdata(&intf->dev, data);
}
struct usb_interface *usb_get_intf(struct usb_interface *intf);
void usb_put_intf(struct usb_interface *intf);
/* this maximum is arbitrary */
#define USB_MAXINTERFACES 32
#define USB_MAXIADS (USB_MAXINTERFACES/2)
/**
* struct usb_interface_cache - long-term representation of a device interface
* @num_altsetting: number of altsettings defined.
* @ref: reference counter.
* @altsetting: variable-length array of interface structures, one for
* each alternate setting that may be selected. Each one includes a
* set of endpoint configurations. They will be in no particular order.
*
* These structures persist for the lifetime of a usb_device, unlike
* struct usb_interface (which persists only as long as its configuration
* is installed). The altsetting arrays can be accessed through these
* structures at any time, permitting comparison of configurations and
* providing support for the /proc/bus/usb/devices pseudo-file.
*/
struct usb_interface_cache {
unsigned num_altsetting; /* number of alternate settings */
struct kref ref; /* reference counter */
/* variable-length array of alternate settings for this interface,
* stored in no particular order */
struct usb_host_interface altsetting[0];
};
#define ref_to_usb_interface_cache(r) \
container_of(r, struct usb_interface_cache, ref)
#define altsetting_to_usb_interface_cache(a) \
container_of(a, struct usb_interface_cache, altsetting[0])
/**
* struct usb_host_config - representation of a device's configuration
* @desc: the device's configuration descriptor.
* @string: pointer to the cached version of the iConfiguration string, if
* present for this configuration.
* @intf_assoc: list of any interface association descriptors in this config
* @interface: array of pointers to usb_interface structures, one for each
* interface in the configuration. The number of interfaces is stored
* in desc.bNumInterfaces. These pointers are valid only while the
* the configuration is active.
* @intf_cache: array of pointers to usb_interface_cache structures, one
* for each interface in the configuration. These structures exist
* for the entire life of the device.
* @extra: pointer to buffer containing all extra descriptors associated
* with this configuration (those preceding the first interface
* descriptor).
* @extralen: length of the extra descriptors buffer.
*
* USB devices may have multiple configurations, but only one can be active
* at any time. Each encapsulates a different operational environment;
* for example, a dual-speed device would have separate configurations for
* full-speed and high-speed operation. The number of configurations
* available is stored in the device descriptor as bNumConfigurations.
*
* A configuration can contain multiple interfaces. Each corresponds to
* a different function of the USB device, and all are available whenever
* the configuration is active. The USB standard says that interfaces
* are supposed to be numbered from 0 to desc.bNumInterfaces-1, but a lot
* of devices get this wrong. In addition, the interface array is not
* guaranteed to be sorted in numerical order. Use usb_ifnum_to_if() to
* look up an interface entry based on its number.
*
* Device drivers should not attempt to activate configurations. The choice
* of which configuration to install is a policy decision based on such
* considerations as available power, functionality provided, and the user's
* desires (expressed through userspace tools). However, drivers can call
* usb_reset_configuration() to reinitialize the current configuration and
* all its interfaces.
*/
struct usb_host_config {
struct usb_config_descriptor desc;
char *string; /* iConfiguration string, if present */
/* List of any Interface Association Descriptors in this
* configuration. */
struct usb_interface_assoc_descriptor *intf_assoc[USB_MAXIADS];
/* the interfaces associated with this configuration,
* stored in no particular order */
struct usb_interface *interface[USB_MAXINTERFACES];
/* Interface information available even when this is not the
* active configuration */
struct usb_interface_cache *intf_cache[USB_MAXINTERFACES];
unsigned char *extra; /* Extra descriptors */
int extralen;
};
/* USB2.0 and USB3.0 device BOS descriptor set */
struct usb_host_bos {
struct usb_bos_descriptor *desc;
/* wireless cap descriptor is handled by wusb */
struct usb_ext_cap_descriptor *ext_cap;
struct usb_ss_cap_descriptor *ss_cap;
struct usb_ss_container_id_descriptor *ss_id;
};
int __usb_get_extra_descriptor(char *buffer, unsigned size,
unsigned char type, void **ptr);
#define usb_get_extra_descriptor(ifpoint, type, ptr) \
__usb_get_extra_descriptor((ifpoint)->extra, \
(ifpoint)->extralen, \
type, (void **)ptr)
/* ----------------------------------------------------------------------- */
/* USB device number allocation bitmap */
struct usb_devmap {
unsigned long devicemap[128 / (8*sizeof(unsigned long))];
};
/*
* Allocated per bus (tree of devices) we have:
*/
struct usb_bus {
struct device *controller; /* host/master side hardware */
int busnum; /* Bus number (in order of reg) */
const char *bus_name; /* stable id (PCI slot_name etc) */
u8 uses_dma; /* Does the host controller use DMA? */
u8 uses_pio_for_control; /*
* Does the host controller use PIO
* for control transfers?
*/
u8 otg_port; /* 0, or number of OTG/HNP port */
unsigned is_b_host:1; /* true during some HNP roleswitches */
unsigned b_hnp_enable:1; /* OTG: did A-Host enable HNP? */
unsigned sg_tablesize; /* 0 or largest number of sg list entries */
int devnum_next; /* Next open device number in
* round-robin allocation */
struct usb_devmap devmap; /* device address allocation map */
struct usb_device *root_hub; /* Root hub */
struct usb_bus *hs_companion; /* Companion EHCI bus, if any */
struct list_head bus_list; /* list of busses */
int bandwidth_allocated; /* on this bus: how much of the time
* reserved for periodic (intr/iso)
* requests is used, on average?
* Units: microseconds/frame.
* Limits: Full/low speed reserve 90%,
* while high speed reserves 80%.
*/
int bandwidth_int_reqs; /* number of Interrupt requests */
int bandwidth_isoc_reqs; /* number of Isoc. requests */
#ifdef CONFIG_USB_DEVICEFS
struct dentry *usbfs_dentry; /* usbfs dentry entry for the bus */
#endif
#if defined(CONFIG_USB_MON) || defined(CONFIG_USB_MON_MODULE)
struct mon_bus *mon_bus; /* non-null when associated */
int monitored; /* non-zero when monitored */
#endif
};
/* ----------------------------------------------------------------------- */
/* This is arbitrary.
* From USB 2.0 spec Table 11-13, offset 7, a hub can
* have up to 255 ports. The most yet reported is 10.
*
* Current Wireless USB host hardware (Intel i1480 for example) allows
* up to 22 devices to connect. Upcoming hardware might raise that
* limit. Because the arrays need to add a bit for hub status data, we
* do 31, so plus one evens out to four bytes.
*/
#define USB_MAXCHILDREN (31)
struct usb_tt;
/**
* struct usb_device - kernel's representation of a USB device
* @devnum: device number; address on a USB bus
* @devpath: device ID string for use in messages (e.g., /port/...)
* @route: tree topology hex string for use with xHCI
* @state: device state: configured, not attached, etc.
