1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
|
/*
* arch/arm/plat-omap/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for OMAP-based platforms
*
* Copyright (C) 2009 Texas Instruments
* Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <mach/hardware.h>
#include <mach/io.h>
#include <mach/irqs.h>
#include <asm/hardware/gic.h>
#include <plat/omap24xx.h>
#include <plat/omap34xx.h>
#include <plat/omap44xx.h>
#define OMAP2_IRQ_BASE OMAP2_L4_IO_ADDRESS(OMAP24XX_IC_BASE)
#define OMAP3_IRQ_BASE OMAP2_L4_IO_ADDRESS(OMAP34XX_IC_BASE)
#define OMAP4_IRQ_BASE OMAP2_L4_IO_ADDRESS(OMAP44XX_GIC_CPU_BASE)
#define INTCPS_SIR_IRQ_OFFSET 0x0040 /* omap2/3 active interrupt offset */
#define ACTIVEIRQ_MASK 0x7f /* omap2/3 active interrupt bits */
.macro disable_fiq
.endm
.macro arch_ret_to_user, tmp1, tmp2
.endm
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
.pushsection .data
omap_irq_base: .word 0
.popsection
#if defined(CONFIG_ARCH_OMAP2) && defined(CONFIG_ARCH_OMAP3)
/* Configure the interrupt base on the first interrupt */
.macro get_irqnr_preamble, base, tmp
9:
ldr \base, =omap_irq_base @ irq base address
ldr \base, [\base, #0] @ irq base value
cmp \base, #0 @ already configured?
bne 9998f @ nothing to do
mrc p15, 0, \tmp, c0, c0, 0 @ get processor revision
and \tmp, \tmp, #0x000f0000 @ only check architecture
cmp \tmp, #0x00060000 @ is v6?
beq 2400f @ found v6 so it's omap24xx
cmp \tmp, #0x000f0000 @ is cortex?
beq 3400f @ found v7 so it's omap34xx
2400: ldr \base, =OMAP2_IRQ_BASE
ldr \tmp, =omap_irq_base
str \base, [\tmp, #0]
b 9b
3400: ldr \base, =OMAP3_IRQ_BASE
ldr \tmp, =omap_irq_base
str \base, [\tmp, #0]
b 9b
9998:
.endm
#else
.macro get_irqnr_preamble, base, tmp
#ifdef CONFIG_ARCH_OMAP2
ldr \base, =OMAP2_IRQ_BASE
#else
ldr \base, =OMAP3_IRQ_BASE
#endif
.endm
#endif
/* Check the pending interrupts. Note that base already set */
.macro get_irqnr_and_base, irqnr, irqstat, base, tmp
ldr \irqnr, [\base, #0x98] /* IRQ pending reg 1 */
cmp \irqnr, #0x0
bne 9999f
ldr \irqnr, [\base, #0xb8] /* IRQ pending reg 2 */
cmp \irqnr, #0x0
bne 9999f
ldr \irqnr, [\base, #0xd8] /* IRQ pending reg 3 */
cmp \irqnr, #0x0
9999:
ldrne \irqnr, [\base, #INTCPS_SIR_IRQ_OFFSET]
and \irqnr, \irqnr, #ACTIVEIRQ_MASK /* Clear spurious bits */
.endm
#endif
#ifdef CONFIG_ARCH_OMAP4
.macro get_irqnr_preamble, base, tmp
.endm
/*
* The interrupt numbering scheme is defined in the
* interrupt controller spec. To wit:
*
* Interrupts 0-15 are IPI
* 16-28 are reserved
* 29-31 are local. We allow 30 to be used for the watchdog.
* 32-1020 are global
* 1021-1022 are reserved
* 1023 is "spurious" (no interrupt)
*
* For now, we ignore all local interrupts so only return an
* interrupt if it's between 30 and 1020. The test_for_ipi
* routine below will pick up on IPIs.
* A simple read from the controller will tell us the number
* of the highest priority enabled interrupt.
* We then just need to check whether it is in the
* valid range for an IRQ (30-1020 inclusive).
*/
.macro get_irqnr_and_base, irqnr, irqstat, base, tmp
ldr \base, =OMAP4_IRQ_BASE
ldr \irqstat, [\base, #GIC_CPU_INTACK]
ldr \tmp, =1021
bic \irqnr, \irqstat, #0x1c00
cmp \irqnr, #29
cmpcc \irqnr, \irqnr
cmpne \irqnr, \tmp
cmpcs \irqnr, \irqnr
.endm
/* We assume that irqstat (the raw value of the IRQ acknowledge
* register) is preserved from the macro above.
* If there is an IPI, we immediately signal end of interrupt
* on the controller, since this requires the original irqstat
* value which we won't easily be able to recreate later.
*/
.macro test_for_ipi, irqnr, irqstat, base, tmp
bic \irqnr, \irqstat, #0x1c00
cmp \irqnr, #16
it cc
strcc \irqstat, [\base, #GIC_CPU_EOI]
it cs
cmpcs \irqnr, \irqnr
.endm
/* As above, this assumes that irqstat and base are preserved */
.macro test_for_ltirq, irqnr, irqstat, base, tmp
bic \irqnr, \irqstat, #0x1c00
mov \tmp, #0
cmp \irqnr, #29
itt eq
moveq \tmp, #1
streq \irqstat, [\base, #GIC_CPU_EOI]
cmp \tmp, #0
.endm
#endif
.macro irq_prio_table
.endm
|
