33 files changed, 870 insertions, 19 deletions

diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
index bfbc771a65f8..ac9e7516756e 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -1,6 +1,14 @@
 Freescale i.MX Platforms Device Tree Bindings
 -----------------------------------------------
 
+i.MX23 Evaluation Kit
+Required root node properties:
+    - compatible = "fsl,imx23-evk", "fsl,imx23";
+
+i.MX28 Evaluation Kit
+Required root node properties:
+    - compatible = "fsl,imx28-evk", "fsl,imx28";
+
 i.MX51 Babbage Board
 Required root node properties:
     - compatible = "fsl,imx51-babbage", "fsl,imx51";
@@ -29,6 +37,10 @@ i.MX6 Quad SABRE Lite Board
 Required root node properties:
     - compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
 
+i.MX6 Quad SABRE Smart Device Board
+Required root node properties:
+    - compatible = "fsl,imx6q-sabresd", "fsl,imx6q";
+
 Generic i.MX boards
 -------------------
 
diff --git a/Documentation/devicetree/bindings/arm/samsung/interrupt-combiner.txt b/Documentation/devicetree/bindings/arm/samsung/interrupt-combiner.txt
new file mode 100644
index 000000000000..f2f2171e530e
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/samsung/interrupt-combiner.txt
@@ -0,0 +1,52 @@
+* Samsung Exynos Interrupt Combiner Controller
+
+Samsung's Exynos4 architecture includes a interrupt combiner controller which
+can combine interrupt sources as a group and provide a single interrupt request
+for the group. The interrupt request from each group are connected to a parent
+interrupt controller, such as GIC in case of Exynos4210.
+
+The interrupt combiner controller consists of multiple combiners. Upto eight
+interrupt sources can be connected to a combiner. The combiner outputs one
+combined interrupt for its eight interrupt sources. The combined interrupt
+is usually connected to a parent interrupt controller.
+
+A single node in the device tree is used to describe the interrupt combiner
+controller module (which includes multiple combiners). A combiner in the
+interrupt controller module shares config/control registers with other
+combiners. For example, a 32-bit interrupt enable/disable config register
+can accommodate upto 4 interrupt combiners (with each combiner supporting
+upto 8 interrupt sources).
+
+Required properties:
+- compatible: should be "samsung,exynos4210-combiner".
+- interrupt-controller: Identifies the node as an interrupt controller.
+- #interrupt-cells: should be <2>. The meaning of the cells are
+        * First Cell: Combiner Group Number.
+        * Second Cell: Interrupt number within the group.
+- reg: Base address and size of interrupt combiner registers.
+- interrupts: The list of interrupts generated by the combiners which are then
+    connected to a parent interrupt controller. The format of the interrupt
+    specifier depends in the interrupt parent controller.
+
+Optional properties:
+- samsung,combiner-nr: The number of interrupt combiners supported. If this
+  property is not specified, the default number of combiners is assumed
+  to be 16.
+- interrupt-parent: pHandle of the parent interrupt controller, if not
+  inherited from the parent node.
+
+
+Example:
+
+        The following is a an example from the Exynos4210 SoC dtsi file.
+
+        combiner:interrupt-controller@10440000 {
+                compatible = "samsung,exynos4210-combiner";
+                interrupt-controller;
+                #interrupt-cells = <2>;
+                reg = <0x10440000 0x1000>;
+                interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
+                             <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
+                             <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
+                             <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
+        };
diff --git a/Documentation/devicetree/bindings/arm/spear-timer.txt b/Documentation/devicetree/bindings/arm/spear-timer.txt
new file mode 100644
index 000000000000..c0017221cf55
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/spear-timer.txt
@@ -0,0 +1,18 @@
+* SPEAr ARM Timer
+
+** Timer node required properties:
+
+- compatible : Should be:
+        "st,spear-timer"
+- reg: Address range of the timer registers
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupt: Should contain the timer interrupt number
+
+Example:
+
+        timer@f0000000 {
+                compatible = "st,spear-timer";
+                reg = <0xf0000000 0x400>;
+                interrupts = <2>;
+        };
diff --git a/Documentation/devicetree/bindings/arm/spear.txt b/Documentation/devicetree/bindings/arm/spear.txt
index aa5f355cc947..0d42949df6c2 100644
--- a/Documentation/devicetree/bindings/arm/spear.txt
+++ b/Documentation/devicetree/bindings/arm/spear.txt
@@ -2,25 +2,25 @@ ST SPEAr Platforms Device Tree Bindings
 ---------------------------------------
 
 Boards with the ST SPEAr600 SoC shall have the following properties:
-
 Required root node property:
-
 compatible = "st,spear600";
 
 Boards with the ST SPEAr300 SoC shall have the following properties:
-
 Required root node property:
-
 compatible = "st,spear300";
 
 Boards with the ST SPEAr310 SoC shall have the following properties:
-
 Required root node property:
-
 compatible = "st,spear310";
 
 Boards with the ST SPEAr320 SoC shall have the following properties:
+Required root node property:
+compatible = "st,spear320";
 
+Boards with the ST SPEAr1310 SoC shall have the following properties:
 Required root node property:
+compatible = "st,spear1310";
 