* @speed: device speed: high/full/low (or error)
* @tt: Transaction Translator info; used with low/full speed dev, highspeed hub
* @ttport: device port on that tt hub
* @toggle: one bit for each endpoint, with ([0] = IN, [1] = OUT) endpoints
* @parent: our hub, unless we're the root
* @bus: bus we're part of
* @ep0: endpoint 0 data (default control pipe)
* @dev: generic device interface
* @descriptor: USB device descriptor
* @bos: USB device BOS descriptor set
* @config: all of the device's configs
* @actconfig: the active configuration
* @ep_in: array of IN endpoints
* @ep_out: array of OUT endpoints
* @rawdescriptors: raw descriptors for each config
* @bus_mA: Current available from the bus
* @portnum: parent port number (origin 1)
* @level: number of USB hub ancestors
* @can_submit: URBs may be submitted
* @persist_enabled: USB_PERSIST enabled for this device
* @have_langid: whether string_langid is valid
* @authorized: policy has said we can use it;
* (user space) policy determines if we authorize this device to be
* used or not. By default, wired USB devices are authorized.
* WUSB devices are not, until we authorize them from user space.
* FIXME -- complete doc
* @authenticated: Crypto authentication passed
* @wusb: device is Wireless USB
* @lpm_capable: device supports LPM
* @usb2_hw_lpm_capable: device can perform USB2 hardware LPM
* @usb2_hw_lpm_enabled: USB2 hardware LPM enabled
* @string_langid: language ID for strings
* @product: iProduct string, if present (static)
* @manufacturer: iManufacturer string, if present (static)
* @serial: iSerialNumber string, if present (static)
* @filelist: usbfs files that are open to this device
* @usb_classdev: USB class device that was created for usbfs device
* access from userspace
* @usbfs_dentry: usbfs dentry entry for the device
* @maxchild: number of ports if hub
* @children: child devices - USB devices that are attached to this hub
* @quirks: quirks of the whole device
* @urbnum: number of URBs submitted for the whole device
* @active_duration: total time device is not suspended
* @connect_time: time device was first connected
* @do_remote_wakeup: remote wakeup should be enabled
* @reset_resume: needs reset instead of resume
* @wusb_dev: if this is a Wireless USB device, link to the WUSB
* specific data for the device.
* @slot_id: Slot ID assigned by xHCI
*
* Notes:
* Usbcore drivers should not set usbdev->state directly. Instead use
* usb_set_device_state().
*/
struct usb_device {
int devnum;
char devpath[16];
u32 route;
enum usb_device_state state;
enum usb_device_speed speed;
struct usb_tt *tt;
int ttport;
unsigned int toggle[2];
struct usb_device *parent;
struct usb_bus *bus;
struct usb_host_endpoint ep0;
struct device dev;
struct usb_device_descriptor descriptor;
struct usb_host_bos *bos;
struct usb_host_config *config;
struct usb_host_config *actconfig;
struct usb_host_endpoint *ep_in[16];
struct usb_host_endpoint *ep_out[16];
char **rawdescriptors;
unsigned short bus_mA;
u8 portnum;
u8 level;
unsigned can_submit:1;
unsigned persist_enabled:1;
unsigned have_langid:1;
unsigned authorized:1;
unsigned authenticated:1;
unsigned wusb:1;
unsigned lpm_capable:1;
unsigned usb2_hw_lpm_capable:1;
unsigned usb2_hw_lpm_enabled:1;
int string_langid;
/* static strings from the device */
char *product;
char *manufacturer;
char *serial;
struct list_head filelist;
#ifdef CONFIG_USB_DEVICE_CLASS
struct device *usb_classdev;
#endif
#ifdef CONFIG_USB_DEVICEFS
struct dentry *usbfs_dentry;
#endif
int maxchild;
struct usb_device *children[USB_MAXCHILDREN];
u32 quirks;
atomic_t urbnum;
unsigned long active_duration;
#ifdef CONFIG_PM
unsigned long connect_time;
unsigned do_remote_wakeup:1;
unsigned reset_resume:1;
#endif
struct wusb_dev *wusb_dev;
int slot_id;
};
#define to_usb_device(d) container_of(d, struct usb_device, dev)
static inline struct usb_device *interface_to_usbdev(struct usb_interface *intf)
{
return to_usb_device(intf->dev.parent);
}
extern struct usb_device *usb_get_dev(struct usb_device *dev);
extern void usb_put_dev(struct usb_device *dev);
/* USB device locking */
#define usb_lock_device(udev) device_lock(&(udev)->dev)
#define usb_unlock_device(udev) device_unlock(&(udev)->dev)
#define usb_trylock_device(udev) device_trylock(&(udev)->dev)
extern int usb_lock_device_for_reset(struct usb_device *udev,
const struct usb_interface *iface);
/* USB port reset for device reinitialization */
extern int usb_reset_device(struct usb_device *dev);
extern void usb_queue_reset_device(struct usb_interface *dev);
/* USB autosuspend and autoresume */
#ifdef CONFIG_USB_SUSPEND
extern void usb_enable_autosuspend(struct usb_device *udev);
extern void usb_disable_autosuspend(struct usb_device *udev);
extern int usb_autopm_get_interface(struct usb_interface *intf);
extern void usb_autopm_put_interface(struct usb_interface *intf);
extern int usb_autopm_get_interface_async(struct usb_interface *intf);
extern void usb_autopm_put_interface_async(struct usb_interface *intf);
extern void usb_autopm_get_interface_no_resume(struct usb_interface *intf);
extern void usb_autopm_put_interface_no_suspend(struct usb_interface *intf);
static inline void usb_mark_last_busy(struct usb_device *udev)
{
pm_runtime_mark_last_busy(&udev->dev);
}
#else
static inline int usb_enable_autosuspend(struct usb_device *udev)
{ return 0; }
static inline int usb_disable_autosuspend(struct usb_device *udev)
{ return 0; }
static inline int usb_autopm_get_interface(struct usb_interface *intf)
{ return 0; }
static inline int usb_autopm_get_interface_async(struct usb_interface *intf)
{ return 0; }
static inline void usb_autopm_put_interface(struct usb_interface *intf)
{ }
static inline void usb_autopm_put_interface_async(struct usb_interface *intf)
{ }
static inline void usb_autopm_get_interface_no_resume(
struct usb_interface *intf)
{ }
static inline void usb_autopm_put_interface_no_suspend(
struct usb_interface *intf)
{ }
static inline void usb_mark_last_busy(struct usb_device *udev)
{ }
#endif
/*-------------------------------------------------------------------------*/
/* for drivers using iso endpoints */
extern int usb_get_current_frame_number(struct usb_device *usb_dev);
/* Sets up a group of bulk endpoints to support multiple stream IDs. */
extern int usb_alloc_streams(struct usb_interface *interface,
struct usb_host_endpoint **eps, unsigned int num_eps,
unsigned int num_streams, gfp_t mem_flags);
/* Reverts a group of bulk endpoints back to not using stream IDs. */
extern void usb_free_streams(struct usb_interface *interface,
struct usb_host_endpoint **eps, unsigned int num_eps,
gfp_t mem_flags);
/* used these for multi-interface device registration */
extern int usb_driver_claim_interface(struct usb_driver *driver,
struct usb_interface *iface, void *priv);
/**
* usb_interface_claimed - returns true iff an interface is claimed
* @iface: the interface being checked
*
* Returns true (nonzero) iff the interface is claimed, else false (zero).
