1 files changed, 365 insertions, 6 deletions

diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h
index bbfa1093f606..c7ccaae15af6 100644
--- a/include/linux/nl80211.h
+++ b/include/linux/nl80211.h
@@ -77,6 +77,39 @@
  */
 
 /**
+ * DOC: Virtual interface / concurrency capabilities
+ *
+ * Some devices are able to operate with virtual MACs, they can have
+ * more than one virtual interface. The capability handling for this
+ * is a bit complex though, as there may be a number of restrictions
+ * on the types of concurrency that are supported.
+ *
+ * To start with, each device supports the interface types listed in
+ * the %NL80211_ATTR_SUPPORTED_IFTYPES attribute, but by listing the
+ * types there no concurrency is implied.
+ *
+ * Once concurrency is desired, more attributes must be observed:
+ * To start with, since some interface types are purely managed in
+ * software, like the AP-VLAN type in mac80211 for example, there's
+ * an additional list of these, they can be added at any time and
+ * are only restricted by some semantic restrictions (e.g. AP-VLAN
+ * cannot be added without a corresponding AP interface). This list
+ * is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute.
+ *
+ * Further, the list of supported combinations is exported. This is
+ * in the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute. Basically,
+ * it exports a list of "groups", and at any point in time the
+ * interfaces that are currently active must fall into any one of
+ * the advertised groups. Within each group, there are restrictions
+ * on the number of interfaces of different types that are supported
+ * and also the number of different channels, along with potentially
+ * some other restrictions. See &enum nl80211_if_combination_attrs.
+ *
+ * All together, these attributes define the concurrency of virtual
+ * interfaces that a given device supports.
+ */
+
+/**
  * enum nl80211_commands - supported nl80211 commands
  *
  * @NL80211_CMD_UNSPEC: unspecified command to catch errors
@@ -203,6 +236,28 @@
  * @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons,
  *      partial scan results may be available
  *
+ * @NL80211_CMD_START_SCHED_SCAN: start a scheduled scan at certain
+ *      intervals, as specified by %NL80211_ATTR_SCHED_SCAN_INTERVAL.
+ *      Like with normal scans, if SSIDs (%NL80211_ATTR_SCAN_SSIDS)
+ *      are passed, they are used in the probe requests.  For
+ *      broadcast, a broadcast SSID must be passed (ie. an empty
+ *      string).  If no SSID is passed, no probe requests are sent and
+ *      a passive scan is performed.  %NL80211_ATTR_SCAN_FREQUENCIES,
+ *      if passed, define which channels should be scanned; if not
+ *      passed, all channels allowed for the current regulatory domain
+ *      are used.  Extra IEs can also be passed from the userspace by
+ *      using the %NL80211_ATTR_IE attribute.
+ * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan
+ * @NL80211_CMD_SCHED_SCAN_RESULTS: indicates that there are scheduled scan
+ *      results available.
+ * @NL80211_CMD_SCHED_SCAN_STOPPED: indicates that the scheduled scan has
+ *      stopped.  The driver may issue this event at any time during a
+ *      scheduled scan.  One reason for stopping the scan is if the hardware
+ *      does not support starting an association or a normal scan while running
+ *      a scheduled scan.  This event is also sent when the
+ *      %NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface
+ *      is brought down while a scheduled scan was running.
+ *
  * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation
  *      or noise level
  * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to
@@ -410,6 +465,24 @@
  *      notification. This event is used to indicate that an unprotected
  *      disassociation frame was dropped when MFP is in use.
  *
+ * @NL80211_CMD_NEW_PEER_CANDIDATE: Notification on the reception of a
+ *      beacon or probe response from a compatible mesh peer.  This is only
+ *      sent while no station information (sta_info) exists for the new peer
+ *      candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH is set.  On
+ *      reception of this notification, userspace may decide to create a new
+ *      station (@NL80211_CMD_NEW_STATION).  To stop this notification from
+ *      reoccurring, the userspace authentication daemon may want to create the
+ *      new station with the AUTHENTICATED flag unset and maybe change it later
+ *      depending on the authentication result.
+ *
+ * @NL80211_CMD_GET_WOWLAN: get Wake-on-Wireless-LAN (WoWLAN) settings.
+ * @NL80211_CMD_SET_WOWLAN: set Wake-on-Wireless-LAN (WoWLAN) settings.
+ *      Since wireless is more complex than wired ethernet, it supports
+ *      various triggers. These triggers can be configured through this
+ *      command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For
+ *      more background information, see
+ *      http://wireless.kernel.org/en/users/Documentation/WoWLAN.
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */
@@ -522,6 +595,16 @@ enum nl80211_commands {
         NL80211_CMD_UNPROT_DEAUTHENTICATE,
         NL80211_CMD_UNPROT_DISASSOCIATE,
 
