| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
| |
Some commands don't work in its example doc. The patch will fix it.
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When the mdio-gpio driver is probed via device trees, the platform
device id is set as -1, However the pdev->id is re-used as bus-id for
while creating mdio gpio bus.
So
For device tree case the mdio-gpio bus name appears as "gpio-ffffffff"
where as
for non-device tree case the bus name appears as "gpio-<bus-num>"
Which means the bus_id is fixed in device tree case, so we can't have
two mdio gpio buses via device trees. Assigning a logical bus number
via device tree solves the problem and the bus name is much consistent
with non-device tree bus name.
Without this patch
1. we can't support two mdio-gpio buses via device trees.
2. we should always pass gpio-ffffffff as bus name to phy_connect, very
different to non-device tree bus name.
So, setting up the bus_id via aliases from device tree is the right
solution and other drivers do similar thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (12 patches)
revert "mm: fix-up zone present pages"
tmpfs: change final i_blocks BUG to WARNING
tmpfs: fix shmem_getpage_gfp() VM_BUG_ON
mm: highmem: don't treat PKMAP_ADDR(LAST_PKMAP) as a highmem address
mm: revert "mm: vmscan: scale number of pages reclaimed by reclaim/compaction based on failures"
rapidio: fix kernel-doc warnings
swapfile: fix name leak in swapoff
memcg: fix hotplugged memory zone oops
mips, arc: fix build failure
memcg: oom: fix totalpages calculation for memory.swappiness==0
mm: fix build warning for uninitialized value
mm: add anon_vma_lock to validate_mm()
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
oom_badness() takes a totalpages argument which says how many pages are
available and it uses it as a base for the score calculation. The value
is calculated by mem_cgroup_get_limit which considers both limit and
total_swap_pages (resp. memsw portion of it).
This is usually correct but since fe35004fbf9e ("mm: avoid swapping out
with swappiness==0") we do not swap when swappiness is 0 which means
that we cannot really use up all the totalpages pages. This in turn
confuses oom score calculation if the memcg limit is much smaller than
the available swap because the used memory (capped by the limit) is
negligible comparing to totalpages so the resulting score is too small
if adj!=0 (typically task with CAP_SYS_ADMIN or non zero oom_score_adj).
A wrong process might be selected as result.
The problem can be worked around by checking mem_cgroup_swappiness==0
and not considering swap at all in such a case.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull networking updates from David Miller:
1) tx_filtered/ps_tx_buf queues need to be accessed with the SKB queue
lock, from Arik Nemtsov.
2) Don't call 802.11 driver's filter configure method until it's
actually open, from Felix Fietkau.
3) Use ieee80211_free_txskb otherwise we leak control information.
From Johannes Berg.
4) Fix memory leak in bluetooth UUID removal,f rom Johan Hedberg.
5) The shift mask trick doesn't work properly when 'optname' is out of
range in do_ip_setsockopt(). Use a straightforward switch statement
instead, the compiler emits essentially the same code but without
the missing range check. From Xi Wang.
6) Fix when we call tcp_replace_ts_recent() otherwise we can
erroneously accept a too-high tsval. From Eric Dumazet.
7) VXLAN bug fixes, mostly to do with VLAN header length handling, from
Alexander Duyck.
8) Missing return value initialization for IPV6_MINHOPCOUNT socket
option handling. From Hannes Frederic.
9) Fix regression in tasklet handling in jme/ksz884x/xilinx drivers,
from Xiaotian Feng.
10) At smsc911x driver init time, we don't know if the chip is in word
swap mode or not. However we do need to wait for the control
register's ready bit to be set before we program any other part of
the chip. Adjust the wait loop to account for this. From Kamlakant
Patel.
11) Revert erroneous MDIO bus unregister change to mdio-bitbang.c
12) Fix memory leak in /proc/net/sctp/, from Tommi Rantala.
13) tilegx driver registers IRQ with NULL name, oops, from Simon Marchi.
14) TCP metrics hash table kzalloc() based allocation can fail, back
down to using vmalloc() if it does. From Eric Dumazet.