* Callers must own the driver model's usb bus readlock. So driver
* probe() entries don't need extra locking, but other call contexts
* may need to explicitly claim that lock.
*
*/
static inline int usb_interface_claimed(struct usb_interface *iface)
{
return (iface->dev.driver != NULL);
}
extern void usb_driver_release_interface(struct usb_driver *driver,
struct usb_interface *iface);
const struct usb_device_id *usb_match_id(struct usb_interface *interface,
const struct usb_device_id *id);
extern int usb_match_one_id(struct usb_interface *interface,
const struct usb_device_id *id);
extern struct usb_interface *usb_find_interface(struct usb_driver *drv,
int minor);
extern struct usb_interface *usb_ifnum_to_if(const struct usb_device *dev,
unsigned ifnum);
extern struct usb_host_interface *usb_altnum_to_altsetting(
const struct usb_interface *intf, unsigned int altnum);
extern struct usb_host_interface *usb_find_alt_setting(
struct usb_host_config *config,
unsigned int iface_num,
unsigned int alt_num);
/**
* usb_make_path - returns stable device path in the usb tree
* @dev: the device whose path is being constructed
* @buf: where to put the string
* @size: how big is "buf"?
*
* Returns length of the string (> 0) or negative if size was too small.
*
* This identifier is intended to be "stable", reflecting physical paths in
* hardware such as physical bus addresses for host controllers or ports on
* USB hubs. That makes it stay the same until systems are physically
* reconfigured, by re-cabling a tree of USB devices or by moving USB host
* controllers. Adding and removing devices, including virtual root hubs
* in host controller driver modules, does not change these path identifiers;
* neither does rebooting or re-enumerating. These are more useful identifiers
* than changeable ("unstable") ones like bus numbers or device addresses.
*
* With a partial exception for devices connected to USB 2.0 root hubs, these
* identifiers are also predictable. So long as the device tree isn't changed,
* plugging any USB device into a given hub port always gives it the same path.
* Because of the use of "companion" controllers, devices connected to ports on
* USB 2.0 root hubs (EHCI host controllers) will get one path ID if they are
* high speed, and a different one if they are full or low speed.
*/
static inline int usb_make_path(struct usb_device *dev, char *buf, size_t size)
{
int actual;
actual = snprintf(buf, size, "usb-%s-%s", dev->bus->bus_name,
dev->devpath);
return (actual >= (int)size) ? -1 : actual;
}
/*-------------------------------------------------------------------------*/
#define USB_DEVICE_ID_MATCH_DEVICE \
(USB_DEVICE_ID_MATCH_VENDOR | USB_DEVICE_ID_MATCH_PRODUCT)
#define USB_DEVICE_ID_MATCH_DEV_RANGE \
(USB_DEVICE_ID_MATCH_DEV_LO | USB_DEVICE_ID_MATCH_DEV_HI)
#define USB_DEVICE_ID_MATCH_DEVICE_AND_VERSION \
(USB_DEVICE_ID_MATCH_DEVICE | USB_DEVICE_ID_MATCH_DEV_RANGE)
#define USB_DEVICE_ID_MATCH_DEV_INFO \
(USB_DEVICE_ID_MATCH_DEV_CLASS | \
USB_DEVICE_ID_MATCH_DEV_SUBCLASS | \
USB_DEVICE_ID_MATCH_DEV_PROTOCOL)
#define USB_DEVICE_ID_MATCH_INT_INFO \
(USB_DEVICE_ID_MATCH_INT_CLASS | \
USB_DEVICE_ID_MATCH_INT_SUBCLASS | \
USB_DEVICE_ID_MATCH_INT_PROTOCOL)
/**
* USB_DEVICE - macro used to describe a specific usb device
* @vend: the 16 bit USB Vendor ID
* @prod: the 16 bit USB Product ID
*
* This macro is used to create a struct usb_device_id that matches a
* specific device.
*/
#define USB_DEVICE(vend, prod) \
.match_flags = USB_DEVICE_ID_MATCH_DEVICE, \
.idVendor = (vend), \
.idProduct = (prod)
/**
* USB_DEVICE_VER - describe a specific usb device with a version range
* @vend: the 16 bit USB Vendor ID
* @prod: the 16 bit USB Product ID
* @lo: the bcdDevice_lo value
* @hi: the bcdDevice_hi value
*
* This macro is used to create a struct usb_device_id that matches a
* specific device, with a version range.
*/
#define USB_DEVICE_VER(vend, prod, lo, hi) \
.match_flags = USB_DEVICE_ID_MATCH_DEVICE_AND_VERSION, \
.idVendor = (vend), \
.idProduct = (prod), \
.bcdDevice_lo = (lo), \
.bcdDevice_hi = (hi)
/**
* USB_DEVICE_INTERFACE_PROTOCOL - describe a usb device with a specific interface protocol
* @vend: the 16 bit USB Vendor ID
* @prod: the 16 bit USB Product ID
* @pr: bInterfaceProtocol value
*
* This macro is used to create a struct usb_device_id that matches a
* specific interface protocol of devices.
*/
#define USB_DEVICE_INTERFACE_PROTOCOL(vend, prod, pr) \
.match_flags = USB_DEVICE_ID_MATCH_DEVICE | \
USB_DEVICE_ID_MATCH_INT_PROTOCOL, \
.idVendor = (vend), \
.idProduct = (prod), \
.bInterfaceProtocol = (pr)
/**
* USB_DEVICE_INFO - macro used to describe a class of usb devices
* @cl: bDeviceClass value
* @sc: bDeviceSubClass value
* @pr: bDeviceProtocol value
*
* This macro is used to create a struct usb_device_id that matches a
* specific class of devices.
*/
#define USB_DEVICE_INFO(cl, sc, pr) \
.match_flags = USB_DEVICE_ID_MATCH_DEV_INFO, \
.bDeviceClass = (cl), \
.bDeviceSubClass = (sc), \
.bDeviceProtocol = (pr)
/**
* USB_INTERFACE_INFO - macro used to describe a class of usb interfaces
* @cl: bInterfaceClass value
* @sc: bInterfaceSubClass value
* @pr: bInterfaceProtocol value
*
* This macro is used to create a struct usb_device_id that matches a
* specific class of interfaces.
*/
#define USB_INTERFACE_INFO(cl, sc, pr) \
.match_flags = USB_DEVICE_ID_MATCH_INT_INFO, \
.bInterfaceClass = (cl), \
.bInterfaceSubClass = (sc), \
.bInterfaceProtocol = (pr)
/**
* USB_DEVICE_AND_INTERFACE_INFO - describe a specific usb device with a class of usb interfaces
* @vend: the 16 bit USB Vendor ID
* @prod: the 16 bit USB Product ID
* @cl: bInterfaceClass value
* @sc: bInterfaceSubClass value
* @pr: bInterfaceProtocol value
*
* This macro is used to create a struct usb_device_id that matches a
* specific device with a specific class of interfaces.
*
* This is especially useful when explicitly matching devices that have
* vendor specific bDeviceClass values, but standards-compliant interfaces.