+        NL80211_CMD_NEW_PEER_CANDIDATE,
+
+        NL80211_CMD_GET_WOWLAN,
+        NL80211_CMD_SET_WOWLAN,
+
+        NL80211_CMD_START_SCHED_SCAN,
+        NL80211_CMD_STOP_SCHED_SCAN,
+        NL80211_CMD_SCHED_SCAN_RESULTS,
+        NL80211_CMD_SCHED_SCAN_STOPPED,
+
         /* add new commands above here */
 
         /* used to define NL80211_CMD_MAX below */
@@ -545,6 +628,7 @@ enum nl80211_commands {
 /* source-level API compatibility */
 #define NL80211_CMD_GET_MESH_PARAMS NL80211_CMD_GET_MESH_CONFIG
 #define NL80211_CMD_SET_MESH_PARAMS NL80211_CMD_SET_MESH_CONFIG
+#define NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE NL80211_MESH_SETUP_IE
 
 /**
  * enum nl80211_attrs - nl80211 netlink attributes
@@ -886,6 +970,31 @@ enum nl80211_commands {
  *      changed once the mesh is active.
  * @NL80211_ATTR_MESH_CONFIG: Mesh configuration parameters, a nested attribute
  *      containing attributes from &enum nl80211_meshconf_params.
+ * @NL80211_ATTR_SUPPORT_MESH_AUTH: Currently, this means the underlying driver
+ *      allows auth frames in a mesh to be passed to userspace for processing via
+ *      the @NL80211_MESH_SETUP_USERSPACE_AUTH flag.
+ * @NL80211_ATTR_STA_PLINK_STATE: The state of a mesh peer link as
+ *      defined in &enum nl80211_plink_state. Used when userspace is
+ *      driving the peer link management state machine.
+ *      @NL80211_MESH_SETUP_USERSPACE_AMPE must be enabled.
+ *
+ * @NL80211_ATTR_WOWLAN_SUPPORTED: indicates, as part of the wiphy capabilities,
+ *      the supported WoWLAN triggers
+ * @NL80211_ATTR_WOWLAN_TRIGGERS: used by %NL80211_CMD_SET_WOWLAN to
+ *      indicate which WoW triggers should be enabled. This is also
+ *      used by %NL80211_CMD_GET_WOWLAN to get the currently enabled WoWLAN
+ *      triggers.
+
+ * @NL80211_ATTR_SCHED_SCAN_INTERVAL: Interval between scheduled scan
+ *      cycles, in msecs.
+ *
+ * @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported
+ *      interface combinations. In each nested item, it contains attributes
+ *      defined in &enum nl80211_if_combination_attrs.
+ * @NL80211_ATTR_SOFTWARE_IFTYPES: Nested attribute (just like
+ *      %NL80211_ATTR_SUPPORTED_IFTYPES) containing the interface types that
+ *      are managed in software: interfaces of these types aren't subject to
+ *      any restrictions in their number or combinations.
  *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
@@ -1074,6 +1183,17 @@ enum nl80211_attrs {
         NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX,
         NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX,
 
+        NL80211_ATTR_SUPPORT_MESH_AUTH,
+        NL80211_ATTR_STA_PLINK_STATE,
+
+        NL80211_ATTR_WOWLAN_TRIGGERS,
+        NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED,
+
+        NL80211_ATTR_SCHED_SCAN_INTERVAL,
+
+        NL80211_ATTR_INTERFACE_COMBINATIONS,
+        NL80211_ATTR_SOFTWARE_IFTYPES,
+
         /* add attributes here, update the policy in nl80211.c */
 
