1 files changed, 0 insertions, 215 deletions

diff --git a/arch/arm/plat-s3c/Kconfig b/arch/arm/plat-s3c/Kconfig
deleted file mode 100644
index 9e9d0286e48f..000000000000
--- a/arch/arm/plat-s3c/Kconfig
+++ /dev/null
@@ -1,215 +0,0 @@
-# Copyright 2007 Simtec Electronics
-#
-# Licensed under GPLv2
-
-config PLAT_S3C
-        bool
-        depends on ARCH_S3C2410 || ARCH_S3C24A0 || ARCH_S3C64XX
-        default y
-        select NO_IOPORT
-        help
-          Base platform code for any Samsung S3C device
-
-# low-level serial option nodes
-
-if PLAT_S3C
-
-config CPU_LLSERIAL_S3C2410_ONLY
-        bool
-        default y if CPU_LLSERIAL_S3C2410 && !CPU_LLSERIAL_S3C2440
-
-config CPU_LLSERIAL_S3C2440_ONLY
-        bool
-        default y if CPU_LLSERIAL_S3C2440 && !CPU_LLSERIAL_S3C2410
-
-config CPU_LLSERIAL_S3C2410
-        bool
-        help
-          Selected if there is an S3C2410 (or register compatible) serial
-          low-level implementation needed
-
-config CPU_LLSERIAL_S3C2440
-        bool
-        help
-          Selected if there is an S3C2440 (or register compatible) serial
-          low-level implementation needed
-
-# boot configurations
-
-comment "Boot options"
-
-config S3C_BOOT_WATCHDOG
-        bool "S3C Initialisation watchdog"
-        depends on S3C2410_WATCHDOG
-        help
-          Say y to enable the watchdog during the kernel decompression
-          stage. If the kernel fails to uncompress, then the watchdog
-          will trigger a reset and the system should restart.
-
-config S3C_BOOT_ERROR_RESET
-        bool "S3C Reboot on decompression error"
-        help
-          Say y here to use the watchdog to reset the system if the
-          kernel decompressor detects an error during decompression.
-
-config S3C_BOOT_UART_FORCE_FIFO
-       bool "Force UART FIFO on during boot process"
-       default y
-       help
-         Say Y here to force the UART FIFOs on during the kernel
-         uncompressor
-
-comment "Power management"
-
-config S3C2410_PM_DEBUG
-        bool "S3C2410 PM Suspend debug"
-        depends on PM
-        help
-          Say Y here if you want verbose debugging from the PM Suspend and
-          Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
-          for more information.
-
-config S3C_PM_DEBUG_LED_SMDK
-       bool "SMDK LED suspend/resume debugging"
-       depends on PM && (MACH_SMDK6410)
-       help
-         Say Y here to enable the use of the SMDK LEDs on the baseboard
-         for debugging of the state of the suspend and resume process.
-
-         Note, this currently only works for S3C64XX based SMDK boards.
-
-config S3C2410_PM_CHECK
-        bool "S3C2410 PM Suspend Memory CRC"
-        depends on PM && CRC32
-        help
-          Enable the PM code's memory area checksum over sleep. This option
-          will generate CRCs of all blocks of memory, and store them before
-          going to sleep. The blocks are then checked on resume for any
-          errors.
-
-          Note, this can take several seconds depending on memory size
-          and CPU speed.
-
-          See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
-
-config S3C2410_PM_CHECK_CHUNKSIZE
-        int "S3C2410 PM Suspend CRC Chunksize (KiB)"
-        depends on PM && S3C2410_PM_CHECK
-        default 64
-        help
-          Set the chunksize in Kilobytes of the CRC for checking memory
-          corruption over suspend and resume. A smaller value will mean that
-          the CRC data block will take more memory, but wil identify any
-          faults with better precision.
-
-          See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
-
-config S3C_LOWLEVEL_UART_PORT
-        int "S3C UART to use for low-level messages"
-        default 0
-        help
-          Choice of which UART port to use for the low-level messages,
-          such as the `Uncompressing...` at start time. The value of
-          this configuration should be between zero and two. The port
-          must have been initialised by the boot-loader before use.
-
-# options for gpiolib support
-
-config S3C_GPIO_SPACE
-        int "Space between gpio banks"
-        default 0
-        help
-          Add a number of spare GPIO entries between each bank for debugging
-          purposes. This allows any problems where an counter overflows from
-          one bank to another to be caught, at the expense of using a little
-          more memory.
-
-config S3C_GPIO_TRACK
-        bool
-        help
-          Internal configuration option to enable the s3c specific gpio
-          chip tracking if the platform requires it.
-
-config S3C_GPIO_PULL_UPDOWN
-        bool
-        help
-          Internal configuration to enable the correct GPIO pull helper
-
-config S3C_GPIO_PULL_DOWN
-        bool
-        help
-          Internal configuration to enable the correct GPIO pull helper
-
-config S3C_GPIO_PULL_UP
-        bool
-        help
-          Internal configuration to enable the correct GPIO pull helper
-
-config S3C_GPIO_CFG_S3C24XX
-        bool
-        help
-          Internal configuration to enable S3C24XX style GPIO configuration
-          functions.
-
-config S3C_GPIO_CFG_S3C64XX
-        bool
-        help
-          Internal configuration to enable S3C64XX style GPIO configuration
-          functions.
-
-config S5P_GPIO_CFG_S5PC1XX
-        bool
-        help
-          Internal configuration to enable S5PC1XX style GPIO configuration
-          functions.
-
-# DMA
-
-config S3C_DMA
-        bool
-        help
-          Internal configuration for S3C DMA core
-
-# device definitions to compile in
-
-config S3C_DEV_HSMMC
-        bool
-        help
-          Compile in platform device definitions for HSMMC code
-
-config S3C_DEV_HSMMC1
-        bool
-        help
-          Compile in platform device definitions for HSMMC channel 1
-
-config S3C_DEV_HSMMC2
-        bool
-        help
-          Compile in platform device definitions for HSMMC channel 2
-
-config S3C_DEV_I2C1
-        bool
-        help
-          Compile in platform device definitions for I2C channel 1
-
-config S3C_DEV_FB
-        bool
-        help
-          Compile in platform device definition for framebuffer
-
-config S3C_DEV_USB_HOST
-        bool
-        help
-          Compile in platform device definition for USB host.
-
-config S3C_DEV_USB_HSOTG
-        bool
-        help
-          Compile in platform device definition for USB high-speed OtG
-
-config S3C_DEV_NAND
-        bool
-        help
-          Compile in platform device definition for NAND controller
-
-endif