*/
#define USB_DEVICE_AND_INTERFACE_INFO(vend, prod, cl, sc, pr) \
.match_flags = USB_DEVICE_ID_MATCH_INT_INFO \
| USB_DEVICE_ID_MATCH_DEVICE, \
.idVendor = (vend), \
.idProduct = (prod), \
.bInterfaceClass = (cl), \
.bInterfaceSubClass = (sc), \
.bInterfaceProtocol = (pr)
/* ----------------------------------------------------------------------- */
/* Stuff for dynamic usb ids */
struct usb_dynids {
spinlock_t lock;
struct list_head list;
};
struct usb_dynid {
struct list_head node;
struct usb_device_id id;
};
extern ssize_t usb_store_new_id(struct usb_dynids *dynids,
struct device_driver *driver,
const char *buf, size_t count);
/**
* struct usbdrv_wrap - wrapper for driver-model structure
* @driver: The driver-model core driver structure.
* @for_devices: Non-zero for device drivers, 0 for interface drivers.
*/
struct usbdrv_wrap {
struct device_driver driver;
int for_devices;
};
/**
* struct usb_driver - identifies USB interface driver to usbcore
* @name: The driver name should be unique among USB drivers,
* and should normally be the same as the module name.
* @probe: Called to see if the driver is willing to manage a particular
* interface on a device. If it is, probe returns zero and uses
* usb_set_intfdata() to associate driver-specific data with the
* interface. It may also use usb_set_interface() to specify the
* appropriate altsetting. If unwilling to manage the interface,
* return -ENODEV, if genuine IO errors occurred, an appropriate
* negative errno value.
* @disconnect: Called when the interface is no longer accessible, usually
* because its device has been (or is being) disconnected or the
* driver module is being unloaded.
* @unlocked_ioctl: Used for drivers that want to talk to userspace through
* the "usbfs" filesystem. This lets devices provide ways to
* expose information to user space regardless of where they
* do (or don't) show up otherwise in the filesystem.
* @suspend: Called when the device is going to be suspended by the system.
* @resume: Called when the device is being resumed by the system.
* @reset_resume: Called when the suspended device has been reset instead
* of being resumed.
* @pre_reset: Called by usb_reset_device() when the device is about to be
* reset. This routine must not return until the driver has no active
* URBs for the device, and no more URBs may be submitted until the
* post_reset method is called.
* @post_reset: Called by usb_reset_device() after the device
* has been reset
* @id_table: USB drivers use ID table to support hotplugging.
* Export this with MODULE_DEVICE_TABLE(usb,...). This must be set
* or your driver's probe function will never get called.
* @dynids: used internally to hold the list of dynamically added device
* ids for this driver.
* @drvwrap: Driver-model core structure wrapper.
* @no_dynamic_id: if set to 1, the USB core will not allow dynamic ids to be
* added to this driver by preventing the sysfs file from being created.
* @supports_autosuspend: if set to 0, the USB core will not allow autosuspend
* for interfaces bound to this driver.
* @soft_unbind: if set to 1, the USB core will not kill URBs and disable
* endpoints before calling the driver's disconnect method.
*
* USB interface drivers must provide a name, probe() and disconnect()
* methods, and an id_table. Other driver fields are optional.
*
* The id_table is used in hotplugging. It holds a set of descriptors,
* and specialized data may be associated with each entry. That table
* is used by both user and kernel mode hotplugging support.
*
* The probe() and disconnect() methods are called in a context where
* they can sleep, but they should avoid abusing the privilege. Most
* work to connect to a device should be done when the device is opened,
* and undone at the last close. The disconnect code needs to address
* concurrency issues with respect to open() and close() methods, as
* well as forcing all pending I/O requests to complete (by unlinking
* them as necessary, and blocking until the unlinks complete).
*/
struct usb_driver {
const char *name;
int (*probe) (struct usb_interface *intf,
const struct usb_device_id *id);
void (*disconnect) (struct usb_interface *intf);
int (*unlocked_ioctl) (struct usb_interface *intf, unsigned int code,
void *buf);
int (*suspend) (struct usb_interface *intf, pm_message_t message);
int (*resume) (struct usb_interface *intf);
int (*reset_resume)(struct usb_interface *intf);
int (*pre_reset)(struct usb_interface *intf);
int (*post_reset)(struct usb_interface *intf);
const struct usb_device_id *id_table;
struct usb_dynids dynids;
struct usbdrv_wrap drvwrap;
unsigned int no_dynamic_id:1;
unsigned int supports_autosuspend:1;
unsigned int soft_unbind:1;
};
#define to_usb_driver(d) container_of(d, struct usb_driver, drvwrap.driver)
/**
* struct usb_device_driver - identifies USB device driver to usbcore
* @name: The driver name should be unique among USB drivers,
* and should normally be the same as the module name.
* @probe: Called to see if the driver is willing to manage a particular
* device. If it is, probe returns zero and uses dev_set_drvdata()
* to associate driver-specific data with the device. If unwilling
* to manage the device, return a negative errno value.
* @disconnect: Called when the device is no longer accessible, usually
* because it has been (or is being) disconnected or the driver's
* module is being unloaded.
* @suspend: Called when the device is going to be suspended by the system.
* @resume: Called when the device is being resumed by the system.
* @drvwrap: Driver-model core structure wrapper.
* @supports_autosuspend: if set to 0, the USB core will not allow autosuspend
* for devices bound to this driver.
*
* USB drivers must provide all the fields listed above except drvwrap.
*/
struct usb_device_driver {
const char *name;
int (*probe) (struct usb_device *udev);
void (*disconnect) (struct usb_device *udev);
int (*suspend) (struct usb_device *udev, pm_message_t message);
int (*resume) (struct usb_device *udev, pm_message_t message);
struct usbdrv_wrap drvwrap;
unsigned int supports_autosuspend:1;
};
#define to_usb_device_driver(d) container_of(d, struct usb_device_driver, \
drvwrap.driver)
extern struct bus_type usb_bus_type;
/**
* struct usb_class_driver - identifies a USB driver that wants to use the USB major number
* @name: the usb class device name for this driver. Will show up in sysfs.
* @devnode: Callback to provide a naming hint for a possible
* device node to create.
* @fops: pointer to the struct file_operations of this driver.
* @minor_base: the start of the minor range for this driver.
*
* This structure is used for the usb_register_dev() and
* usb_unregister_dev() functions, to consolidate a number of the
* parameters used for them.
*/
struct usb_class_driver {
char *name;
char *(*devnode)(struct device *dev, umode_t *mode);
const struct file_operations *fops;
int minor_base;
};
/*
* use these in module_init()/module_exit()
* and don't forget MODULE_DEVICE_TABLE(usb, ...)