         __NL80211_ATTR_AFTER_LAST,
@@ -1126,7 +1246,9 @@ enum nl80211_attrs {
  * @NL80211_IFTYPE_ADHOC: independent BSS member
  * @NL80211_IFTYPE_STATION: managed BSS member
  * @NL80211_IFTYPE_AP: access point
- * @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points
+ * @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points; VLAN interfaces
+ *      are a bit special in that they must always be tied to a pre-existing
+ *      AP type interface.
  * @NL80211_IFTYPE_WDS: wireless distribution interface
  * @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames
  * @NL80211_IFTYPE_MESH_POINT: mesh point
@@ -1168,6 +1290,7 @@ enum nl80211_iftype {
  *      with short barker preamble
  * @NL80211_STA_FLAG_WME: station is WME/QoS capable
  * @NL80211_STA_FLAG_MFP: station uses management frame protection
+ * @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated
  * @NL80211_STA_FLAG_MAX: highest station flag number currently defined
  * @__NL80211_STA_FLAG_AFTER_LAST: internal use
  */
@@ -1177,6 +1300,7 @@ enum nl80211_sta_flags {
         NL80211_STA_FLAG_SHORT_PREAMBLE,
         NL80211_STA_FLAG_WME,
         NL80211_STA_FLAG_MFP,
+        NL80211_STA_FLAG_AUTHENTICATED,
 
         /* keep last */
         __NL80211_STA_FLAG_AFTER_LAST,
@@ -1222,6 +1346,36 @@ enum nl80211_rate_info {
 };
 
 /**
+ * enum nl80211_sta_bss_param - BSS information collected by STA
+ *
+ * These attribute types are used with %NL80211_STA_INFO_BSS_PARAM
+ * when getting information about the bitrate of a station.
+ *
+ * @__NL80211_STA_BSS_PARAM_INVALID: attribute number 0 is reserved
+ * @NL80211_STA_BSS_PARAM_CTS_PROT: whether CTS protection is enabled (flag)
+ * @NL80211_STA_BSS_PARAM_SHORT_PREAMBLE:  whether short preamble is enabled
+ *      (flag)
+ * @NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME:  whether short slot time is enabled
+ *      (flag)
+ * @NL80211_STA_BSS_PARAM_DTIM_PERIOD: DTIM period for beaconing (u8)
+ * @NL80211_STA_BSS_PARAM_BEACON_INTERVAL: Beacon interval (u16)
+ * @NL80211_STA_BSS_PARAM_MAX: highest sta_bss_param number currently defined
+ * @__NL80211_STA_BSS_PARAM_AFTER_LAST: internal use
+ */
+enum nl80211_sta_bss_param {
+        __NL80211_STA_BSS_PARAM_INVALID,
+        NL80211_STA_BSS_PARAM_CTS_PROT,
+        NL80211_STA_BSS_PARAM_SHORT_PREAMBLE,
+        NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME,
+        NL80211_STA_BSS_PARAM_DTIM_PERIOD,
+        NL80211_STA_BSS_PARAM_BEACON_INTERVAL,
+
+        /* keep last */
+        __NL80211_STA_BSS_PARAM_AFTER_LAST,
+        NL80211_STA_BSS_PARAM_MAX = __NL80211_STA_BSS_PARAM_AFTER_LAST - 1
+};
+
+/**
  * enum nl80211_sta_info - station information
  *
  * These attribute types are used with %NL80211_ATTR_STA_INFO
@@ -1233,7 +1387,7 @@ enum nl80211_rate_info {
  * @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (u32, to this station)
  * @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm)
  * @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute
- *      containing info as possible, see &enum nl80211_sta_info_txrate.
+ *      containing info as possible, see &enum nl80211_rate_info
  * @NL80211_STA_INFO_RX_PACKETS: total received packet (u32, from this station)
  * @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (u32, to this
  *      station)
@@ -1243,8 +1397,12 @@ enum nl80211_rate_info {
  * @NL80211_STA_INFO_LLID: the station's mesh LLID
  * @NL80211_STA_INFO_PLID: the station's mesh PLID
  * @NL80211_STA_INFO_PLINK_STATE: peer link state for the station
+ *      (see %enum nl80211_plink_state)
  * @NL80211_STA_INFO_RX_BITRATE: last unicast data frame rx rate, nested
  *      attribute, like NL80211_STA_INFO_TX_BITRATE.
+ * @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute
+ *     containing info as possible, see &enum nl80211_sta_bss_param
+ * @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected
  * @__NL80211_STA_INFO_AFTER_LAST: internal
  * @NL80211_STA_INFO_MAX: highest possible station info attribute
  */
@@ -1264,6 +1422,8 @@ enum nl80211_sta_info {
         NL80211_STA_INFO_TX_FAILED,
         NL80211_STA_INFO_SIGNAL_AVG,
         NL80211_STA_INFO_RX_BITRATE,
+        NL80211_STA_INFO_BSS_PARAM,
+        NL80211_STA_INFO_CONNECTED_TIME,
 