-compatible = "st,spear320";
+Boards with the ST SPEAr1340 SoC shall have the following properties:
+Required root node property:
+compatible = "st,spear1340";
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-ahb.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-ahb.txt
new file mode 100644
index 000000000000..234406d41c12
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-ahb.txt
@@ -0,0 +1,11 @@
+NVIDIA Tegra AHB
+
+Required properties:
+- compatible : "nvidia,tegra20-ahb" or "nvidia,tegra30-ahb"
+- reg : Should contain 1 register ranges(address and length)
+
+Example:
+        ahb: ahb@6000c004 {
+                compatible = "nvidia,tegra20-ahb";
+                reg = <0x6000c004 0x10c>; /* AHB Arbitration + Gizmo Controller */
+        };
diff --git a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt
new file mode 100644
index 000000000000..ded0398d3bdc
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt
@@ -0,0 +1,19 @@
+* Freescale MXS DMA
+
+Required properties:
+- compatible : Should be "fsl,<chip>-dma-apbh" or "fsl,<chip>-dma-apbx"
+- reg : Should contain registers location and length
+
+Supported chips:
+imx23, imx28.
+
+Examples:
+dma-apbh@80004000 {
+        compatible = "fsl,imx28-dma-apbh";
+        reg = <0x80004000 2000>;
+};
+
+dma-apbx@80024000 {
+        compatible = "fsl,imx28-dma-apbx";
+        reg = <0x80024000 2000>;
+};
diff --git a/Documentation/devicetree/bindings/dma/snps-dma.txt b/Documentation/devicetree/bindings/dma/snps-dma.txt
new file mode 100644
index 000000000000..c0d85dbcada5
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/snps-dma.txt
@@ -0,0 +1,17 @@
+* Synopsys Designware DMA Controller
+
+Required properties:
+- compatible: "snps,dma-spear1340"
+- reg: Address range of the DMAC registers
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupt: Should contain the DMAC interrupt number
+
+Example:
+
+        dma@fc000000 {
+                compatible = "snps,dma-spear1340";
+                reg = <0xfc000000 0x1000>;
+                interrupt-parent = <&vic1>;
+                interrupts = <12>;
+        };
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt b/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt
new file mode 100644
index 000000000000..f93d51478d5a
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt
@@ -0,0 +1,38 @@
+Lantiq SoC External Bus memory mapped GPIO controller
+
+By attaching hardware latches to the EBU it is possible to create output
+only gpios. This driver configures a special memory address, which when
+written to outputs 16 bit to the latches.
+
+The node describing the memory mapped GPIOs needs to be a child of the node
+describing the "lantiq,localbus".
+
+Required properties:
+- compatible : Should be "lantiq,gpio-mm-lantiq"
+- reg : Address and length of the register set for the device
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- gpio-controller : Marks the device node as a gpio controller.
+
+Optional properties:
+- lantiq,shadow : The default value that we shall assume as already set on the
+  shift register cascade.
+
+Example:
+
+localbus@0 {
+        #address-cells = <2>;
+        #size-cells = <1>;
+        ranges = <0 0 0x0 0x3ffffff /* addrsel0 */
+                1 0 0x4000000 0x4000010>; /* addsel1 */
+        compatible = "lantiq,localbus", "simple-bus";
+
+        gpio_mm0: gpio@4000000 {
+                compatible = "lantiq,gpio-mm";
+                reg = <1 0x0 0x10>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                lantiq,shadow = <0x77f>
+        };
+}
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mxs.txt b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt
new file mode 100644
index 000000000000..0c35673f7a3e
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt
@@ -0,0 +1,87 @@
+* Freescale MXS GPIO controller
+
+The Freescale MXS GPIO controller is part of MXS PIN controller.  The
+GPIOs are organized in port/bank.  Each port consists of 32 GPIOs.
+
+As the GPIO controller is embedded in the PIN controller and all the
+GPIO ports share the same IO space with PIN controller, the GPIO node
+will be represented as sub-nodes of MXS pinctrl node.
+
+Required properties for GPIO node:
+- compatible : Should be "fsl,<soc>-gpio".  The supported SoCs include
+  imx23 and imx28.
+- interrupts : Should be the port interrupt shared by all 32 pins.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells : Should be 2.  The first cell is the GPIO number.
+  The second cell bits[3:0] is used to specify trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+
+Note: Each GPIO port should have an alias correctly numbered in "aliases"
+node.
+
+Examples:
+
+aliases {
+        gpio0 = &gpio0;
+        gpio1 = &gpio1;
+        gpio2 = &gpio2;
+        gpio3 = &gpio3;
+        gpio4 = &gpio4;
+};
+
+pinctrl@80018000 {
+        compatible = "fsl,imx28-pinctrl", "simple-bus";
+        reg = <0x80018000 2000>;
+
+        gpio0: gpio@0 {
+                compatible = "fsl,imx28-gpio";
+                interrupts = <127>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+        };
+
+        gpio1: gpio@1 {
+                compatible = "fsl,imx28-gpio";
+                interrupts = <126>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+        };
+
+        gpio2: gpio@2 {
+                compatible = "fsl,imx28-gpio";
+                interrupts = <125>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+        };
+
+        gpio3: gpio@3 {