*/
extern int usb_register_driver(struct usb_driver *, struct module *,
const char *);
/* use a define to avoid include chaining to get THIS_MODULE & friends */
#define usb_register(driver) \
usb_register_driver(driver, THIS_MODULE, KBUILD_MODNAME)
extern void usb_deregister(struct usb_driver *);
/**
* module_usb_driver() - Helper macro for registering a USB driver
* @__usb_driver: usb_driver struct
*
* Helper macro for USB drivers which do not do anything special in module
* init/exit. This eliminates a lot of boilerplate. Each module may only
* use this macro once, and calling it replaces module_init() and module_exit()
*/
#define module_usb_driver(__usb_driver) \
module_driver(__usb_driver, usb_register, \
usb_deregister)
extern int usb_register_device_driver(struct usb_device_driver *,
struct module *);
extern void usb_deregister_device_driver(struct usb_device_driver *);
extern int usb_register_dev(struct usb_interface *intf,
struct usb_class_driver *class_driver);
extern void usb_deregister_dev(struct usb_interface *intf,
struct usb_class_driver *class_driver);
extern int usb_disabled(void);
/* ----------------------------------------------------------------------- */
/*
* URB support, for asynchronous request completions
*/
/*
* urb->transfer_flags:
*
* Note: URB_DIR_IN/OUT is automatically set in usb_submit_urb().
*/
#define URB_SHORT_NOT_OK 0x0001 /* report short reads as errors */
#define URB_ISO_ASAP 0x0002 /* iso-only, urb->start_frame
* ignored */
#define URB_NO_TRANSFER_DMA_MAP 0x0004 /* urb->transfer_dma valid on submit */
#define URB_NO_FSBR 0x0020 /* UHCI-specific */
#define URB_ZERO_PACKET 0x0040 /* Finish bulk OUT with short packet */
#define URB_NO_INTERRUPT 0x0080 /* HINT: no non-error interrupt
* needed */
#define URB_FREE_BUFFER 0x0100 /* Free transfer buffer with the URB */
/* The following flags are used internally by usbcore and HCDs */
#define URB_DIR_IN 0x0200 /* Transfer from device to host */
#define URB_DIR_OUT 0
#define URB_DIR_MASK URB_DIR_IN
#define URB_DMA_MAP_SINGLE 0x00010000 /* Non-scatter-gather mapping */
#define URB_DMA_MAP_PAGE 0x00020000 /* HCD-unsupported S-G */
#define URB_DMA_MAP_SG 0x00040000 /* HCD-supported S-G */
#define URB_MAP_LOCAL 0x00080000 /* HCD-local-memory mapping */
#define URB_SETUP_MAP_SINGLE 0x00100000 /* Setup packet DMA mapped */
#define URB_SETUP_MAP_LOCAL 0x00200000 /* HCD-local setup packet */
#define URB_DMA_SG_COMBINED 0x00400000 /* S-G entries were combined */
#define URB_ALIGNED_TEMP_BUFFER 0x00800000 /* Temp buffer was alloc'd */
struct usb_iso_packet_descriptor {
unsigned int offset;
unsigned int length; /* expected length */
unsigned int actual_length;
int status;
};
struct urb;
struct usb_anchor {
struct list_head urb_list;
wait_queue_head_t wait;
spinlock_t lock;
unsigned int poisoned:1;
};
static inline void init_usb_anchor(struct usb_anchor *anchor)
{
INIT_LIST_HEAD(&anchor->urb_list);
init_waitqueue_head(&anchor->wait);
spin_lock_init(&anchor->lock);
}
typedef void (*usb_complete_t)(struct urb *);
/**
* struct urb - USB Request Block
* @urb_list: For use by current owner of the URB.
* @anchor_list: membership in the list of an anchor
* @anchor: to anchor URBs to a common mooring
* @ep: Points to the endpoint's data structure. Will eventually
* replace @pipe.
* @pipe: Holds endpoint number, direction, type, and more.
* Create these values with the eight macros available;
* usb_{snd,rcv}TYPEpipe(dev,endpoint), where the TYPE is "ctrl"
* (control), "bulk", "int" (interrupt), or "iso" (isochronous).
* For example usb_sndbulkpipe() or usb_rcvintpipe(). Endpoint
* numbers range from zero to fifteen. Note that "in" endpoint two
* is a different endpoint (and pipe) from "out" endpoint two.
* The current configuration controls the existence, type, and
* maximum packet size of any given endpoint.
* @stream_id: the endpoint's stream ID for bulk streams
* @dev: Identifies the USB device to perform the request.
* @status: This is read in non-iso completion functions to get the
* status of the particular request. ISO requests only use it
* to tell whether the URB was unlinked; detailed status for
* each frame is in the fields of the iso_frame-desc.
* @transfer_flags: A variety of flags may be used to affect how URB
* submission, unlinking, or operation are handled. Different
* kinds of URB can use different flags.
* @transfer_buffer: This identifies the buffer to (or from) which the I/O
* request will be performed unless URB_NO_TRANSFER_DMA_MAP is set
* (however, do not leave garbage in transfer_buffer even then).
* This buffer must be suitable for DMA; allocate it with
* kmalloc() or equivalent. For transfers to "in" endpoints, contents
* of this buffer will be modified. This buffer is used for the data
* stage of control transfers.
* @transfer_dma: When transfer_flags includes URB_NO_TRANSFER_DMA_MAP,
* the device driver is saying that it provided this DMA address,
* which the host controller driver should use in preference to the
* transfer_buffer.
* @sg: scatter gather buffer list
* @num_mapped_sgs: (internal) number of mapped sg entries
* @num_sgs: number of entries in the sg list
* @transfer_buffer_length: How big is transfer_buffer. The transfer may
* be broken up into chunks according to the current maximum packet
* size for the endpoint, which is a function of the configuration
* and is encoded in the pipe. When the length is zero, neither
* transfer_buffer nor transfer_dma is used.
* @actual_length: This is read in non-iso completion functions, and
* it tells how many bytes (out of transfer_buffer_length) were
* transferred. It will normally be the same as requested, unless
* either an error was reported or a short read was performed.
* The URB_SHORT_NOT_OK transfer flag may be used to make such
* short reads be reported as errors.
* @setup_packet: Only used for control transfers, this points to eight bytes
* of setup data. Control transfers always start by sending this data
* to the device. Then transfer_buffer is read or written, if needed.
* @setup_dma: DMA pointer for the setup packet. The caller must not use
* this field; setup_packet must point to a valid buffer.
* @start_frame: Returns the initial frame for isochronous transfers.
* @number_of_packets: Lists the number of ISO transfer buffers.
* @interval: Specifies the polling interval for interrupt or isochronous
* transfers. The units are frames (milliseconds) for full and low
* speed devices, and microframes (1/8 millisecond) for highspeed
* and SuperSpeed devices.
* @error_count: Returns the number of ISO transfers that reported errors.
* @context: For use in completion functions. This normally points to
* request-specific driver context.
* @complete: Completion handler. This URB is passed as the parameter to the
* completion function. The completion function may then do what
* it likes with the URB, including resubmitting or freeing it.
* @iso_frame_desc: Used to provide arrays of ISO transfer buffers and to
* collect the transfer status for each buffer.
*
* This structure identifies USB transfer requests. URBs must be allocated by
* calling usb_alloc_urb() and freed with a call to usb_free_urb().
* Initialization may be done using various usb_fill_*_urb() functions. URBs
* are submitted using usb_submit_urb(), and pending requests may be canceled
* using usb_unlink_urb() or usb_kill_urb().