15) Fix packet steering out-of-order delivery regression, from Tom
Herbert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
net-rps: Fix brokeness causing OOO packets
tcp: handle tcp_net_metrics_init() order-5 memory allocation failures
batman-adv: process broadcast packets in BLA earlier
batman-adv: don't add TEMP clients belonging to other backbone nodes
batman-adv: correctly pass the client flag on tt_response
batman-adv: fix tt_global_entries flags update
tilegx: request_irq with a non-null device name
net: correct check in dev_addr_del()
tcp: fix retransmission in repair mode
sctp: fix /proc/net/sctp/ memory leak
Revert "drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free"
net/smsc911x: Fix ready check in cases where WORD_SWAP is needed
drivers/net: fix tasklet misuse issue
ipv4/ip_vti.c: VTI fix post-decryption forwarding
brcmfmac: fix typo in CONFIG_BRCMISCAN
vxlan: Update hard_header_len based on lowerdev when instantiating VXLAN
vxlan: fix a typo.
ipv6: setsockopt(IPIPPROTO_IPV6, IPV6_MINHOPCOUNT) forgot to set return value
doc/net: Fix typo in netdev-features.txt
vxlan: Fix error that was resulting in VXLAN MTU size being 10 bytes too large
...
|
| | |/
| |
| |
| |
| | |
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This is mostly a revert of 01dc52ebdf47 ("oom: remove deprecated oom_adj")
from Davidlohr Bueso.
It reintroduces /proc/pid/oom_adj for backwards compatibility with earlier
kernels. It simply scales the value linearly when /proc/pid/oom_score_adj
is written.
The major difference is that its scheduled removal is no longer included
in Documentation/feature-removal-schedule.txt. We do warn users with a
single printk, though, to suggest the more powerful and supported
/proc/pid/oom_score_adj interface.
Reported-by: Artem S. Tashkinov <t.artem@lycos.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\
| |
| |
| | |
Linux 3.7-rc4
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
"Just a few driver fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: tsc40 - remove wrong announcement of pressure support
Input: lpc32xx-keys - select INPUT_MATRIXKMAP
Input: pxa27x_keypad - clear pending interrupts on keypad config
Input: wacom - correct bad Cintiq 24HD check
Input: wacom - add INPUT_PROP_DIRECT flag to Cintiq 24HD
Input: egalax_ts - get gpio from devicetree
|
| | | |\ |
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The irq_to_gpio() is old, most platforms use GENERIC_GPIO framework
and don't support this API anymore.
The i.MX6q sabrelite platform equips an egalax touchscreen controller,
and this platform already transfered to GENERIC_GPIO framework, to
support this driver, we use a more generic way to get gpio.
Add a return value checking for waking up the controller in the probe
function, this guarantee only a workable device can pass init.
[dmitry.torokhov@gmail.com: Make driver depend on CONFIG_OF as it is
now required.]
Acked-by Zhang Jiejing <jiejing.zhang@freescale.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| | | |/
| |/|
| | |
| | |
| | | |
Signed-off-by: Andreas Herrmann <herrmann.der.user@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we had a
few of these patches cause regressions themselves and had to work out
how to deal with those in the meantime."
* tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
Revert "ARM i.MX25: Fix PWM per clock lookups"
ARM: versatile: fix versatile_defconfig
ARM: mvebu: update defconfig with 3.7 changes
ARM: at91: fix at91x40 build
ARM: socfpga: Fix socfpga compilation with early_printk() enabled
ARM: SPEAr: Remove unused empty files
MAINTAINERS: Add arm-soc tree entry
ARM: dts: mxs: add the "clock-names" for gpmi-nand
ARM: ux500: Correct SDI5 address and add some format changes
ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT
ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE
ARM: at91: drop duplicated config SOC_AT91SAM9 entry
ARM: at91/i2c: change id to let i2c-at91 work
ARM: at91/i2c: change id to let i2c-gpio work
ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
ARM: at91: fix external interrupt specification in board code
ARM: at91: fix external interrupts in non-DT case
ARM: at91: at91sam9g10: fix SOC type detection
ARM: at91/tc: fix typo in the DT document
ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
...
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org> [v3.4]
|
| | |\ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are a number of firmware core fixes for 3.7, and some other minor
fixes. And some documentation updates thrown in for good measure.