+                compatible = "fsl,imx28-gpio";
+                interrupts = <124>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+        };
+
+        gpio4: gpio@4 {
+                compatible = "fsl,imx28-gpio";
+                interrupts = <123>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+        };
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt
new file mode 100644
index 000000000000..854de130a971
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt
@@ -0,0 +1,42 @@
+Lantiq SoC Serial To Parallel (STP) GPIO controller
+
+The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a
+peripheral controller used to drive external shift register cascades. At most
+3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem
+to drive the 2 LSBs of the cascade automatically.
+
+
+Required properties:
+- compatible : Should be "lantiq,gpio-stp-xway"
+- reg : Address and length of the register set for the device
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- gpio-controller : Marks the device node as a gpio controller.
+
+Optional properties:
+- lantiq,shadow : The default value that we shall assume as already set on the
+  shift register cascade.
+- lantiq,groups : Set the 3 bit mask to select which of the 3 groups are enabled
+  in the shift register cascade.
+- lantiq,dsl : The dsl core can control the 2 LSBs of the gpio cascade. This 2 bit
+  property can enable this feature.
+- lantiq,phy1 : The gphy1 core can control 3 bits of the gpio cascade.
+- lantiq,phy2 : The gphy2 core can control 3 bits of the gpio cascade.
+- lantiq,rising : use rising instead of falling edge for the shift register
+
+Example:
+
+gpio1: stp@E100BB0 {
+        compatible = "lantiq,gpio-stp-xway";
+        reg = <0xE100BB0 0x40>;
+        #gpio-cells = <2>;
+        gpio-controller;
+
+        lantiq,shadow = <0xffff>;
+        lantiq,groups = <0x7>;
+        lantiq,dsl = <0x3>;
+        lantiq,phy1 = <0x7>;
+        lantiq,phy2 = <0x7>;
+        /* lantiq,rising; */
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt
new file mode 100644
index 000000000000..1bfc02de1b0c
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt
@@ -0,0 +1,16 @@
+* Freescale MXS Inter IC (I2C) Controller
+
+Required properties:
+- compatible: Should be "fsl,<chip>-i2c"
+- reg: Should contain registers location and length
+- interrupts: Should contain ERROR and DMA interrupts
+
+Examples:
+
+i2c0: i2c@80058000 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        compatible = "fsl,imx28-i2c";
+        reg = <0x80058000 2000>;
+        interrupts = <111 68>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/mux.txt b/Documentation/devicetree/bindings/i2c/mux.txt
new file mode 100644
index 000000000000..af84cce5cd7b
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/mux.txt
@@ -0,0 +1,60 @@
+Common i2c bus multiplexer/switch properties.
+
+An i2c bus multiplexer/switch will have several child busses that are
+numbered uniquely in a device dependent manner.  The nodes for an i2c bus
+multiplexer/switch will have one child node for each child
+bus.
+
+Required properties:
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Required properties for child nodes:
+- #address-cells = <1>;
+- #size-cells = <0>;
+- reg : The sub-bus number.
+
+Optional properties for child nodes:
+- Other properties specific to the multiplexer/switch hardware.
+- Child nodes conforming to i2c bus binding
+
+
+Example :
+
+        /*
+           An NXP pca9548 8 channel I2C multiplexer at address 0x70
+           with two NXP pca8574 GPIO expanders attached, one each to
+           ports 3 and 4.
+         */
+
+        mux@70 {
+                compatible = "nxp,pca9548";
+                reg = <0x70>;
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                i2c@3 {
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+                        reg = <3>;
+
+                        gpio1: gpio@38 {
+                                compatible = "nxp,pca8574";
+                                reg = <0x38>;
+                                #gpio-cells = <2>;
+                                gpio-controller;
+                        };
+                };
+                i2c@4 {
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+                        reg = <4>;
+
+                        gpio2: gpio@38 {
+                                compatible = "nxp,pca8574";
+                                reg = <0x38>;
+                                #gpio-cells = <2>;
+                                gpio-controller;
+                        };
+                };
+        };
diff --git a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt
index 38832c712919..b6cb5a12c672 100644
--- a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt
+++ b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt
@@ -6,14 +6,18 @@ Required properties:
   - compatible: value should be either of the following.
       (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c.
       (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c.
+      (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used
+          inside HDMIPHY block found on several samsung SoCs
   - reg: physical base address of the controller and length of memory mapped
     region.
   - interrupts: interrupt number to the cpu.
   - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges.
-  - gpios: The order of the gpios should be the following: <SDA, SCL>.
-    The gpio specifier depends on the gpio controller.
 
