Added missing tegra files.HEADmaster

2 files changed, 66 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
new file mode 100644
index 00000000000..eb4b530d64e
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
@@ -0,0 +1,8 @@
+NVIDIA Tegra 2 GPIO controller
+
+Required properties:
+- compatible : "nvidia,tegra20-gpio"
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional parameters:
+  - bit 0 specifies polarity (0 for normal, 1 for inverted)
+- gpio-controller : Marks the device node as a GPIO controller.
diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt
new file mode 100644
index 00000000000..064db928c3c
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/led.txt
@@ -0,0 +1,58 @@
+LEDs connected to GPIO lines
+
+Required properties:
+- compatible : should be "gpio-leds".
+
+Each LED is represented as a sub-node of the gpio-leds device.  Each
+node's name represents the name of the corresponding LED.
+
+LED sub-node properties:
+- gpios :  Should specify the LED's GPIO, see "Specifying GPIO information
+  for devices" in Documentation/powerpc/booting-without-of.txt.  Active
+  low LEDs should be indicated using flags in the GPIO specifier.
+- label :  (optional) The label for this LED.  If omitted, the label is
+  taken from the node name (excluding the unit address).
+- linux,default-trigger :  (optional) This parameter, if present, is a
+  string defining the trigger assigned to the LED.  Current triggers are:
+    "backlight" - LED will act as a back-light, controlled by the framebuffer
+                  system
+    "default-on" - LED will turn on, but see "default-state" below
+    "heartbeat" - LED "double" flashes at a load average based rate
+    "ide-disk" - LED indicates disk activity
+    "timer" - LED flashes at a fixed, configurable rate
+- default-state:  (optional) The initial state of the LED.  Valid
+  values are "on", "off", and "keep".  If the LED is already on or off
+  and the default-state property is set the to same value, then no
+  glitch should be produced where the LED momentarily turns off (or
+  on).  The "keep" setting will keep the LED at whatever its current
+  state is, without producing a glitch.  The default is off if this
+  property is not present.
+
+Examples:
+
+leds {
+        compatible = "gpio-leds";
+        hdd {
+                label = "IDE Activity";
+                gpios = <&mcu_pio 0 1>; /* Active low */
+                linux,default-trigger = "ide-disk";
+        };
+
+        fault {
+                gpios = <&mcu_pio 1 0>;
+                /* Keep LED on if BIOS detected hardware fault */
+                default-state = "keep";
+        };
+};
+
+run-control {
+        compatible = "gpio-leds";
+        red {
+                gpios = <&mpc8572 6 0>;
+                default-state = "off";
+        };
+        green {
+                gpios = <&mpc8572 7 0>;
+                default-state = "on";
+        };
+}