         /* keep last */
         __NL80211_STA_INFO_AFTER_LAST,
@@ -1686,9 +1846,21 @@ enum nl80211_meshconf_params {
  * vendor specific path metric or disable it to use the default Airtime
  * metric.
  *
- * @NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE: A vendor specific information
- * element that vendors will use to identify the path selection methods and
- * metrics in use.
+ * @NL80211_MESH_SETUP_IE: Information elements for this mesh, for instance, a
+ * robust security network ie, or a vendor specific information element that
+ * vendors will use to identify the path selection methods and metrics in use.
+ *
+ * @NL80211_MESH_SETUP_USERSPACE_AUTH: Enable this option if an authentication
+ * daemon will be authenticating mesh candidates.
+ *
+ * @NL80211_MESH_SETUP_USERSPACE_AMPE: Enable this option if an authentication
+ * daemon will be securing peer link frames.  AMPE is a secured version of Mesh
+ * Peering Management (MPM) and is implemented with the assistance of a
+ * userspace daemon.  When this flag is set, the kernel will send peer
+ * management frames to a userspace daemon that will implement AMPE
+ * functionality (security capabilities selection, key confirmation, and key
+ * management).  When the flag is unset (default), the kernel can autonomously
+ * complete (unsecured) mesh peering without the need of a userspace daemon.
  *
  * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number
  * @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use
@@ -1697,7 +1869,9 @@ enum nl80211_mesh_setup_params {
         __NL80211_MESH_SETUP_INVALID,
         NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL,
         NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC,
-        NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE,
+        NL80211_MESH_SETUP_IE,
+        NL80211_MESH_SETUP_USERSPACE_AUTH,
+        NL80211_MESH_SETUP_USERSPACE_AMPE,
 
         /* keep last */
         __NL80211_MESH_SETUP_ATTR_AFTER_LAST,
@@ -2002,4 +2176,189 @@ enum nl80211_tx_power_setting {
         NL80211_TX_POWER_FIXED,
 };
 