 Optional properties:
+  - gpios: The order of the gpios should be the following: <SDA, SCL>.
+    The gpio specifier depends on the gpio controller. Required in all
+    cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
+    lines are permanently wired to the respective client
   - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not
     specified, default value is 0.
   - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
diff --git a/Documentation/devicetree/bindings/i2c/xiic.txt b/Documentation/devicetree/bindings/i2c/xiic.txt
new file mode 100644
index 000000000000..ceabbe91ae44
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/xiic.txt
@@ -0,0 +1,22 @@
+Xilinx IIC controller:
+
+Required properties:
+- compatible : Must be "xlnx,xps-iic-2.00.a"
+- reg : IIC register location and length
+- interrupts : IIC controller unterrupt
+- #address-cells = <1>
+- #size-cells = <0>
+
+Optional properties:
+- Child nodes conforming to i2c bus binding
+
+Example:
+
+        axi_iic_0: i2c@40800000 {
+                compatible = "xlnx,xps-iic-2.00.a";
+                interrupts = < 1 2 >;
+                reg = < 0x40800000 0x10000 >;
+
+                #size-cells = <0>;
+                #address-cells = <1>;
+        };
diff --git a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt
new file mode 100644
index 000000000000..1857f4a6b9a9
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt
@@ -0,0 +1,60 @@
+* Dialog DA9052/53 Power Management Integrated Circuit (PMIC)
+
+Required properties:
+- compatible : Should be "dlg,da9052", "dlg,da9053-aa",
+                         "dlg,da9053-ab", or "dlg,da9053-bb"
+
+Sub-nodes:
+- regulators : Contain the regulator nodes. The DA9052/53 regulators are
+  bound using their names as listed below:
+
+    buck0     : regulator BUCK0
+    buck1     : regulator BUCK1
+    buck2     : regulator BUCK2
+    buck3     : regulator BUCK3
+    ldo4      : regulator LDO4
+    ldo5      : regulator LDO5
+    ldo6      : regulator LDO6
+    ldo7      : regulator LDO7
+    ldo8      : regulator LDO8
+    ldo9      : regulator LDO9
+    ldo10     : regulator LDO10
+    ldo11     : regulator LDO11
+    ldo12     : regulator LDO12
+    ldo13     : regulator LDO13
+
+  The bindings details of individual regulator device can be found in:
+  Documentation/devicetree/bindings/regulator/regulator.txt
+
+Examples:
+
+i2c@63fc8000 { /* I2C1 */
+        status = "okay";
+
+        pmic: dialog@48 {
+                compatible = "dlg,da9053-aa";
+                reg = <0x48>;
+
+                regulators {
+                        buck0 {
+                                regulator-min-microvolt = <500000>;
+                                regulator-max-microvolt = <2075000>;
+                        };
+
+                        buck1 {
+                                regulator-min-microvolt = <500000>;
+                                regulator-max-microvolt = <2075000>;
+                        };
+
+                        buck2 {
+                                regulator-min-microvolt = <925000>;
+                                regulator-max-microvolt = <2500000>;
+                        };
+
+                        buck3 {
+                                regulator-min-microvolt = <925000>;
+                                regulator-max-microvolt = <2500000>;
+                        };
+                };
+        };
+};
diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt
new file mode 100644
index 000000000000..645f5eaadb3f
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/tps65910.txt
@@ -0,0 +1,133 @@
+TPS65910 Power Management Integrated Circuit
+
+Required properties:
+- compatible: "ti,tps65910" or "ti,tps65911"
+- reg: I2C slave address
+- interrupts: the interrupt outputs of the controller
+- #gpio-cells: number of cells to describe a GPIO, this should be 2.
+  The first cell is the GPIO number.
+  The second cell is used to specify additional options <unused>.
+- gpio-controller: mark the device as a GPIO controller
+- #interrupt-cells: the number of cells to describe an IRQ, this should be 2.
+  The first cell is the IRQ number.
+  The second cell is the flags, encoded as the trigger masks from
+  Documentation/devicetree/bindings/interrupts.txt
+- regulators: This is the list of child nodes that specify the regulator
+  initialization data for defined regulators. Not all regulators for the given
+  device need to be present. The definition for each of these nodes is defined
+  using the standard binding for regulators found at
+  Documentation/devicetree/bindings/regulator/regulator.txt.
+
+  The valid names for regulators are:
+  tps65910: vrtc, vio, vdd1, vdd2, vdd3, vdig1, vdig2, vpll, vdac, vaux1,
+            vaux2, vaux33, vmmc
+  tps65911: vrtc, vio, vdd1, vdd3, vddctrl, ldo1, ldo2, ldo3, ldo4, ldo5,
+            ldo6, ldo7, ldo8
+
+Optional properties:
+- ti,vmbch-threshold: (tps65911) main battery charged threshold
+  comparator. (see VMBCH_VSEL in TPS65910 datasheet)
+- ti,vmbch2-threshold: (tps65911) main battery discharged threshold
+  comparator. (see VMBCH_VSEL in TPS65910 datasheet)
+- ti,en-gpio-sleep: enable sleep control for gpios
+  There should be 9 entries here, one for each gpio.
+
+Regulator Optional properties:
+- ti,regulator-ext-sleep-control: enable external sleep
+  control through external inputs [0 (not enabled), 1 (EN1), 2 (EN2) or 4(EN3)]
+  If this property is not defined, it defaults to 0 (not enabled).
+
+Example:
+
+        pmu: tps65910@d2 {
+                compatible = "ti,tps65910";
+                reg = <0xd2>;
+                interrupt-parent = <&intc>;
+                interrupts = < 0 118 0x04 >;
+
+                #gpio-cells = <2>;
+                gpio-controller;
+
+                #interrupt-cells = <2>;
+                interrupt-controller;
+
+                ti,vmbch-threshold = 0;
+                ti,vmbch2-threshold = 0;
+
+                ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>;
+
+                regulators {
+                        vdd1_reg: vdd1 {
+                                regulator-min-microvolt = < 600000>;
+                                regulator-max-microvolt = <1500000>;
+                                regulator-always-on;
+                                regulator-boot-on;
+                                ti,regulator-ext-sleep-control = <0>;
+                        };
+                        vdd2_reg: vdd2 {
+                                regulator-min-microvolt = < 600000>;
+                                regulator-max-microvolt = <1500000>;
+                                regulator-always-on;
+                                regulator-boot-on;
