aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/media
Commit message (Collapse)AuthorAge
* V4L/DVB (12410): em28xx: Move the non-board dependent part to be outside ↵Mauro Carvalho Chehab2009-08-13
| | | | | | | | | | | | | em28xx_pre_card_setup() em28xx_pre_card_setup() is meant to contain board-specific initialization. Also, as autodetection sometimes occur only after having i2c bus enabled, this function may need to be called later. Moving those setups to happen outside the function avoids calling it twice without need and without duplicating output lines at dmesg. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12407): em28xx: Adjust Silvercrest xtal frequencyMauro Carvalho Chehab2009-08-13
| | | | | | | | | | We don't know the xtal frequency of Silvercrest, but we need to have some value in order to allow controlling the frame rate frequency. The value is probably still wrong, since the manufacturer announces this device as being capable of 30fps, but the maximum we can get is 13.5 fps. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12406): em28xx: fix: don't do image interlacing on webcamsMauro Carvalho Chehab2009-08-13
| | | | | | | | | | | | | | Due to historical reasons, em28xx driver gets two consecutive frames and fold them into an unique framing, doing interlacing. While this works fine for TV images, this produces two bad effects with webcams: 1) webcam images are progressive. Merging two consecutive images produce interlacing artifacts on the image; 2) since the driver needs to get two frames, it reduces the maximum frame rate by two. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12403): em28xx: properly reports some em2710 chipsMauro Carvalho Chehab2009-08-13
| | | | | | | | | | | As reported by hermann pitton <hermann-pitton@arcor.de>, some devices has a different chip id for em2710 (likely the older ones): em28xx: New device @ 480 Mbps (eb1a:2710, interface 0, class 0) em28xx #0: Identified as EM2710/EM2750/EM2751 webcam grabber (card=22) em28xx #0: em28xx chip ID = 17 Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12402): em28xx: fix: some em2710 chips use a different vendor IDMauro Carvalho Chehab2009-08-13
| | | | | | | | Thanks to hermann pitton <hermann-pitton@arcor.de> for pointing this new variation. Tested-by: hermann pitton <hermann-pitton@arcor.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12401): m9v011: add vflip/hflip controls to control mirror/upside downMauro Carvalho Chehab2009-08-13
| | | | Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12400): em28xx: Allow changing fps on webcamsMauro Carvalho Chehab2009-08-13
| | | | | | | | em28xx doesn't have temporal scaling. However, on webcams, sensors are capable of changing the output rate. So, VIDIOC_[G|S]_PARM ioctls should be passed to the sensor for it to properly set frame rate. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12399): mt9v011: Add support for controlling frame ratesMauro Carvalho Chehab2009-08-13
| | | | | | | | Implement g_parm/s_parm ioctls. Those are used to check the current frame rate (in fps) and to set it to a value. In practice, there are only 15 possible different speeds, due to chip limits. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12394): cx88: Disable xc3028 power management for Geniatech x8000Devin Heitmueller2009-08-13
| | | | | | | | | | | | | | | A user discovered that the Geniatech x8000 encountered a regression when the xc3028 power management was introduced. The xc3028 never recovers after setting the powerdown register, which is probably because the xc3028 reset GPIO is not properly configured. Since I do not have access to the hardware and thus cannot determine the correct GPIO configuration, just disable xc3028 power management on this board, which fixes the regression. Thanks to user "ritec" for reporting the issue and testing the fix. Cc: rictec <rictec@netcabo.pt> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12393): cx88: fix regression in tuning for Geniatech X8000 MTDevin Heitmueller2009-08-13
| | | | | | | | The introduction of the zl10353 i2c gate control broke support for the Geniatech board (which is not behind an i2 gate). Add the needed parameter. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12391): saa7134: Use correct product name for Hauppauge ↵Michael Krufky2009-08-13
| | | | | | | WinTV-HVR1120 DVB-T/Hybrid Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12390): saa7134: Use correct product name for Hauppauge ↵Michael Krufky2009-08-13
| | | | | | | WinTV-HVR1150 ATSC/QAM-Hybrid Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12386): sms1xxx: fix build warning: unused variable 'board'Michael Krufky2009-08-13
| | | | | | | | | | | | | | | | Remove the following build warning: sms-cards.c: In function 'sms_board_event': sms-cards.c:120: warning: unused variable 'board' Thanks to Hans Verkuil for pointing this out. The problem code has been #if 0'd for now, this will likely be used again in the future, once the event interface is complete. Cc: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12380): uvcvideo: Avoid flooding the kernel log with "unknown event ↵Laurent Pinchart2009-08-13