*
* Data Transfer Buffers:
*
* Normally drivers provide I/O buffers allocated with kmalloc() or otherwise
* taken from the general page pool. That is provided by transfer_buffer
* (control requests also use setup_packet), and host controller drivers
* perform a dma mapping (and unmapping) for each buffer transferred. Those
* mapping operations can be expensive on some platforms (perhaps using a dma
* bounce buffer or talking to an IOMMU),
* although they're cheap on commodity x86 and ppc hardware.
*
* Alternatively, drivers may pass the URB_NO_TRANSFER_DMA_MAP transfer flag,
* which tells the host controller driver that no such mapping is needed for
* the transfer_buffer since
* the device driver is DMA-aware. For example, a device driver might
* allocate a DMA buffer with usb_alloc_coherent() or call usb_buffer_map().
* When this transfer flag is provided, host controller drivers will
* attempt to use the dma address found in the transfer_dma
* field rather than determining a dma address themselves.
*
* Note that transfer_buffer must still be set if the controller
* does not support DMA (as indicated by bus.uses_dma) and when talking
* to root hub. If you have to trasfer between highmem zone and the device
* on such controller, create a bounce buffer or bail out with an error.
* If transfer_buffer cannot be set (is in highmem) and the controller is DMA
* capable, assign NULL to it, so that usbmon knows not to use the value.
* The setup_packet must always be set, so it cannot be located in highmem.
*
* Initialization:
*
* All URBs submitted must initialize the dev, pipe, transfer_flags (may be
* zero), and complete fields. All URBs must also initialize
* transfer_buffer and transfer_buffer_length. They may provide the
* URB_SHORT_NOT_OK transfer flag, indicating that short reads are
* to be treated as errors; that flag is invalid for write requests.
*
* Bulk URBs may
* use the URB_ZERO_PACKET transfer flag, indicating that bulk OUT transfers
* should always terminate with a short packet, even if it means adding an
* extra zero length packet.
*
* Control URBs must provide a valid pointer in the setup_packet field.
* Unlike the transfer_buffer, the setup_packet may not be mapped for DMA
* beforehand.
*
* Interrupt URBs must provide an interval, saying how often (in milliseconds
* or, for highspeed devices, 125 microsecond units)
* to poll for transfers. After the URB has been submitted, the interval
* field reflects how the transfer was actually scheduled.
* The polling interval may be more frequent than requested.
* For example, some controllers have a maximum interval of 32 milliseconds,
* while others support intervals of up to 1024 milliseconds.
* Isochronous URBs also have transfer intervals. (Note that for isochronous
* endpoints, as well as high speed interrupt endpoints, the encoding of
* the transfer interval in the endpoint descriptor is logarithmic.
* Device drivers must convert that value to linear units themselves.)
*
* Isochronous URBs normally use the URB_ISO_ASAP transfer flag, telling
* the host controller to schedule the transfer as soon as bandwidth
* utilization allows, and then set start_frame to reflect the actual frame
* selected during submission. Otherwise drivers must specify the start_frame
* and handle the case where the transfer can't begin then. However, drivers
* won't know how bandwidth is currently allocated, and while they can
* find the current frame using usb_get_current_frame_number () they can't
* know the range for that frame number. (Ranges for frame counter values
* are HC-specific, and can go from 256 to 65536 frames from "now".)
*
* Isochronous URBs have a different data transfer model, in part because
* the quality of service is only "best effort". Callers provide specially
* allocated URBs, with number_of_packets worth of iso_frame_desc structures
* at the end. Each such packet is an individual ISO transfer. Isochronous
* URBs are normally queued, submitted by drivers to arrange that
* transfers are at least double buffered, and then explicitly resubmitted
* in completion handlers, so
* that data (such as audio or video) streams at as constant a rate as the
* host controller scheduler can support.
*
* Completion Callbacks:
*
* The completion callback is made in_interrupt(), and one of the first
* things that a completion handler should do is check the status field.
* The status field is provided for all URBs. It is used to report
* unlinked URBs, and status for all non-ISO transfers. It should not
* be examined before the URB is returned to the completion handler.
*
* The context field is normally used to link URBs back to the relevant
* driver or request state.
*
* When the completion callback is invoked for non-isochronous URBs, the
* actual_length field tells how many bytes were transferred. This field
* is updated even when the URB terminated with an error or was unlinked.
*
* ISO transfer status is reported in the status and actual_length fields
* of the iso_frame_desc array, and the number of errors is reported in
* error_count. Completion callbacks for ISO transfers will normally
* (re)submit URBs to ensure a constant transfer rate.
*
* Note that even fields marked "public" should not be touched by the driver
* when the urb is owned by the hcd, that is, since the call to
* usb_submit_urb() till the entry into the completion routine.
*/
struct urb {
/* private: usb core and host controller only fields in the urb */
struct kref kref; /* reference count of the URB */
void *hcpriv; /* private data for host controller */
atomic_t use_count; /* concurrent submissions counter */
atomic_t reject; /* submissions will fail */
int unlinked; /* unlink error code */
/* public: documented fields in the urb that can be used by drivers */
struct list_head urb_list; /* list head for use by the urb's
* current owner */
struct list_head anchor_list; /* the URB may be anchored */
struct usb_anchor *anchor;
struct usb_device *dev; /* (in) pointer to associated device */
struct usb_host_endpoint *ep; /* (internal) pointer to endpoint */
unsigned int pipe; /* (in) pipe information */
unsigned int stream_id; /* (in) stream ID */
int status; /* (return) non-ISO status */
unsigned int transfer_flags; /* (in) URB_SHORT_NOT_OK | ...*/
void *transfer_buffer; /* (in) associated data buffer */
dma_addr_t transfer_dma; /* (in) dma addr for transfer_buffer */
struct scatterlist *sg; /* (in) scatter gather buffer list */
int num_mapped_sgs; /* (internal) mapped sg entries */
int num_sgs; /* (in) number of entries in the sg list */
u32 transfer_buffer_length; /* (in) data buffer length */
u32 actual_length; /* (return) actual transfer length */
unsigned char *setup_packet; /* (in) setup packet (control only) */
dma_addr_t setup_dma; /* (in) dma addr for setup_packet */
int start_frame; /* (modify) start frame (ISO) */
int number_of_packets; /* (in) number of ISO packets */
int interval; /* (modify) transfer interval
* (INT/ISO) */
int error_count; /* (return) number of ISO errors */
void *context; /* (in) context for completion */
usb_complete_t complete; /* (in) completion routine */
struct usb_iso_packet_descriptor iso_frame_desc[0];
/* (in) ISO ONLY */
};
/* ----------------------------------------------------------------------- */
/**
* usb_fill_control_urb - initializes a control urb
* @urb: pointer to the urb to initialize.
* @dev: pointer to the struct usb_device for this urb.
* @pipe: the endpoint pipe
* @setup_packet: pointer to the setup_packet buffer
* @transfer_buffer: pointer to the transfer buffer
* @buffer_length: length of the transfer buffer
* @complete_fn: pointer to the usb_complete_t function
* @context: what to set the urb context to.
*
* Initializes a control urb with the proper information needed to submit
* it to a device.