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Documentation:Chinese translation of Documentation/arm64/memory.txt
Documentation:Chinese translation of Documentation/arm64/booting.txt
Documentation:Chinese translation of Documentation/IRQ.txt
firmware loader: document kernel direct loading
sysfs: sysfs_pathname/sysfs_add_one: Use strlcat() instead of strcat()
dynamic_debug: Remove unnecessary __used
firmware loader: sync firmware cache by async_synchronize_full_domain
firmware loader: let direct loading back on 'firmware_buf'
firmware loader: fix one reqeust_firmware race
firmware loader: cancel uncache work before caching firmware
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This is a Chinese translated version of
Documentation/arm64/memory.txt
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This is a Chinese translated version of
Documentation/arm64/booting.txt
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This is a Chinese translated version of
Documentation/IRQ.txt
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Harry Wei <harryxiyou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |/ /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch adds description on recently introduced direct firmware
loading by Linus.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |\ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"This fixes a few pinctrl problems seen since v3.7-rc1:
- Section tagging for init code
- Use proper pointers to lookup struct device * in the bcm2835
(a.k.a. Raspberry Pi)
- Remove duplicate #includes
- Fix bad return values in errorpath
- Remove extraneous pull function from the sirf driver causing build
errors
- Provide compilation stubs for the Nomadik pinctrl driver when used
with legacy systems without PRCMU units
- Various irqdomain fixes in the Nomadik driver as predicted
- Various smallish bugs in the Tegra driver, most also targeted for
stable
- Removed a deadlocking mutex in the groups debugfs show function"
* tag 'pinctrl-v3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/nomadik: pass DT node to the irqdomain
pinctrl/nomadik: use zero as default irq_start
pinctrl: fix missing unlock on error in pinctrl_groups_show()
pinctrl/nomadik: use irq_create_mapping()
pinctrl: remove mutex lock in groups show
pinctrl: tegra: correct bank for pingroup and drv pingroup
pinctrl: tegra: set low power mode bank width to 2
dt: Document: correct tegra20/30 pinctrl slew-rate name
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
change nvidia,slew_rate* to nvidia,slew-rate*
Cc: stable@kernel.org
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |\ \ \ \
| | |_|/ /
| |/| | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core kernel fixes from Ingo Molnar:
"Two small fixes"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Documentation: Reflect the new location of the NMI watchdog info
nohz: Fix idle ticks in cpu summary line of /proc/stat
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Commit 9919cba7 ("watchdog: Update documentation") moved the
NMI watchdog documentation from nmi_watchdog.txt to
lockup-watchdogs.txt. Update the index file accordingly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Don Zickus <dzickus@redhat.com>
Link: http://lkml.kernel.org/r/20121021120551.4656d99b@endymion.delvare
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| |/ / / /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This is to reuse the same pmd table that is sparsely populated with
the modules space.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Drop some leftover dependencies on CONFIG_EXPERIMENTAL, and add
support for Intel Atom CE4110/4150/4170."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (coretemp) Add support for Atom CE4110/4150/4170
Documentation/hwmon: remove CONFIG_EXPERIMENTAL
hwmon: (pmbus) remove CONFIG_EXPERIMENTAL
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
TjMax for the CE4100 series of Atom CPUs was previously reported to be
110 degrees C.
cpuinfo logs on the web show existing CPU types CE4110, CE4150, and CE4170,
reported as "model name : Intel(R) Atom(TM) CPU CE41{1|5|7}0 @ 1.{2|6}0GHz"
with model 28 (0x1c) and stepping 10 (0x0a). Add the three known variants
to the tjmax table.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
cc: stable@vger.kernel.org
Acked-by: Jean Delvare <khali@linux-fr.org>
|
| | | |/ /
| |/| |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Jean Delvare <khali@linux-fr.org>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Rob Landley <rob@landley.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Media fixes for:
- one Kconfig fix patch;
- one patch fixing DocBook breakage due to the drivers/media UAPI
changes;
- the remaining UAPI media changes (DVB API).
I'm aware that is is a little late for the UAPI renames for the DVB
API, but IMHO, it is better to merge it for 3.7, due to two reasons:
1) There is a major rename at 3.7 (not only uapi changes, but also
the entire media drivers were reorganized on 3.7, in order to
simplify the Kconfig logic, and easy drivers selection, especially
for hybrid devices). By confining all those renames there at 3.7
it will cause all the harm at for media developers on just one
shot. Stable backports upstream and at distros will likely
welcome it as well, as they won't need to check what changed on
3.7 and what was postponed for on 3.8.