| | | | | | | | | | | | type" messages The iSight sends non-UVC status events through the interrupt endpoint. Those invalid events are reported to the kernel log, resulting in a log flood. Only log the events when the UVC_TRACE_STATUS flag is set. Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12328): uvcvideo: Don't apply the FIX_BANDWIDTH quirk to all ↵Laurent Pinchart2009-08-13
| | | | | | | | | | | ViMicro devices Commit 50144aeeb702ea105697ae5249f059ea3990b838 broke the Samsung NC10 netbook webcam. Instead of applying the FIX_BANDWIDTH quirk to all ViMicro devices, list the devices explicitly. Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12374): sms1xxx: fix broken Hauppauge devicesMichael Krufky2009-08-13
| | | | | | | | | | The current GPIO configuration breaks all Hauppauge devices. The code being removed affects Hauppauge devices only, and is the cause of the breakage. Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12371): af9015: Fix for crash in dvb-usb-af9015Nils Kassube2009-08-13
| | | | | | | | | Moving BOOT fixes problem. Signed-off-by: Nils Kassube <kassube@gmx.net> Acked-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12362): cx23885-417: fix manipulation of tvnormsMichael Krufky2009-08-13
| | | | | | | | | | | | | | | | Currently, the VIDIOC_S_STD ioctl just returns -EINVAL regardless of the norm passed. This patch sets cx23885_mpeg_template.tvnorms and cx23885_mpeg_template.current_norm so that the VIDIOC_S_STD will work. Thanks to Joseph Yasi for pointing this out, even though this particular fix was already pushed into a development repository, merge priority of this changeset has been escalated as a result of Joseph posting this identical patch. Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Joseph A. Yasi <joe.yasi@gmail.com> Reviewed-by: Steven Toth <stoth@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12349): cx88: HVR1300 ensure switching from Encoder to DVB-T and ↵Sohail Syyed2009-08-13
| | | | | | | | | | back is reliable Current tip is broken and does not switch back to DVB-T correctly Signed-off-by: Sohail Syyed <linuxtv@hubstar.net> Signed-off-by: Steven Toth <stoth@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12344): em28xx: fix support for Plextor ConvertX PX-TV100UMauro Carvalho Chehab2009-08-13
| | | | | | | | | | | This device uses msp34xx and uses 2.048 MHz frequency for I2S communication. Thanks to Angelo Cano <acano@fastmail.fm> for pointing the issues with this device and proposing an approach for fixing the issue. Tested-by: Angelo Cano <acano@fastmail.fm> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12341): zl10353 and qt1010: fix stack corruption bugJan Nikitenko2009-08-13
| | | | | | | | | | | | | | | Fixes stack corruption bug present in dump_regs function of zl10353 and qt1010 drivers: the buffer buf was one byte smaller than required - there are 4 chars for address prefix, 16 * 3 chars for dump of 16 eeprom bytes per line and 1 byte for zero ending the string required, i.e. 53 bytes, but only 52 were provided. The one byte missing in stack based buffer buf can cause stack corruption possibly leading to kernel oops, as discovered originally with af9015 driver (af9015: fix stack corruption bug). Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12340): mtv9v011: Add a missing chip version to the driverMauro Carvalho Chehab2009-08-13
| | | | | | | | | | | Some mt9v011 webcams report 0x8332 chip version, instead of 0x8243. From the revision history at the mt9v011 datasheet, it seems that the chip version has changed from the first release of the chip. Thanks-to hermann pitton <hermann-pitton@arcor.de> for pointing this to me, on his tests with a Silvercrest webcam. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12338): cx18: Read buffer overflowAndy Walls2009-08-13
| | | | | | | | | This mistakenly tested against sizeof(freqs) instead of the array size. Due to the mask the only illegal value possible was 3. Reported-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12337): ivtv: Read buffer overflowRoel Kluin2009-08-13
| | | | | | | | | This mistakenly tests against sizeof(freqs) instead of the array size. Due to the mask the only illegal value possible was 3. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12330): pxa_camera: Fix Oops in pxa_camera_probeAntonio Ospite2009-08-13
| | | | | | | | mclk_get_divisor uses pcdev->soc_host.dev, make sure it is initialized. Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12303): cx23885: check pointers before dereferencing in dprintk macroMichael Krufky2009-07-24
| | | | | | | | | When enabling debug with v4l_debug set to 2 or greater, the driver OOPS's on startup. Checks dev pointer before dereferencing, in order to prevent this OOPS. Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12302): cx23885-417: fix broken IOCTL handlingMichael Krufky2009-07-24