*/
static inline void usb_fill_control_urb(struct urb *urb,
struct usb_device *dev,
unsigned int pipe,
unsigned char *setup_packet,
void *transfer_buffer,
int buffer_length,
usb_complete_t complete_fn,
void *context)
{
urb->dev = dev;
urb->pipe = pipe;
urb->setup_packet = setup_packet;
urb->transfer_buffer = transfer_buffer;
urb->transfer_buffer_length = buffer_length;
urb->complete = complete_fn;
urb->context = context;
}
/**
* usb_fill_bulk_urb - macro to help initialize a bulk urb
* @urb: pointer to the urb to initialize.
* @dev: pointer to the struct usb_device for this urb.
* @pipe: the endpoint pipe
* @transfer_buffer: pointer to the transfer buffer
* @buffer_length: length of the transfer buffer
* @complete_fn: pointer to the usb_complete_t function
* @context: what to set the urb context to.
*
* Initializes a bulk urb with the proper information needed to submit it
* to a device.
*/
static inline void usb_fill_bulk_urb(struct urb *urb,
struct usb_device *dev,
unsigned int pipe,
void *transfer_buffer,
int buffer_length,
usb_complete_t complete_fn,
void *context)
{
urb->dev = dev;
urb->pipe = pipe;
urb->transfer_buffer = transfer_buffer;
urb->transfer_buffer_length = buffer_length;
urb->complete = complete_fn;
urb->context = context;
}
/**
* usb_fill_int_urb - macro to help initialize a interrupt urb
* @urb: pointer to the urb to initialize.
* @dev: pointer to the struct usb_device for this urb.
* @pipe: the endpoint pipe
* @transfer_buffer: pointer to the transfer buffer
* @buffer_length: length of the transfer buffer
* @complete_fn: pointer to the usb_complete_t function
* @context: what to set the urb context to.
* @interval: what to set the urb interval to, encoded like
* the endpoint descriptor's bInterval value.
*
* Initializes a interrupt urb with the proper information needed to submit
* it to a device.
*
* Note that High Speed and SuperSpeed interrupt endpoints use a logarithmic
* encoding of the endpoint interval, and express polling intervals in
* microframes (eight per millisecond) rather than in frames (one per
* millisecond).
*
* Wireless USB also uses the logarithmic encoding, but specifies it in units of
* 128us instead of 125us. For Wireless USB devices, the interval is passed
* through to the host controller, rather than being translated into microframe
* units.
*/
static inline void usb_fill_int_urb(struct urb *urb,
struct usb_device *dev,
unsigned int pipe,
void *transfer_buffer,
int buffer_length,
usb_complete_t complete_fn,
void *context,
int interval)
{
urb->dev = dev;
urb->pipe = pipe;
urb->transfer_buffer = transfer_buffer;
urb->transfer_buffer_length = buffer_length;
urb->complete = complete_fn;
urb->context = context;
if (dev->speed == USB_SPEED_HIGH || dev->speed == USB_SPEED_SUPER)
urb->interval = 1 << (interval - 1);
else
urb->interval = interval;
urb->start_frame = -1;
}
extern void usb_init_urb(struct urb *urb);
extern struct urb *usb_alloc_urb(int iso_packets, gfp_t mem_flags);
extern void usb_free_urb(struct urb *urb);
#define usb_put_urb usb_free_urb
extern struct urb *usb_get_urb(struct urb *urb);
extern int usb_submit_urb(struct urb *urb, gfp_t mem_flags);
extern int usb_unlink_urb(struct urb *urb);
extern void usb_kill_urb(struct urb *urb);
extern void usb_poison_urb(struct urb *urb);
extern void usb_unpoison_urb(struct urb *urb);
extern void usb_kill_anchored_urbs(struct usb_anchor *anchor);
extern void usb_poison_anchored_urbs(struct usb_anchor *anchor);
extern void usb_unpoison_anchored_urbs(struct usb_anchor *anchor);
extern void usb_unlink_anchored_urbs(struct usb_anchor *anchor);
extern void usb_anchor_urb(struct urb *urb, struct usb_anchor *anchor);
extern void usb_unanchor_urb(struct urb *urb);
extern int usb_wait_anchor_empty_timeout(struct usb_anchor *anchor,
unsigned int timeout);
extern struct urb *usb_get_from_anchor(struct usb_anchor *anchor);
extern void usb_scuttle_anchored_urbs(struct usb_anchor *anchor);
extern int usb_anchor_empty(struct usb_anchor *anchor);
/**
* usb_urb_dir_in - check if an URB describes an IN transfer
* @urb: URB to be checked
*
* Returns 1 if @urb describes an IN transfer (device-to-host),
* otherwise 0.
*/
static inline int usb_urb_dir_in(struct urb *urb)
{
return (urb->transfer_flags & URB_DIR_MASK) == URB_DIR_IN;
}
/**
* usb_urb_dir_out - check if an URB describes an OUT transfer
* @urb: URB to be checked
*
* Returns 1 if @urb describes an OUT transfer (host-to-device),
* otherwise 0.
*/
static inline int usb_urb_dir_out(struct urb *urb)
{
return (urb->transfer_flags & URB_DIR_MASK) == URB_DIR_OUT;
}
void *usb_alloc_coherent(struct usb_device *dev, size_t size,
gfp_t mem_flags, dma_addr_t *dma);
void usb_free_coherent(struct usb_device *dev, size_t size,
void *addr, dma_addr_t dma);
#if 0
struct urb *usb_buffer_map(struct urb *urb);
void usb_buffer_dmasync(struct urb *urb);
void usb_buffer_unmap(struct urb *urb);
#endif
struct scatterlist;
int usb_buffer_map_sg(const struct usb_device *dev, int is_in,
struct scatterlist *sg, int nents);
#if 0
void usb_buffer_dmasync_sg(const struct usb_device *dev, int is_in,
struct scatterlist *sg, int n_hw_ents);
#endif
void usb_buffer_unmap_sg(const struct usb_device *dev, int is_in,
struct scatterlist *sg, int n_hw_ents);
/*-------------------------------------------------------------------*
* SYNCHRONOUS CALL SUPPORT *
*-------------------------------------------------------------------*/
extern int usb_control_msg(struct usb_device *dev, unsigned int pipe,
__u8 request, __u8 requesttype, __u16 value, __u16 index,
void *data, __u16 size, int timeout);
extern int usb_interrupt_msg(struct usb_device *usb_dev, unsigned int pipe,
void *data, int len, int *actual_length, int timeout);
extern int usb_bulk_msg(struct usb_device *usb_dev, unsigned int pipe,
void *data, int len, int *actual_length,
int timeout);
/* wrappers around usb_control_msg() for the most common standard requests */
extern int usb_get_descriptor(struct usb_device *dev, unsigned char desctype,
unsigned char descindex, void *buf, int size);
extern int usb_get_status(struct usb_device *dev,
int type, int target, void *data);
extern int usb_string(struct usb_device *dev, int index,
char *buf, size_t size);
/* wrappers that also update important state inside usbcore */
extern int usb_clear_halt(struct usb_device *dev, int pipe);
extern int usb_reset_configuration(struct usb_device *dev);
extern int usb_set_interface(struct usb_device *dev, int ifnum, int alternate);
extern void usb_reset_endpoint(struct usb_device *dev, unsigned int epaddr);
/* this request isn't really synchronous, but it belongs with the others */
extern int usb_driver_set_configuration(struct usb_device *udev, int config);
/*
* timeouts, in milliseconds, used for sending/receiving control messages
* they typically complete within a few frames (msec) after they're issued
* USB identifies 5 second timeouts, maybe more in a few cases, and a few
* slow devices (like some MGE Ellipse UPSes) actually push that limit.