2) The V4L2 DocBook Makefile creates a cross-reference between the
media API headers and the specs. This helps us _a_lot_ to be sure
that all API improvements are properly documented. Every time a
header changes from one place to another, DocBook/media/Makefile
needs to be patched. Currently, the DocBook breakage patch
depends on the DVB UAPI."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] Kconfig: Fix dependencies for driver autoselect options
DocBook/media/Makefile: Fix build due to uapi breakage
UAPI: (Scripted) Disintegrate include/linux/dvb
|
| | |/ / /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The uapi changeset forgot to fix the header locations, needed
for the DocBook specs. Fix it.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Pull sparc fixes from David Miller:
"Two sparc64 perf bug fixes and add a sysrq facility so I can diagnose
these kinds of problems more quickly in the future."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix bit twiddling in sparc_pmu_enable_event().
sparc64: Add global PMU register dumping via sysrq.
sparc64: Like x86 we should check current->mm during perf backtrace generation.
|
| | |/ / /
| | | |
| | | |
| | | | |
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Merge emailed patches from Corey Minyard:
"Remove some bogus docs, Fix ACPI/IPMI interactions, fix some warnings,
and add register spacing detection for PCI interfaces."
* ipmi:
IPMI: Detect register spacing on PCI interfaces
IPMI: Fix some uninitialized warning
IPMI: Change link order
ACPI: Reorder IPMI driver before any other ACPI drivers
IPMI: Remove SMBus driver info from the docs
|
| | |/ / /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Some documentation for the SMBus driver is in the IPMI docs, but that
code is not in the kernel tree at this point. So remove the docs to
avoid confusion.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |/ / /
| | |
| | |
| | |
| | |
| | |
| | | |
Update file paths in Documentation/DocBook/networking.tmpl for uapi headers.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
We do a very simple search for a particular string appended to the module
(which is cache-hot and about to be SHA'd anyway). There's both a config
option and a boot parameter which control whether we accept or fail with
unsigned modules and modules that are signed with an unknown key.
If module signing is enabled, the kernel will be tainted if a module is
loaded that is unsigned or has a signature for which we don't have the
key.
(Useful feedback and tweaks by David Howells <dhowells@redhat.com>)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
In-source documentation for the asymmetric key type. This will be located in:
Documentation/crypto/asymmetric-keys.txt
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Give the key type the opportunity to preparse the payload prior to the
instantiation and update routines being called. This is done with the
provision of two new key type operations:
int (*preparse)(struct key_preparsed_payload *prep);
void (*free_preparse)(struct key_preparsed_payload *prep);
If the first operation is present, then it is called before key creation (in
the add/update case) or before the key semaphore is taken (in the update and
instantiate cases). The second operation is called to clean up if the first
was called.
preparse() is given the opportunity to fill in the following structure:
struct key_preparsed_payload {
char *description;
void *type_data[2];
void *payload;
const void *data;
size_t datalen;
size_t quotalen;
};
Before the preparser is called, the first three fields will have been cleared,
the payload pointer and size will be stored in data and datalen and the default
quota size from the key_type struct will be stored into quotalen.
The preparser may parse the payload in any way it likes and may store data in
the type_data[] and payload fields for use by the instantiate() and update()
ops.
The preparser may also propose a description for the key by attaching it as a
string to the description field. This can be used by passing a NULL or ""
description to the add_key() system call or the key_create_or_update()
function. This cannot work with request_key() as that required the description
to tell the upcall about the key to be created.
This, for example permits keys that store PGP public keys to generate their own
name from the user ID and public key fingerprint in the key.
The instantiate() and update() operations are then modified to look like this:
int (*instantiate)(struct key *key, struct key_preparsed_payload *prep);
int (*update)(struct key *key, struct key_preparsed_payload *prep);
and the new payload data is passed in *prep, whether or not it was preparsed.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Pull md updates from NeilBrown:
- "discard" support, some dm-raid improvements and other assorted bits
and pieces.
* tag 'md-3.7' of git://neil.brown.name/md: (29 commits)
md: refine reporting of resync/reshape delays.
md/raid5: be careful not to resize_stripes too big.
md: make sure manual changes to recovery checkpoint are saved.
md/raid10: use correct limit variable
md: writing to sync_action should clear the read-auto state.
Subject: [PATCH] md:change resync_mismatches to atomic64_t to avoid races
md/raid5: make sure to_read and to_write never go negative.
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
md/raid5: protect debug message against NULL derefernce.
md/raid5: add some missing locking in handle_failed_stripe.
MD: raid5 avoid unnecessary zero page for trim
MD: raid5 trim support
md/bitmap:Don't use IS_ERR to judge alloc_page().
md/raid1: Don't release reference to device while handling read error.
raid: replace list_for_each_continue_rcu with new interface
add further __init annotations to crypto/xor.c
DM RAID: Fix for "sync" directive ineffectiveness
DM RAID: Fix comparison of index and quantity for "rebuild" parameter
DM RAID: Add rebuild capability for RAID10
DM RAID: Move 'rebuild' checking code to its own function
...
