aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* wl1251: remove fixed address support from spi commandsKalle Valo2009-08-14
| | | | | | | | The fixed addresses are not used in wl1251, only in wl1271. So it can be safely removed. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Update beacon RSSISujith2009-08-14
| | | | | | | | ANI uses the beacon RSSI for its operation. Update this properly. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Remove local chainmask variableSujith2009-08-14
| | | | | | | | The chainmask can be obtained directly from ath_hw. Also, use a helper macro for comparing CTLs - this improves readability. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Cleanup TX power calculation for 4K chipsSujith2009-08-14
| | | | | | | | Write CCK power-per-rate array always and report correct TX power to regulatory. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Clean antenna configuration for 4K EEPROM chipsSujith2009-08-14
| | | | | | | | This patch revamps the antenna configuration mechanism for 4K chips. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Add macros for Antenna DiversitySujith2009-08-14
| | | | | | | | A subsequent patch would use these for configuring antennae on AR9285. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Cleanup ath9k_hw_4k_set_gain() interfaceSujith2009-08-14
| | | | | | | regChainOffset is always zero, remove it. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Split eeprom.c into manageable piecesSujith2009-08-14
| | | | | | | | Add eeprom_def.c, eeprom_4k.c and eeprom_9287.c This improves maintainability. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Remove a few DEBUG mesagesSujith2009-08-14
| | | | | | | We have never used these at all. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Try to fix whitespace damageSujith2009-08-14
| | | | | Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Cleanup function return typesSujith2009-08-14
| | | | | Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Remove unneeded assignment of protocol fieldSujith2009-08-14
| | | | | Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: Set WEP ciphersSamuel Ortiz2009-08-14
| | | | | | | | | | With iwconfig there is no way to properly set the ciphers when trying to connect to a WEP SSID. Although mac80211 based drivers dont need it, several fullmac drivers do. This patch basically sets the WEP ciphers whenever they're not set at all. Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: fix SME association after disassociationJohannes Berg2009-08-14
| | | | | | | | | | | | | When an AP disassociates us, we currently go into a weird state because the SME doesn't handle authenticated but not associated well unless it's within its own state machine, it can't recover from that. However, it shouldn't need to, since we don't do any decisions in it really -- so when we get disconnected, simply deauthenticate too. Reported-by: Pavel Roskin <proski@gnu.org> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: fix nl80211 disconnected eventsJohannes Berg2009-08-14
| | | | | | | | | | | | When reporting a disconnection to userspace, we try to report whether it was from the AP or by our own choice. However, we misreported a broadcast deauth or disassoc as being by own choice, which is wrong. Fix this by checking the sender address instead of the destination address. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: stay authenticated after disassocJohannes Berg2009-08-14
| | | | | | | | | | | | | | | After being disassociated by the AP, mac80211 currently reports this to cfg80211, and then goes to delete the association. That's fine, but cfg80211 assumes that it's still authenticated, however, mac80211 throws away all state. This fixes mac80211 to keep track of the authentication in that case so that cfg80211 can request a deauth or new association properly. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1271: add wl1271 to Kconfig and the MakefileLuciano Coelho2009-08-14
| | | | | | | | This patch adds support for the wl1271 driver in the Kconfig and in the Makefile. Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1271: add wl1271 driver filesLuciano Coelho2009-08-14
| | | | | | | | | | | | | | This driver supports the wl1271 chipset from Texas Instruments based on the WiLink(tm) 6.0 mobile platform. Support for wl1273 should be relatively easy to add. This chipset is designed for embedded devices, with good powersaving capabilities. The wl1271 chipset is the successor of wl1251 and supports the 802.11b/g/n standards, but currently this driver supports only b/g. More information about this chipset can be found here: http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12762&contentId=29993 Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: fix disassociation warning due to misuse of wdev->current_bssPavel Roskin2009-08-14
| | | | | | | | | | | WARN_ON was triggered at mlme.c:213 when dissociating from an AP. wdev->current_bss->pub.bssid should be used in place of wdev->current_bss for BSSID comparison. Signed-off-by: Pavel Roskin <proski@gnu.org> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* orinoco: consolidate storage of WEP and TKIP keysDavid Kilroy2009-08-14
| | | | | | | | | | | When TKIP support was added, we stored the keys separately to avoid issues when both TKIP and WEP keys are sent to the driver. We need to consolidate the storage to convert to cfg80211, so do this first and try iron out the issues. Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* orinoco: add function to retrieve current bssidDavid Kilroy2009-08-14
| | | | | | | We will need this from the cfg80211 disassociate call. Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* orinoco: move disassociation to hw.cDavid Kilroy2009-08-14
| | | | | | | This allows the disassociation to be called via cfg80211. Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* orinoco: pass orinoco_set_tkip_key the sequence lengthsDavid Kilroy2009-08-14
| | | | | | | | When we store the keys for cfg80211, the sequence lengths will also be stored. So avoid assuming the sequence lengths at this level. Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* orinoco: use local types for auth alg and sequence lengthDavid Kilroy2009-08-14
| | | | | | | | This helps in the refactorring required to convert the driver to cfg80211. Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* orinoco: prefer_port3 can be a single bitDavid Kilroy2009-08-14