+                                ti,regulator-ext-sleep-control = <4>;
+                        };
+                        vddctrl_reg: vddctrl {
+                                regulator-min-microvolt = < 600000>;
+                                regulator-max-microvolt = <1400000>;
+                                regulator-always-on;
+                                regulator-boot-on;
+                                ti,regulator-ext-sleep-control = <0>;
+                        };
+                        vio_reg: vio {
+                                regulator-min-microvolt = <1500000>;
+                                regulator-max-microvolt = <1800000>;
+                                regulator-always-on;
+                                regulator-boot-on;
+                                ti,regulator-ext-sleep-control = <1>;
+                        };
+                        ldo1_reg: ldo1 {
+                                regulator-min-microvolt = <1000000>;
+                                regulator-max-microvolt = <3300000>;
+                                ti,regulator-ext-sleep-control = <0>;
+                        };
+                        ldo2_reg: ldo2 {
+                                regulator-min-microvolt = <1050000>;
+                                regulator-max-microvolt = <1050000>;
+                                ti,regulator-ext-sleep-control = <0>;
+                        };
+                        ldo3_reg: ldo3 {
+                                regulator-min-microvolt = <1000000>;
+                                regulator-max-microvolt = <3300000>;
+                                ti,regulator-ext-sleep-control = <0>;
+                        };
+                        ldo4_reg: ldo4 {
+                                regulator-min-microvolt = <1000000>;
+                                regulator-max-microvolt = <3300000>;
+                                regulator-always-on;
+                                ti,regulator-ext-sleep-control = <0>;
+                        };
+                        ldo5_reg: ldo5 {
+                                regulator-min-microvolt = <1000000>;
+                                regulator-max-microvolt = <3300000>;
+                                ti,regulator-ext-sleep-control = <0>;
+                        };
+                        ldo6_reg: ldo6 {
+                                regulator-min-microvolt = <1200000>;
+                                regulator-max-microvolt = <1200000>;
+                                ti,regulator-ext-sleep-control = <0>;
+                        };
+                        ldo7_reg: ldo7 {
+                                regulator-min-microvolt = <1200000>;
+                                regulator-max-microvolt = <1200000>;
+                                regulator-always-on;
+                                regulator-boot-on;
+                                ti,regulator-ext-sleep-control = <1>;
+                        };
+                        ldo8_reg: ldo8 {
+                                regulator-min-microvolt = <1000000>;
+                                regulator-max-microvolt = <3300000>;
+                                regulator-always-on;
+                                ti,regulator-ext-sleep-control = <1>;
+                        };
+                };
+        };
diff --git a/Documentation/devicetree/bindings/mfd/twl6040.txt b/Documentation/devicetree/bindings/mfd/twl6040.txt
new file mode 100644
index 000000000000..bc67c6f424aa
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/twl6040.txt
@@ -0,0 +1,62 @@
+Texas Instruments TWL6040 family
+
+The TWL6040s are 8-channel high quality low-power audio codecs providing audio
+and vibra functionality on OMAP4+ platforms.
+They are connected ot the host processor via i2c for commands, McPDM for audio
+data and commands.
+
+Required properties:
+- compatible : Must be "ti,twl6040";
+- reg: must be 0x4b for i2c address
+- interrupts: twl6040 has one interrupt line connecteded to the main SoC
+- interrupt-parent: The parent interrupt controller
+- twl6040,audpwron-gpio: Power on GPIO line for the twl6040
+
+- vio-supply: Regulator for the twl6040 VIO supply
+- v2v1-supply: Regulator for the twl6040 V2V1 supply
+
+Optional properties, nodes:
+- enable-active-high: To power on the twl6040 during boot.
+
+Vibra functionality
+Required properties:
+- vddvibl-supply: Regulator for the left vibra motor
+- vddvibr-supply: Regulator for the right vibra motor
+- vibra { }: Configuration section for vibra parameters containing the following
+             properties:
+- ti,vibldrv-res: Resistance parameter for left driver
+- ti,vibrdrv-res: Resistance parameter for right driver
+- ti,viblmotor-res: Resistance parameter for left motor
+- ti,viblmotor-res: Resistance parameter for right motor
+
+Optional properties within vibra { } section:
+- vddvibl_uV: If the vddvibl default voltage need to be changed
+- vddvibr_uV: If the vddvibr default voltage need to be changed
+
+Example:
+&i2c1 {
+        twl6040: twl@4b {
+                compatible = "ti,twl6040";
+                reg = <0x4b>;
+
+                interrupts = <0 119 4>;
+                interrupt-parent = <&gic>;
+                twl6040,audpwron-gpio = <&gpio4 31 0>;
+
+                vio-supply = <&v1v8>;
+                v2v1-supply = <&v2v1>;
+                enable-active-high;
+
+                /* regulators for vibra motor */
+                vddvibl-supply = <&vbat>;
+                vddvibr-supply = <&vbat>;
+
+                vibra {
+                        /* Vibra driver, motor resistance parameters */
+                        ti,vibldrv-res = <8>;
+                        ti,vibrdrv-res = <3>;
+                        ti,viblmotor-res = <10>;
+                        ti,vibrmotor-res = <10>;
+                };
+        };
+};
diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
index 64bcb8be973c..0d93b4b0e0e3 100644
--- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
+++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
@@ -11,9 +11,11 @@ Required properties:
   - interrupt-parent : interrupt source phandle.
   - clock-frequency : specifies eSDHC base clock frequency.
   - sdhci,wp-inverted : (optional) specifies that eSDHC controller
-    reports inverted write-protect state;
+    reports inverted write-protect state; New devices should use
+    the generic "wp-inverted" property.
   - sdhci,1-bit-only : (optional) specifies that a controller can
-    only handle 1-bit data transfers.
+    only handle 1-bit data transfers. New devices should use the
+    generic "bus-width = <1>" property.
   - sdhci,auto-cmd12: (optional) specifies that a controller can
     only handle auto CMD12.
 
diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
index ab22fe6e73ab..c7e404b3ef05 100644
--- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
+++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
@@ -9,7 +9,7 @@ Required properties:
 - interrupts : Should contain eSDHC interrupt
 
 Optional properties:
-- fsl,card-wired : Indicate the card is wired to host permanently
+- non-removable : Indicate the card is wired to host permanently
 - fsl,cd-internal : Indicate to use controller internal card detection
 - fsl,wp-internal : Indicate to use controller internal write protection
 - cd-gpios : Specify GPIOs for card detection
diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt
index 89a0084df2f7..d64aea5a4203 100644
--- a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt
+++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt
@@ -10,7 +10,8 @@ Required properties:
 
 Optional properties:
 - gpios : may specify GPIOs in this order: Card-Detect GPIO,
-  Write-Protect GPIO.
+  Write-Protect GPIO. Note that this does not follow the
+  binding from mmc.txt, for historic reasons.
 - interrupts : the interrupt of a card detect interrupt.
 - interrupt-parent : the phandle for the interrupt controller that
   services interrupts for this device.
diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
new file mode 100644
index 000000000000..6e70dcde0a71
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/mmc.txt
@@ -0,0 +1,27 @@
+These properties are common to multiple MMC host controllers. Any host
+that requires the respective functionality should implement them using
+these definitions.
+
+Required properties:
+- bus-width: Number of data lines, can be <1>, <4>, or <8>
+
+Optional properties:
+- cd-gpios : Specify GPIOs for card detection, see gpio binding
+- wp-gpios : Specify GPIOs for write protection, see gpio binding
+- cd-inverted: when present, polarity on the wp gpio line is inverted
+- wp-inverted: when present, polarity on the wp gpio line is inverted
+- non-removable: non-removable slot (like eMMC)
+- max-frequency: maximum operating clock frequency
+
+Example:
+
+sdhci@ab000000 {
+        compatible = "sdhci";
+        reg = <0xab000000 0x200>;
+        interrupts = <23>;
+        bus-width = <4>;
+        cd-gpios = <&gpio 69 0>;
+        cd-inverted;
+        wp-gpios = <&gpio 70 0>;
+        max-frequency = <50000000>;
+}
diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt
new file mode 100644
index 000000000000..14a81d526118
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/mmci.txt
@@ -0,0 +1,19 @@
+* ARM PrimeCell MultiMedia Card Interface (MMCI) PL180/1
+
+The ARM PrimeCell MMCI PL180 and PL181 provides and interface for
+reading and writing to MultiMedia and SD cards alike.
+
+Required properties:
+- compatible             : contains "arm,pl18x", "arm,primecell".
+- reg                    : contains pl18x registers and length.
+- interrupts             : contains the device IRQ(s).
+- arm,primecell-periphid : contains the PrimeCell Peripheral ID.
+
+Optional properties:
+- wp-gpios               : contains any write protect (ro) gpios
+- cd-gpios               : contains any card detection gpios
+- cd-inverted            : indicates whether the cd gpio is inverted
+- max-frequency          : contains the maximum operating frequency
+- bus-width              : number of data lines, can be <1>, <4>, or <8>
+- mmc-cap-mmc-highspeed  : indicates whether MMC is high speed capable
+- mmc-cap-sd-highspeed   : indicates whether SD is high speed capable
diff --git a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt
new file mode 100644
index 000000000000..14d870a9e3db
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt
@@ -0,0 +1,25 @@
+* Freescale MXS MMC controller
+
+The Freescale MXS Synchronous Serial Ports (SSP) can act as a MMC controller
+to support MMC, SD, and SDIO types of memory cards.
+
+Required properties:
+- compatible: Should be "fsl,<chip>-mmc".  The supported chips include
+  imx23 and imx28.
+- reg: Should contain registers location and length
+- interrupts: Should contain ERROR and DMA interrupts
+- fsl,ssp-dma-channel: APBH DMA channel for the SSP
+- bus-width: Number of data lines, can be <1>, <4>, or <8>
+
+Optional properties:
+- wp-gpios: Specify GPIOs for write protection
+
+Examples:
+
+ssp0: ssp@80010000 {
+        compatible = "fsl,imx28-mmc";
+        reg = <0x80010000 2000>;
+        interrupts = <96 82>;
+        fsl,ssp-dma-channel = <0>;
+        bus-width = <8>;
+};
diff --git a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt
index 7e51154679a6..f77c3031607f 100644
--- a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt
+++ b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt
@@ -7,12 +7,12 @@ Required properties:
 - compatible : Should be "nvidia,<chip>-sdhci"
 - reg : Should contain SD/MMC registers location and length
 - interrupts : Should contain SD/MMC interrupt
+- bus-width : Number of data lines, can be <1>, <4>, or <8>
 
 Optional properties:
 - cd-gpios : Specify GPIOs for card detection
 - wp-gpios : Specify GPIOs for write protection
 - power-gpios : Specify GPIOs for power control
-- support-8bit : Boolean, indicates if 8-bit mode should be used.
 
 Example:
 
@@ -23,5 +23,5 @@ sdhci@c8000200 {
         cd-gpios = <&gpio 69 0>; /* gpio PI5 */
         wp-gpios = <&gpio 57 0>; /* gpio PH1 */
         power-gpios = <&gpio 155 0>; /* gpio PT3 */
-        support-8bit;
+        bus-width = <8>;
 };
diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
index dbd4368ab8cc..8a53958c9a9f 100644
--- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
+++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
@@ -15,7 +15,7 @@ Optional properties:
 ti,dual-volt: boolean, supports dual voltage cards
 <supply-name>-supply: phandle to the regulator device tree node
 "supply-name" examples are "vmmc", "vmmc_aux" etc
-ti,bus-width: Number of data lines, default assumed is 1 if the property is missing.
+bus-width: Number of data lines, default assumed is 1 if the property is missing.
 cd-gpios: GPIOs for card detection
 wp-gpios: GPIOs for write protection
 ti,non-removable: non-removable slot (like eMMC)
@@ -27,7 +27,7 @@ Example:
                 reg = <0x4809c000 0x400>;
                 ti,hwmods = "mmc1";
                 ti,dual-volt;
-                ti,bus-width = <4>;
+                bus-width = <4>;
                 vmmc-supply = <&vmmc>; /* phandle to regulator node */
                 ti,non-removable;
         };
diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt
index de439517dff0..7ab9e1a2d8be 100644
--- a/Documentation/devicetree/bindings/net/fsl-fec.txt
+++ b/Documentation/devicetree/bindings/net/fsl-fec.txt
@@ -14,7 +14,7 @@ Optional properties:
 
