/**
 * drivers/gpio/max7301.c
 *
 * Copyright (C) 2006 Juergen Beisert, Pengutronix
 * Copyright (C) 2008 Guennadi Liakhovetski, Pengutronix
 * Copyright (C) 2009 Wolfram Sang, Pengutronix
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 * The Maxim MAX7300/1 device is an I2C/SPI driven GPIO expander. There are
 * 28 GPIOs. 8 of them can trigger an interrupt. See datasheet for more
 * details
 * Note:
 * - DIN must be stable at the rising edge of clock.
 * - when writing:
 *   - always clock in 16 clocks at once
 *   - at DIN: D15 first, D0 last
 *   - D0..D7 = databyte, D8..D14 = commandbyte
 *   - D15 = low -> write command
 * - when reading
 *   - always clock in 16 clocks at once
 *   - at DIN: D15 first, D0 last
 *   - D0..D7 = dummy, D8..D14 = register address
 *   - D15 = high -> read command
 *   - raise CS and assert it again
 *   - always clock in 16 clocks at once
 *   - at DOUT: D15 first, D0 last
 *   - D0..D7 contains the data from the first cycle
 *
 * The driver exports a standard gpiochip interface
 */

#include <linux/module.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mutex.h>
#include <linux/spi/max7301.h>
#include <linux/gpio.h>
#include <linux/slab.h>

/*
 * Pin configurations, see MAX7301 datasheet page 6
 */
#define PIN_CONFIG_MASK 0x03
#define PIN_CONFIG_IN_PULLUP 0x03
#define PIN_CONFIG_IN_WO_PULLUP 0x02
#define PIN_CONFIG_OUT 0x01

#define PIN_NUMBER 28

static int max7301_direction_input(struct gpio_chip *chip, unsigned offset)
{
	struct max7301 *ts = container_of(chip, struct max7301, chip);
	u8 *config;
	u8 offset_bits;
	int ret;

	/* First 4 pins are unused in the controller */
	offset += 4;
	offset_bits = (offset & 3) << 1;

	config = &ts->port_config[offset >> 2];

	mutex_lock(&ts->lock);

	/* Standard GPIO API doesn't support pull-ups, has to be extended.
	 * Hard-coding no pollup for now. */
	*config = (*config & ~(PIN_CONFIG_MASK << offset_bits))
			   | (PIN_CONFIG_IN_WO_PULLUP << offset_bits);

	ret = ts->write(ts->dev, 0x08 + (offset >> 2), *config);

	mutex_unlock(&ts->lock);

	return ret;
}

static int __max7301_set(struct max7301 *ts, unsigned offset, int value)
{
	if (value) {
		ts->out_level |= 1 << offset;
		return ts->write(ts->dev, 0x20 + offset, 0x01);
	} else {
		ts->out_level &= ~(1 << offset);
		return ts->write(ts->dev, 0x20 + offset, 0x00);
	}
}

static int max7301_direction_output(struct gpio_chip *chip, unsigned offset,
				    int value)
{
	struct max7301 *ts = container_of(chip, struct max7301, chip);
	u8 *config;
	u8 offset_bits;
	int ret;

	/* First 4 pins are unused in the controller */
	offset += 4;
	offset_bits = (offset & 3) << 1;

	config = &ts->port_config[offset >> 2];

	mutex_lock(&ts->lock);

	*config = (*config & ~(PIN_CONFIG_MASK << offset_bits))
			   | (PIN_CONFIG_OUT << offset_bits);