| | | | | | | | This is a boolean value set based on firmware capabilities, so move the variable to the capabilities section and reduce the structure size. Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wireless: display wext SSID when connected by cfg80211Zhu Yi2009-08-14
| | | | | | | | | | cfg80211 displays correct link info when connected by wext. But if the connection is setup by cfg80211, wext cannot display the SSID. This patch fixed this issue. Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Fix fallout from the IEEE80211_IF_TYPE to NL80211_IFTYPE change.Gábor Stefanik2009-08-14
| | | | | | | Update a comment that still says IEEE80211_IF_TYPE instead of NL80211_IFTYPE. Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: remove wrong probe_resp_plcp writegregor kowski2009-08-14
| | | | | | | | | | | The tkip hw support uncovered a bug in b43_write_probe_resp_template : it is writing at the wrong shm offset, it is in the B43_SHM_SH_TKIPTSCTTAK zone. Remove b43_write_probe_resp_template, b43_write_probe_resp_plcp and b43_write_probe_resp_plcp because the probe response offload is currently not supported by mac80211. Signed-off-by: Gregor Kowski <gregor.kowski@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Typo fixes & minor cleanupGábor Stefanik2009-08-14
| | | | | | | | Make use of HostFlags defines in the LP-PHY code. Fix fallout from the IEEE80211_IF_TYPE to NL80211_IFTYPE change. Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: fix compilation of mesh (although its disabled)Luis R. Rodriguez2009-08-14
| | | | | | | | | | | | | | | Mesh is currently disabled on mac80211, its marked as broken. This patch gets it to compile though, to account for the mac80211 workqueue changes. There was a simple typo in the patches for mesh for the workqueue migration, but we never compile tested it as we couldn't even select mesh as its broken. Lets at least let it compile for those interested in getting it fixed. Reported-by: Pat Erley <pat-lkml@erley.org> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Add LP 2063 radio initGábor Stefanik2009-08-14
| | | | | | | | Add B2063 radio init code and tables for LP-PHY. Rename structures common between B2062 and B2063 to B206X. Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* zd1211rw: make it clear we don't use leds.h LED stuffLuis R. Rodriguez2009-08-14
| | | | | | | | zd1211rw uses its own LED stuff so let rename its LED stuff as such. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: use new FIF_PSPOLL configure filterLuis R. Rodriguez2009-08-14
| | | | | | | | | | | | We used to set pspoll filter on ath9k on AP mode but we no longer need this mode specific check as mac80211 now does the check for us and informs us when we should enable pspoll through FIF_PSPOLL. Cc: Igor Perminov <igor.perminov@inbox.ru> Cc: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath5k: fix missing output in monitor mode after ifconfig upJoerg Albert2009-08-14
| | | | | | | | | | | | | | | | | Let ath5k_chan_set() always call ath5k_reset(). This fixes the bug that we don't get any packets in monitor mode after: ifconfig wlan0 down iwconfig wlan0 mode monitor channel 1 ifconfig wlan0 up but they arrive after iwconfig wlan0 channel 2 Signed-off-by: Joerg Albert <jal2@gmx.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* bnx2x: update version to 1.52.1Eilon Greenstein2009-08-13
| | | | | Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Whitespaces and commentsEilon Greenstein2009-08-13
| | | | | Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Removing unused definitionsEilon Greenstein2009-08-13
| | | | | | Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Beautify bnx2x_dump.hEilon Greenstein2009-08-13
| | | | | | Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Re-factor the initialization codeEilon Greenstein2009-08-13
| | | | | | | | | Moving the code to a more logical place and beautifying it. No real change in behavior. Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Using PCI_DEVICE macroEilon Greenstein2009-08-13
| | | | | Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Adding explicit castingEilon Greenstein2009-08-13
| | | | | Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Using macro for phy addressEilon Greenstein2009-08-13
| | | | | Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Re-arrange the link structures for better alignmentEilon Greenstein2009-08-13
| | | | | | | | | Change ieee_fc to u16 instead of u32 and re-arrange the link parameters structures Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Missing smp_wmb for statistics state machineEilon Greenstein2009-08-13
| | | | | | Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Remove SGMII configuration when not requiredEilon Greenstein2009-08-13
| | | | | | Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Keep only one HW path activeEilon Greenstein2009-08-13
| | | | | | | | | Disable bmac access while working with emac and keep the single lane SerDes in reset while working with 4 lanes XGXS Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Check unzip return codeEilon Greenstein2009-08-13
| | | | | | | | | | Without this check, when running out of memory, we will see PSOD's in bnx2x_init_fill() when doing a memset(). This is because at that time, bp->gunzip_buf is not pointing to a valid allocated space. Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Remove the init_dmae field from bpEilon Greenstein2009-08-13
| | | | | | | | | | | | | Moved the dmae_command from the heap to the stack. This will save 56 bytes per bnx2x structure. As a side benefit, we can also reduce the time the dmae_mutex is held. This is because do we not need to hold this mutex when setting up the dmae command. The memory where is dmae command is stored is not a shared resource and doesn not need to be protected. Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Updating regdump_len at drvinfoEilon Greenstein2009-08-13
| | | | | Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Move printing of version from probe to the initEilon Greenstein2009-08-13
| | | | | | | | | | | Move printing of version from probe to the init function Rather then checking if this is the first module probe call to print the version of the driver only once, the statement is moved to the init function of the module where init is only called once Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.2 (git 2.25.0) at 2024-11-20 05:15:48 -0500