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
DM RAID: Add code to validate replacement slots for RAID10 arrays
RAID10 can handle 'copies - 1' failures for each mirror group. This code
ensures the user has provided a valid array - one whose devices specified for
rebuild do not exceed the amount of redundancy available.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
| |\ \ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull ACPI & Thermal updates from Len Brown:
"The generic Linux thermal layer is gaining some new capabilities
(generic cooling via cpufreq) and some new customers (ARM).
Also, an ACPI EC bug fix plus a regression fix."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (30 commits)
tools/power/acpi/acpidump: remove duplicated include from acpidump.c
ACPI idle, CPU hotplug: Fix NULL pointer dereference during hotplug
cpuidle / ACPI: fix potential NULL pointer dereference
ACPI: EC: Add a quirk for CLEVO M720T/M730T laptop
ACPI: EC: Make the GPE storm threshold a module parameter
thermal: Exynos: Fix NULL pointer dereference in exynos_unregister_thermal()
Thermal: Fix bug on cpu_cooling, cooling device's id conflict problem.
thermal: exynos: Use devm_* functions
ARM: exynos: add thermal sensor driver platform data support
thermal: exynos: register the tmu sensor with the kernel thermal layer
thermal: exynos5: add exynos5250 thermal sensor driver support
hwmon: exynos4: move thermal sensor driver to driver/thermal directory
thermal: add generic cpufreq cooling implementation
Fix a build error.
thermal: Fix potential NULL pointer accesses
thermal: add Renesas R-Car thermal sensor support
thermal: fix potential out-of-bounds memory access
Thermal: Introduce locking for cdev.thermal_instances list.
Thermal: Unify the code for both active and passive cooling
Thermal: Introduce simple arbitrator for setting device cooling state
...
|
| | | \ \ \ \ | |
| | | \ \ \ \ | |
| | |\ \ \ \ \ \ |
|
| | | | |\ \ \ \ \
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux into thermal
Conflicts:
drivers/staging/omap-thermal/omap-thermal-common.
OMAP supplied dummy TC1 and TC2,
at the same time that the thermal tree removed them
from thermal_zone_device_register()
drivers/thermal/cpu_cooling.c b/drivers/thermal/cpu_cooling.c
propogate the upstream MAX_IDR_LEVEL re-name
to prevent a build failure
Previously-fixed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Len Brown <len.brown@intel.com>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
This movement is needed because the hwmon entries and corresponding sysfs
interface is a duplicate of utilities already provided by
driver/thermal/thermal_sys.c. The goal is to place it in thermal folder
and add necessary functions to use the in-kernel thermal interfaces.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: SangWook Ju <sw.ju@samsung.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
This patchset introduces a new generic cooling device based on cpufreq
that can be used on non-ACPI platforms. As a proof of concept, we have
drivers for the following platforms using this mechanism now:
* Samsung Exynos (Exynos4 and Exynos5) in the current patchset.
* Freescale i.MX (git://git.linaro.org/people/amitdanielk/linux.git imx6q_thermal)
There is a small change in cpufreq cooling registration APIs, so a minor
change is needed for Freescale platforms.
Brief Description:
1) The generic cooling devices code is placed inside driver/thermal/*
as placing inside acpi folder will need un-necessary enabling of acpi
code. This code is architecture independent.
2) This patchset adds generic cpu cooling low level implementation
through frequency clipping. In future, other cpu related cooling
devices may be added here. An ACPI version of this already exists
(drivers/acpi/processor_thermal.c) .But this will be useful for
platforms like ARM using the generic thermal interface along with the
generic cpu cooling devices. The cooling device registration API's
return cooling device pointers which can be easily binded with the
thermal zone trip points. The important APIs exposed are,
a) struct thermal_cooling_device *cpufreq_cooling_register(
struct cpumask *clip_cpus)
b) void cpufreq_cooling_unregister(struct thermal_cooling_device *cdev)
3) Samsung exynos platform thermal implementation is done using the
generic cpu cooling APIs and the new trip type. The temperature sensor
driver present in the hwmon folder(registered as hwmon driver) is moved
to thermal folder and registered as a thermal driver.
A simple data/control flow diagrams is shown below,
Core Linux thermal <-----> Exynos thermal interface <----- Temperature Sensor
| |
\|/ |
Cpufreq cooling device <---------------
TODO:
*Will send the DT enablement patches later after the driver is merged.