 Example:
 
-fec@83fec000 {
+ethernet@83fec000 {
         compatible = "fsl,imx51-fec", "fsl,imx27-fec";
         reg = <0x83fec000 0x4000>;
         interrupts = <87>;
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt
index 3664d37e6799..b4480d5c3aca 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt
@@ -4,6 +4,8 @@ Required properties:
 - compatible    : "st,spear300-pinmux"
                 : "st,spear310-pinmux"
                 : "st,spear320-pinmux"
+                : "st,spear1310-pinmux"
+                : "st,spear1340-pinmux"
 - reg           : Address range of the pinctrl registers
 - st,pinmux-mode: Mandatory for SPEAr300 and SPEAr320 and invalid for others.
         - Its values for SPEAr300:
@@ -89,6 +91,37 @@ For SPEAr320 machines:
         "rmii0_1_grp", "i2c1_8_9_grp", "i2c1_98_99_grp", "i2c2_0_1_grp",
         "i2c2_2_3_grp", "i2c2_19_20_grp", "i2c2_75_76_grp", "i2c2_96_97_grp"
 
+For SPEAr1310 machines:
+        "i2c0_grp", "ssp0_grp", "ssp0_cs0_grp", "ssp0_cs1_2_grp", "i2s0_grp",
+        "i2s1_grp", "clcd_grp", "clcd_high_res_grp", "arm_gpio_grp",
+        "smi_2_chips_grp", "smi_4_chips_grp", "gmii_grp", "rgmii_grp",
+        "smii_0_1_2_grp", "ras_mii_txclk_grp", "nand_8bit_grp",
+        "nand_16bit_grp", "nand_4_chips_grp", "keyboard_6x6_grp",
+        "keyboard_rowcol6_8_grp", "uart0_grp", "uart0_modem_grp",
+        "gpt0_tmr0_grp", "gpt0_tmr1_grp", "gpt1_tmr0_grp", "gpt1_tmr1_grp",
+        "sdhci_grp", "cf_grp", "xd_grp", "touch_xy_grp",
+        "uart1_disable_i2c_grp", "uart1_disable_sd_grp", "uart2_3_grp",
+        "uart4_grp", "uart5_grp", "rs485_0_1_tdm_0_1_grp", "i2c_1_2_grp",
+        "i2c3_dis_smi_clcd_grp", "i2c3_dis_sd_i2s0_grp", "i2c_4_5_dis_smi_grp",
+        "i2c4_dis_sd_grp", "i2c5_dis_sd_grp", "i2c_6_7_dis_kbd_grp",
+        "i2c6_dis_sd_grp", "i2c7_dis_sd_grp", "can0_dis_nor_grp",
+        "can0_dis_sd_grp", "can1_dis_sd_grp", "can1_dis_kbd_grp", "pcie0_grp",
+        "pcie1_grp", "pcie2_grp", "sata0_grp", "sata1_grp", "sata2_grp",
+        "ssp1_dis_kbd_grp", "ssp1_dis_sd_grp", "gpt64_grp"
+
+For SPEAr1340 machines:
+        "pads_as_gpio_grp", "fsmc_8bit_grp", "fsmc_16bit_grp", "fsmc_pnor_grp",
+        "keyboard_row_col_grp", "keyboard_col5_grp", "spdif_in_grp",
+        "spdif_out_grp", "gpt_0_1_grp", "pwm0_grp", "pwm1_grp", "pwm2_grp",
+        "pwm3_grp", "vip_mux_grp", "vip_mux_cam0_grp", "vip_mux_cam1_grp",
+        "vip_mux_cam2_grp", "vip_mux_cam3_grp", "cam0_grp", "cam1_grp",
+        "cam2_grp", "cam3_grp", "smi_grp", "ssp0_grp", "ssp0_cs1_grp",
+        "ssp0_cs2_grp", "ssp0_cs3_grp", "uart0_grp", "uart0_enh_grp",
+        "uart1_grp", "i2s_in_grp", "i2s_out_grp", "gmii_grp", "rgmii_grp",
+        "rmii_grp", "sgmii_grp", "i2c0_grp", "i2c1_grp", "cec0_grp", "cec1_grp",
+        "sdhci_grp", "cf_grp", "xd_grp", "clcd_grp", "arm_trace_grp",
+        "miphy_dbg_grp", "pcie_grp", "sata_grp"
+
 Valid values for function names are:
 For All SPEAr3xx machines:
         "firda", "i2c0", "ssp_cs", "ssp0", "mii0", "gpio0", "uart0_ext",
@@ -106,3 +139,17 @@ For SPEAr320 machines:
         "uart2", "uart3", "uart4", "uart5", "uart6", "rs485", "touchscreen",
         "can0", "can1", "pwm0_1", "pwm2", "pwm3", "ssp1", "ssp2", "mii2",
         "mii0_1", "i2c1", "i2c2"
+
+
+For SPEAr1310 machines:
+        "i2c0", "ssp0", "i2s0", "i2s1", "clcd", "arm_gpio", "smi", "gmii",
+        "rgmii", "smii_0_1_2", "ras_mii_txclk", "nand", "keyboard", "uart0",
+        "gpt0", "gpt1", "sdhci", "cf", "xd", "touchscreen", "uart1", "uart2_3",
+        "uart4", "uart5", "rs485_0_1_tdm_0_1", "i2c_1_2", "i2c3_i2s1",
+        "i2c_4_5", "i2c_6_7", "can0", "can1", "pci", "sata", "ssp1", "gpt64"
+
+For SPEAr1340 machines:
+        "pads_as_gpio", "fsmc", "keyboard", "spdif_in", "spdif_out", "gpt_0_1",
+        "pwm", "vip", "cam0", "cam1", "cam2", "cam3", "smi", "ssp0", "uart0",
+        "uart1", "i2s", "gmac", "i2c0", "i2c1", "cec0", "cec1", "sdhci", "cf",
+        "xd", "clcd", "arm_trace", "miphy_dbg", "pcie", "sata"
diff --git a/Documentation/devicetree/bindings/rtc/lpc32xx-rtc.txt b/Documentation/devicetree/bindings/rtc/lpc32xx-rtc.txt
new file mode 100644