| | | | | | | | IOCTLS will never get handled if we dont connect video_ioctl2 to mpeg_fops.ioctl Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12300): bttv: fix regression: tvaudio must be loaded before tunerHans Verkuil2009-07-24
| | | | | | | | | | | | Both tvaudio and the tuner share i2c address 0x42. The tvaudio module can check whether it really is a tda9840, but the tuner can't. So the tvaudio module must be loaded before the tuner module. This was also the case for 2.6.29, but the order was swapped in 2.6.30. Thanks to Krzysztof Grygiencz for reporting and testing this. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12291): b2c2: fix frontends compiled into kernelTrent Piepho2009-07-24
| | | | | | | | | | | | | | A recent patch didn't take into account that frontends can be compiled into the kernel. Or that frontends compiled as modules can't be used by the b2c2 driver if it is not a module itself. Some frontends require multiple drivers, e.g. a demod driver and a tuner driver. The code for the frontend support was getting added if the demod driver was available. Change this to also require any needed tuner or SEC drivers as well. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12286): sn9c20x: reorder includes to be like other driversMauro Carvalho Chehab2009-07-24
| | | | | | | This is not just pure cosmetic, since the order affects the out-of-tree module build at the -hg development tree. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12284): gspca - jpeg subdrivers: Check the result of kmalloc(jpeg ↵Julia Lawall2009-07-24
| | | | | | | | header). Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12283): gspca - sn9c20x: New subdriver for sn9c201 and sn9c202 bridges.Brian Johnson2009-07-24
| | | | | | Signed-off-by: Brian Johnson <brijohn@gmail.com> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12282): gspca - main: Support for vidioc_g_chip_ident and ↵Brian Johnson2009-07-24
| | | | | | | | vidioc_g/s_register. Signed-off-by: Brian Johnson <brijohn@gmail.com> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12269): af9013: auto-detect parameters in case of garbage given by appAntti Palosaari2009-07-24
| | | | | | | | | | | | | | | | Request demodulator auto-detect transmission parameters in case of garbage parameters provided by application for compatibility. That's needed at least for MPlayer compatibility currently. Thanks to Jelle de Jong for reporting issue and providing SSH access to Devin for debugging. Thanks to Devin Heitmueller for hard debug work he did to find that bug. Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Cc: Jelle de Jong <jelledejong@powercraft.nl> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12267): gspca - sonixj: Bad sensor init of non ov76xx sensors.Jean-Francois Moine2009-07-24
| | | | | | | The bug was introduced when adding the light frequency control Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12265): em28xx: fix tuning problem in HVR-900 (R1)Devin Heitmueller2009-07-24
| | | | | | | | | | | | | | | | | | | When the change was introduced in the zl10353 for the i2c gate behavior, this broke the HVR-900 which was not behind a gate. Use a version of the zl10353 config profile that indicates the tuner is not behind such a gate. Without this patch the first tune succeeds, but subsequent tuning attempts will fail. The change also renames the terratec zl10353 profile I wrote to be more generic, since it is shared by the non-terratec device. Thanks to Michael Krufky for providing a HVR-900 and DVB-T environment to test with. Cc: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12263): em28xx: set demod profile for Pinnacle Hybrid Pro 320eDevin Heitmueller2009-07-24
| | | | | | | | | | | | The Pinnacle Hybrid Pro 320e was missing a demod config for the xc3028, which is required for digital tuning to work properly. Add the missing profile. Thanks to Andreas Lunderhage for testing patches and providing a remote debug environment. Cc: Andreas Lunderhage <lunderhage@home.se> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12262): em28xx: Make sure the tuner is initialized if generic empia ↵Devin Heitmueller2009-07-24
| | | | | | | | | | | | | | | | | | | USB id was used In cases where the device has a generic Empia USB ID, the call in the precard setup phase did not set the tuner GPIO. As a result, the tuner may not be taken out of reset before attempting initialization in the analog driver. This problem was not seen before with the EVGA inDtube, since that particular board has the analog GPIO setup to include taking the tuner out of reset. Thanks to Andreas Lunderhage for testing patches and providing a remote debug environment for the Pinnacle 320e. Cc: Andreas Lunderhage <lunderhage@home.se> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12261): em28xx: set GPIO properly for Pinnacle Hybrid Pro analog ↵Devin Heitmueller2009-07-24