This patch:
Add support for generic cpu thermal cooling low level implementations
using frequency scaling up/down based on the registration parameters.
Different cpu related cooling devices can be registered by the user and
the binding of these cooling devices to the corresponding trip points can
be easily done as the registration APIs return the cooling device pointer.
The user of these APIs are responsible for passing clipping frequency .
The drivers can also register to recieve notification about any cooling
action called.
[akpm@linux-foundation.org: fix comment layout]
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: SangWook Ju <sw.ju@samsung.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
set upper and lower limits when binding
a thermal cooling device to a thermal zone device.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
| |\ \ \ \ \ \ \ \ \
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | | |
Pull misc SCSI updates from James Bottomley:
"This is an assorted set of stragglers into the merge window with
driver updates for megaraid_sas, lpfc, bfi and mvumi. It also
includes some fairly major fixes for virtio-scsi (scatterlist init),
scsi_debug (off by one error), storvsc (use after free) and qla2xxx
(potential deadlock).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (49 commits)
[SCSI] storvsc: Account for in-transit packets in the RESET path
[SCSI] qla2xxx: fix potential deadlock on ha->hardware_lock
[SCSI] scsi_debug: Fix off-by-one bug when unmapping region
[SCSI] Shorten the path length of scsi_cmd_to_driver()
[SCSI] virtio-scsi: support online resizing of disks
[SCSI] virtio-scsi: fix LUNs greater than 255
[SCSI] virtio-scsi: initialize scatterlist structure
[SCSI] megaraid_sas: Version, Changelog, Copyright update
[SCSI] megaraid_sas: Remove duplicate code
[SCSI] megaraid_sas: Add SystemPD FastPath support
[SCSI] megaraid_sas: Add array boundary check for SystemPD
[SCSI] megaraid_sas: Load io_request DataLength in bytes
[SCSI] megaraid_sas: Add module param for configurable MSI-X vector count
[SCSI] megaraid_sas: Remove un-needed completion_lock spinlock calls
[SCSI] lpfc 8.3.35: Update lpfc version for 8.3.35 driver release
[SCSI] lpfc 8.3.35: Fixed not reporting logical link speed to SCSI midlayer when QoS not on
[SCSI] lpfc 8.3.35: Fix error with fabric service parameters causing performance issues
[SCSI] lpfc 8.3.35: Fixed SCSI host create showing wrong link speed on SLI3 HBA ports
[SCSI] lpfc 8.3.35: Fixed not checking solicition in progress bit when verifying FCF record for use
[SCSI] lpfc 8.3.35: Fixed messages for misconfigured port errors
...
|
| | | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | | |
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
| | | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | | |
documentation
The Link Error Status Block attributes are incorrectly named as they do
not have the lesb_ prefix, but instead are grouped in the lesb/ attribute
group.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
| |\ \ \ \ \ \ \ \ \ \
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | | |
Pull nfsd update from J Bruce Fields:
"Another relatively quiet cycle. There was some progress on my
remaining 4.1 todo's, but a couple of them were just of the form
"check that we do X correctly", so didn't have much affect on the
code.
Other than that, a bunch of cleanup and some bugfixes (including an
annoying NFSv4.0 state leak and a busy-loop in the server that could
cause it to peg the CPU without making progress)."
* 'for-3.7' of git://linux-nfs.org/~bfields/linux: (46 commits)
UAPI: (Scripted) Disintegrate include/linux/sunrpc
UAPI: (Scripted) Disintegrate include/linux/nfsd
nfsd4: don't allow reclaims of expired clients
nfsd4: remove redundant callback probe
nfsd4: expire old client earlier
nfsd4: separate session allocation and initialization
nfsd4: clean up session allocation
nfsd4: minor free_session cleanup
nfsd4: new_conn_from_crses should only allocate
nfsd4: separate connection allocation and initialization
nfsd4: reject bad forechannel attrs earlier
nfsd4: enforce per-client sessions/no-sessions distinction
nfsd4: set cl_minorversion at create time
nfsd4: don't pin clientids to pseudoflavors
nfsd4: fix bind_conn_to_session xdr comment
nfsd4: cast readlink() bug argument
NFSD: pass null terminated buf to kstrtouint()
nfsd: remove duplicate init in nfsd4_cb_recall
nfsd4: eliminate redundant nfs4_free_stateid
fs/nfsd/nfs4idmap.c: adjust inconsistent IS_ERR and PTR_ERR
...
|