index 000000000000..a87a1e9bc060
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/lpc32xx-rtc.txt
@@ -0,0 +1,15 @@
+* NXP LPC32xx SoC Real Time Clock controller
+
+Required properties:
+- compatible: must be "nxp,lpc3220-rtc"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: The RTC interrupt
+
+Example:
+
+        rtc@40024000 {
+                compatible = "nxp,lpc3220-rtc";
+                reg = <0x40024000 0x1000>;
+                interrupts = <52 0>;
+        };
diff --git a/Documentation/devicetree/bindings/rtc/spear-rtc.txt b/Documentation/devicetree/bindings/rtc/spear-rtc.txt
new file mode 100644
index 000000000000..ca67ac62108e
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/spear-rtc.txt
@@ -0,0 +1,17 @@
+* SPEAr RTC
+
+Required properties:
+- compatible : "st,spear600-rtc"
+- reg : Address range of the rtc registers
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupt: Should contain the rtc interrupt number
+
+Example:
+
+        rtc@fc000000 {
+                compatible = "st,spear600-rtc";
+                reg = <0xfc000000 0x1000>;
+                interrupt-parent = <&vic1>;
+                interrupts = <12>;
+        };
diff --git a/Documentation/devicetree/bindings/sound/omap-dmic.txt b/Documentation/devicetree/bindings/sound/omap-dmic.txt
new file mode 100644
index 000000000000..fd8105f18978
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/omap-dmic.txt
@@ -0,0 +1,21 @@
+* Texas Instruments OMAP4+ Digital Microphone Module
+
+Required properties:
+- compatible: "ti,omap4-dmic"
+- reg: Register location and size as an array:
+       <MPU access base address, size>,
+       <L3 interconnect address, size>;
+- interrupts: Interrupt number for DMIC
+- interrupt-parent: The parent interrupt controller
+- ti,hwmods: Name of the hwmod associated with OMAP dmic IP
+
+Example:
+
+dmic: dmic@4012e000 {
+        compatible = "ti,omap4-dmic";
+        reg = <0x4012e000 0x7f>, /* MPU private access */
+              <0x4902e000 0x7f>; /* L3 Interconnect */
+        interrupts = <0 114 0x4>;
+        interrupt-parent = <&gic>;
+        ti,hwmods = "dmic";
+};
diff --git a/Documentation/devicetree/bindings/sound/omap-mcpdm.txt b/Documentation/devicetree/bindings/sound/omap-mcpdm.txt
new file mode 100644
index 000000000000..0741dff048dd
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/omap-mcpdm.txt
@@ -0,0 +1,21 @@
+* Texas Instruments OMAP4+ McPDM
+
+Required properties:
+- compatible: "ti,omap4-mcpdm"
+- reg: Register location and size as an array:
+       <MPU access base address, size>,
+       <L3 interconnect address, size>;
+- interrupts: Interrupt number for McPDM
+- interrupt-parent: The parent interrupt controller
+- ti,hwmods: Name of the hwmod associated to the McPDM
+
+Example:
+
+mcpdm: mcpdm@40132000 {
+        compatible = "ti,omap4-mcpdm";
+        reg = <0x40132000 0x7f>, /* MPU private access */
+              <0x49032000 0x7f>; /* L3 Interconnect */
+        interrupts = <0 112 0x4>;
+        interrupt-parent = <&gic>;
+        ti,hwmods = "mcpdm";
+};
diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt
index a9c0406280e8..b462d0c54823 100644
--- a/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt
+++ b/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt
@@ -11,7 +11,7 @@ Optional properties:
 
 Example:
 
-uart@73fbc000 {
+serial@73fbc000 {
         compatible = "fsl,imx51-uart", "fsl,imx21-uart";
         reg = <0x73fbc000 0x4000>;
         interrupts = <31>;
diff --git a/Documentation/devicetree/bindings/usb/tegra-usb.txt b/Documentation/devicetree/bindings/usb/tegra-usb.txt
index 007005ddbe12..e9b005dc7625 100644
--- a/Documentation/devicetree/bindings/usb/tegra-usb.txt
+++ b/Documentation/devicetree/bindings/usb/tegra-usb.txt
@@ -12,6 +12,9 @@ Required properties :
  - nvidia,vbus-gpio : If present, specifies a gpio that needs to be
    activated for the bus to be powered.
 
+Required properties for phy_type == ulpi:
+  - nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
+
 Optional properties:
   - dr_mode : dual role mode. Indicates the working mode for
    nvidia,tegra20-ehci compatible controllers.  Can be "host", "peripheral",