+/**
+ * enum nl80211_wowlan_packet_pattern_attr - WoWLAN packet pattern attribute
+ * @__NL80211_WOWLAN_PKTPAT_INVALID: invalid number for nested attribute
+ * @NL80211_WOWLAN_PKTPAT_PATTERN: the pattern, values where the mask has
+ *      a zero bit are ignored
+ * @NL80211_WOWLAN_PKTPAT_MASK: pattern mask, must be long enough to have
+ *      a bit for each byte in the pattern. The lowest-order bit corresponds
+ *      to the first byte of the pattern, but the bytes of the pattern are
+ *      in a little-endian-like format, i.e. the 9th byte of the pattern
+ *      corresponds to the lowest-order bit in the second byte of the mask.
+ *      For example: The match 00:xx:00:00:xx:00:00:00:00:xx:xx:xx (where
+ *      xx indicates "don't care") would be represented by a pattern of
+ *      twelve zero bytes, and a mask of "0xed,0x07".
+ *      Note that the pattern matching is done as though frames were not
+ *      802.11 frames but 802.3 frames, i.e. the frame is fully unpacked
+ *      first (including SNAP header unpacking) and then matched.
+ * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes
+ * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number
+ */
+enum nl80211_wowlan_packet_pattern_attr {
+        __NL80211_WOWLAN_PKTPAT_INVALID,
+        NL80211_WOWLAN_PKTPAT_MASK,
+        NL80211_WOWLAN_PKTPAT_PATTERN,
+
+        NUM_NL80211_WOWLAN_PKTPAT,
+        MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1,
+};
+
+/**
+ * struct nl80211_wowlan_pattern_support - pattern support information
+ * @max_patterns: maximum number of patterns supported
+ * @min_pattern_len: minimum length of each pattern
+ * @max_pattern_len: maximum length of each pattern
+ *
+ * This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when
+ * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the
+ * capability information given by the kernel to userspace.
+ */
+struct nl80211_wowlan_pattern_support {
+        __u32 max_patterns;
+        __u32 min_pattern_len;
+        __u32 max_pattern_len;
+} __attribute__((packed));
+
+/**
+ * enum nl80211_wowlan_triggers - WoWLAN trigger definitions
+ * @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes
+ * @NL80211_WOWLAN_TRIG_ANY: wake up on any activity, do not really put
+ *      the chip into a special state -- works best with chips that have
+ *      support for low-power operation already (flag)
+ * @NL80211_WOWLAN_TRIG_DISCONNECT: wake up on disconnect, the way disconnect
+ *      is detected is implementation-specific (flag)
+ * @NL80211_WOWLAN_TRIG_MAGIC_PKT: wake up on magic packet (6x 0xff, followed
+ *      by 16 repetitions of MAC addr, anywhere in payload) (flag)
+ * @NL80211_WOWLAN_TRIG_PKT_PATTERN: wake up on the specified packet patterns
+ *      which are passed in an array of nested attributes, each nested attribute
+ *      defining a with attributes from &struct nl80211_wowlan_trig_pkt_pattern.
+ *      Each pattern defines a wakeup packet. The matching is done on the MSDU,
+ *      i.e. as though the packet was an 802.3 packet, so the pattern matching
+ *      is done after the packet is converted to the MSDU.
+ *
+ *      In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute
+ *      carrying a &struct nl80211_wowlan_pattern_support.
+ * @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers
+ * @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number
+ */
+enum nl80211_wowlan_triggers {
+        __NL80211_WOWLAN_TRIG_INVALID,
+        NL80211_WOWLAN_TRIG_ANY,
+        NL80211_WOWLAN_TRIG_DISCONNECT,
+        NL80211_WOWLAN_TRIG_MAGIC_PKT,
+        NL80211_WOWLAN_TRIG_PKT_PATTERN,
+
+        /* keep last */
+        NUM_NL80211_WOWLAN_TRIG,
+        MAX_NL80211_WOWLAN_TRIG = NUM_NL80211_WOWLAN_TRIG - 1
+};
+
+/**
+ * enum nl80211_iface_limit_attrs - limit attributes
+ * @NL80211_IFACE_LIMIT_UNSPEC: (reserved)
+ * @NL80211_IFACE_LIMIT_MAX: maximum number of interfaces that
+ *      can be chosen from this set of interface types (u32)
+ * @NL80211_IFACE_LIMIT_TYPES: nested attribute containing a
+ *      flag attribute for each interface type in this set