*/
#define USB_CTRL_GET_TIMEOUT 5000
#define USB_CTRL_SET_TIMEOUT 5000
/**
* struct usb_sg_request - support for scatter/gather I/O
* @status: zero indicates success, else negative errno
* @bytes: counts bytes transferred.
*
* These requests are initialized using usb_sg_init(), and then are used
* as request handles passed to usb_sg_wait() or usb_sg_cancel(). Most
* members of the request object aren't for driver access.
*
* The status and bytecount values are valid only after usb_sg_wait()
* returns. If the status is zero, then the bytecount matches the total
* from the request.
*
* After an error completion, drivers may need to clear a halt condition
* on the endpoint.
*/
struct usb_sg_request {
int status;
size_t bytes;
/* private:
* members below are private to usbcore,
* and are not provided for driver access!
*/
spinlock_t lock;
struct usb_device *dev;
int pipe;
int entries;
struct urb **urbs;
int count;
struct completion complete;
};
int usb_sg_init(
struct usb_sg_request *io,
struct usb_device *dev,
unsigned pipe,
unsigned period,
struct scatterlist *sg,
int nents,
size_t length,
gfp_t mem_flags
);
void usb_sg_cancel(struct usb_sg_request *io);
void usb_sg_wait(struct usb_sg_request *io);
/* ----------------------------------------------------------------------- */
/*
* For various legacy reasons, Linux has a small cookie that's paired with
* a struct usb_device to identify an endpoint queue. Queue characteristics
* are defined by the endpoint's descriptor. This cookie is called a "pipe",
* an unsigned int encoded as:
*
* - direction: bit 7 (0 = Host-to-Device [Out],
* 1 = Device-to-Host [In] ...
* like endpoint bEndpointAddress)
* - device address: bits 8-14 ... bit positions known to uhci-hcd
* - endpoint: bits 15-18 ... bit positions known to uhci-hcd
* - pipe type: bits 30-31 (00 = isochronous, 01 = interrupt,
* 10 = control, 11 = bulk)
*
* Given the device address and endpoint descriptor, pipes are redundant.
*/
/* NOTE: these are not the standard USB_ENDPOINT_XFER_* values!! */
/* (yet ... they're the values used by usbfs) */
#define PIPE_ISOCHRONOUS 0
#define PIPE_INTERRUPT 1
#define PIPE_CONTROL 2
#define PIPE_BULK 3
#define usb_pipein(pipe) ((pipe) & USB_DIR_IN)
#define usb_pipeout(pipe) (!usb_pipein(pipe))
#define usb_pipedevice(pipe) (((pipe) >> 8) & 0x7f)
#define usb_pipeendpoint(pipe) (((pipe) >> 15) & 0xf)
#define usb_pipetype(pipe) (((pipe) >> 30) & 3)
#define usb_pipeisoc(pipe) (usb_pipetype((pipe)) == PIPE_ISOCHRONOUS)
#define usb_pipeint(pipe) (usb_pipetype((pipe)) == PIPE_INTERRUPT)
#define usb_pipecontrol(pipe) (usb_pipetype((pipe)) == PIPE_CONTROL)
#define usb_pipebulk(pipe) (usb_pipetype((pipe)) == PIPE_BULK)
static inline unsigned int __create_pipe(struct usb_device *dev,
unsigned int endpoint)
{
return (dev->devnum << 8) | (endpoint << 15);
}
/* Create various pipes... */
#define usb_sndctrlpipe(dev, endpoint) \
((PIPE_CONTROL << 30) | __create_pipe(dev, endpoint))
#define usb_rcvctrlpipe(dev, endpoint) \
((PIPE_CONTROL << 30) | __create_pipe(dev, endpoint) | USB_DIR_IN)
#define usb_sndisocpipe(dev, endpoint) \
((PIPE_ISOCHRONOUS << 30) | __create_pipe(dev, endpoint))
#define usb_rcvisocpipe(dev, endpoint) \
((PIPE_ISOCHRONOUS << 30) | __create_pipe(dev, endpoint) | USB_DIR_IN)
#define usb_sndbulkpipe(dev, endpoint) \
((PIPE_BULK << 30) | __create_pipe(dev, endpoint))
#define usb_rcvbulkpipe(dev, endpoint) \
((PIPE_BULK << 30) | __create_pipe(dev, endpoint) | USB_DIR_IN)
#define usb_sndintpipe(dev, endpoint) \
((PIPE_INTERRUPT << 30) | __create_pipe(dev, endpoint))
#define usb_rcvintpipe(dev, endpoint) \
((PIPE_INTERRUPT << 30) | __create_pipe(dev, endpoint) | USB_DIR_IN)
static inline struct usb_host_endpoint *
usb_pipe_endpoint(struct usb_device *dev, unsigned int pipe)
{
struct usb_host_endpoint **eps;
eps = usb_pipein(pipe) ? dev->ep_in : dev->ep_out;
return eps[usb_pipeendpoint(pipe)];
}
/*-------------------------------------------------------------------------*/
static inline __u16
usb_maxpacket(struct usb_device *udev, int pipe, int is_out)
{
struct usb_host_endpoint *ep;
unsigned epnum = usb_pipeendpoint(pipe);
if (is_out) {
WARN_ON(usb_pipein(pipe));
ep = udev->ep_out[epnum];
} else {
WARN_ON(usb_pipeout(pipe));
ep = udev->ep_in[epnum];
}
if (!ep)
return 0;
/* NOTE: only 0x07ff bits are for packet size... */
return usb_endpoint_maxp(&ep->desc);
}
/* ----------------------------------------------------------------------- */
/* translate USB error codes to codes user space understands */
static inline int usb_translate_errors(int error_code)
{
switch (error_code) {
case 0:
case -ENOMEM:
case -ENODEV:
return error_code;
default:
return -EIO;
}
}
/* Events from the usb core */
#define USB_DEVICE_ADD 0x0001
#define USB_DEVICE_REMOVE 0x0002
#define USB_BUS_ADD 0x0003
#define USB_BUS_REMOVE 0x0004
extern void usb_register_notify(struct notifier_block *nb);
extern void usb_unregister_notify(struct notifier_block *nb);
#ifdef DEBUG
#define dbg(format, arg...) \
printk(KERN_DEBUG "%s: " format "\n", __FILE__, ##arg)
#else
#define dbg(format, arg...) \
do { \
if (0) \
printk(KERN_DEBUG "%s: " format "\n", __FILE__, ##arg); \
} while (0)
#endif
#define err(format, arg...) \
printk(KERN_ERR KBUILD_MODNAME ": " format "\n", ##arg)
/* debugfs stuff */
extern struct dentry *usb_debug_root;
#endif /* __KERNEL__ */
#endif