| | | | | | | | | | support Set the GPIO properly for the analog side of the Pinnacle Hybrid Pro, or else the emp202 doesn't get detected properly. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12260): em28xx: make support work for the Pinnacle Hybrid Pro ↵Devin Heitmueller2009-07-24
| | | | | | | | | | | | | | (eb1a:2881) Setup the GPIOs properly and enable support for the DVB side of the Pinnacle Hybrid Pro USB stick. Thanks to Andreas Lunderhage for testing patches and providing a remote debug environment. Cc: Andreas Lunderhage <lunderhage@home.se> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12258): em28xx: fix typo in mt352 init sequence for Terratec ↵Devin Heitmueller2009-07-24
| | | | | | | | | | | | | | Cinergy T XS USB Andy walls pointed out that we were passing 0x5d to the TUNER_GO register, instead of 0x01. Set the register properly (note the code did still work with the incorrect value, so this does not address a regression). Thanks to Andy Walls for noticing the issue. Cc: Andy Walls <awalls@radix.net> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12257): em28xx: make tuning work for Terratec Cinergy T XS USB ↵Devin Heitmueller2009-07-24
| | | | | | | | | | | | | (mt352 variant) The Terratec Cinergy T XS USB can have either a zl10353 or an mt352. Add support for the MT352 variant. Thanks to Jelle de Jong for providing a unit to test/debug with. Cc: Jelle de Jong <jelledejong@powercraft.nl> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12245): em28xx: add support for mt9m001 webcamsMauro Carvalho Chehab2009-07-24
| | | | | | | Thanks to Wally <wally@voosen.eu> for bringing the issue and helping with the tests. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12244): em28xx: adjust vinmode/vinctl based on the stream input formatMauro Carvalho Chehab2009-07-24
| | | | | | | | | Depending on the video input format, vinmode/vinctl needs adjustments. For TV, this is not relevant, since the supported decoders output data at the same format. However, webcam sensors may have different formats, so, this needs to be adjusted based on the device. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12243): em28xx: allow specifying sensor xtal frequencyMauro Carvalho Chehab2009-07-24
| | | | | | | | | | | | | | In order to properly estimate fps, mt9v011 sensor driver needs to know what is the used frequency on the sensor cristal. Adds the proper fields and initialization code for specifying the cristal frequency. Also, based on experimentation, it was noticed that the Silvercrest is outputing data at 7 fps. This means that it should be using a 6.3 MHz cristal. This information needs to be double checked later, by opening the device. Anyway, by using this value for xtal, at least now we have the correct fps report. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12242): mt9v011: implement core->s_config to allow adjusting xtal ↵Mauro Carvalho Chehab2009-07-24
| | | | | | | | | | frequency Since frames per second is a function of cristal frequency, and this is device-specific, add a function that allows adjusting it, via subdev->core->s_config callback. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12241): mt9v011: Fix vstartMauro Carvalho Chehab2009-07-24
| | | | | | vstart calculus were wrong. Fix it. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12240): mt9v011: add a function to calculate frames per second rateMauro Carvalho Chehab2009-07-24
| | | | | | | | | | | It is possible to adjust the fps rate by changing some register values. This is function of the connected Xtal at the camera sensor, being a 27 MHz cristal needed, in order to support 640x480 at 30 fps. For now, it will only calculate the values for fps. Later patches may introduce V4L2 ioctls, to allow frequency rate adjustments. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12239): em28xx: fix webcam scalingMauro Carvalho Chehab2009-07-24
| | | | | | | | | | | | | | | While trying to fix an mt9v001 webcam, I noticed that HSCALE/VSCALE do work with em28xx + webcam. The issue is that the scaling setup depends on the number of visible rows/cols of the input image. With mt9v011 (Silvercrest), the resolution is 640x480. So, the scaling is different from a normal TV image (720x480 on NTSC). This were causing a wrong scaling and a previous patch disabled scaling. As each sensor have their different resolution setting, the xres/yres should be adjusted accordingly with the input sensor. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* V4L/DVB (12238): em28xx: call sensor detection code for all webcam entriesMauro Carvalho Chehab2009-07-24
| | | | | | | | | | | | With the previous approach, autodetection were working only for the two generic entries (em275x and em2820 unknown ones). So, if someone would try to force probing an specific device, the code would not properly run the autodetection code. With the new approach, the sensor autodetection will be run not only for the two generic entries, but also do webcam specific ones. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
generated by cgit v1.2.2 (git 2.25.0) at 2024-10-08 08:30:03 -0400