+ * @NUM_NL80211_IFACE_LIMIT: number of attributes
+ * @MAX_NL80211_IFACE_LIMIT: highest attribute number
+ */
+enum nl80211_iface_limit_attrs {
+        NL80211_IFACE_LIMIT_UNSPEC,
+        NL80211_IFACE_LIMIT_MAX,
+        NL80211_IFACE_LIMIT_TYPES,
+
+        /* keep last */
+        NUM_NL80211_IFACE_LIMIT,
+        MAX_NL80211_IFACE_LIMIT = NUM_NL80211_IFACE_LIMIT - 1
+};
+
+/**
+ * enum nl80211_if_combination_attrs -- interface combination attributes
+ *
+ * @NL80211_IFACE_COMB_UNSPEC: (reserved)
+ * @NL80211_IFACE_COMB_LIMITS: Nested attributes containing the limits
+ *      for given interface types, see &enum nl80211_iface_limit_attrs.
+ * @NL80211_IFACE_COMB_MAXNUM: u32 attribute giving the total number of
+ *      interfaces that can be created in this group. This number doesn't
+ *      apply to interfaces purely managed in software, which are listed
+ *      in a separate attribute %NL80211_ATTR_INTERFACES_SOFTWARE.
+ * @NL80211_IFACE_COMB_STA_AP_BI_MATCH: flag attribute specifying that
+ *      beacon intervals within this group must be all the same even for
+ *      infrastructure and AP/GO combinations, i.e. the GO(s) must adopt
+ *      the infrastructure network's beacon interval.
+ * @NL80211_IFACE_COMB_NUM_CHANNELS: u32 attribute specifying how many
+ *      different channels may be used within this group.
+ * @NUM_NL80211_IFACE_COMB: number of attributes
+ * @MAX_NL80211_IFACE_COMB: highest attribute number
+ *
+ * Examples:
+ *      limits = [ #{STA} <= 1, #{AP} <= 1 ], matching BI, channels = 1, max = 2
+ *      => allows an AP and a STA that must match BIs
+ *
+ *      numbers = [ #{AP, P2P-GO} <= 8 ], channels = 1, max = 8
+ *      => allows 8 of AP/GO
+ *
+ *      numbers = [ #{STA} <= 2 ], channels = 2, max = 2
+ *      => allows two STAs on different channels
+ *
+ *      numbers = [ #{STA} <= 1, #{P2P-client,P2P-GO} <= 3 ], max = 4
+ *      => allows a STA plus three P2P interfaces
+ *
+ * The list of these four possiblities could completely be contained
+ * within the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute to indicate
+ * that any of these groups must match.
+ *
+ * "Combinations" of just a single interface will not be listed here,
+ * a single interface of any valid interface type is assumed to always
+ * be possible by itself. This means that implicitly, for each valid
+ * interface type, the following group always exists:
+ *      numbers = [ #{<type>} <= 1 ], channels = 1, max = 1
+ */
+enum nl80211_if_combination_attrs {
+        NL80211_IFACE_COMB_UNSPEC,
+        NL80211_IFACE_COMB_LIMITS,
+        NL80211_IFACE_COMB_MAXNUM,
+        NL80211_IFACE_COMB_STA_AP_BI_MATCH,
+        NL80211_IFACE_COMB_NUM_CHANNELS,
+
+        /* keep last */
+        NUM_NL80211_IFACE_COMB,
+        MAX_NL80211_IFACE_COMB = NUM_NL80211_IFACE_COMB - 1
+};
+
+
+/**
+ * enum nl80211_plink_state - state of a mesh peer link finite state machine
+ *
+ * @NL80211_PLINK_LISTEN: initial state, considered the implicit
+ *      state of non existant mesh peer links
+ * @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to
+ *      this mesh peer
+ * @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received
+ *      from this mesh peer
+ * @NL80211_PLINK_CNF_RCVD: mesh plink confirm frame has been
+ *      received from this mesh peer
+ * @NL80211_PLINK_ESTAB: mesh peer link is established
+ * @NL80211_PLINK_HOLDING: mesh peer link is being closed or cancelled
+ * @NL80211_PLINK_BLOCKED: all frames transmitted from this mesh
+ *      plink are discarded
+ * @NUM_NL80211_PLINK_STATES: number of peer link states
+ * @MAX_NL80211_PLINK_STATES: highest numerical value of plink states
+ */
+enum nl80211_plink_state {
+        NL80211_PLINK_LISTEN,
+        NL80211_PLINK_OPN_SNT,
+        NL80211_PLINK_OPN_RCVD,
+        NL80211_PLINK_CNF_RCVD,
+        NL80211_PLINK_ESTAB,
+        NL80211_PLINK_HOLDING,
+        NL80211_PLINK_BLOCKED,
+
+        /* keep last */
+        NUM_NL80211_PLINK_STATES,
+        MAX_NL80211_PLINK_STATES = NUM_NL80211_PLINK_STATES - 1
+};
+
 #endif /* __LINUX_NL80211_H */