6 files changed, 253 insertions, 6 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt b/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt
new file mode 100644
index 000000000000..f93d51478d5a
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt
@@ -0,0 +1,38 @@
+Lantiq SoC External Bus memory mapped GPIO controller
+
+By attaching hardware latches to the EBU it is possible to create output
+only gpios. This driver configures a special memory address, which when
+written to outputs 16 bit to the latches.
+
+The node describing the memory mapped GPIOs needs to be a child of the node
+describing the "lantiq,localbus".
+
+Required properties:
+- compatible : Should be "lantiq,gpio-mm-lantiq"
+- reg : Address and length of the register set for the device
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- gpio-controller : Marks the device node as a gpio controller.
+
+Optional properties:
+- lantiq,shadow : The default value that we shall assume as already set on the
+  shift register cascade.
+
+Example:
+
+localbus@0 {
+        #address-cells = <2>;
+        #size-cells = <1>;
+        ranges = <0 0 0x0 0x3ffffff /* addrsel0 */
+                1 0 0x4000000 0x4000010>; /* addsel1 */
+        compatible = "lantiq,localbus", "simple-bus";
+
+        gpio_mm0: gpio@4000000 {
+                compatible = "lantiq,gpio-mm";
+                reg = <1 0x0 0x10>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                lantiq,shadow = <0x77f>
+        };
+}
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mxs.txt b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt
new file mode 100644
index 000000000000..0c35673f7a3e
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt
@@ -0,0 +1,87 @@
+* Freescale MXS GPIO controller
+
+The Freescale MXS GPIO controller is part of MXS PIN controller.  The
+GPIOs are organized in port/bank.  Each port consists of 32 GPIOs.
+
+As the GPIO controller is embedded in the PIN controller and all the
+GPIO ports share the same IO space with PIN controller, the GPIO node
+will be represented as sub-nodes of MXS pinctrl node.
+
+Required properties for GPIO node:
+- compatible : Should be "fsl,<soc>-gpio".  The supported SoCs include
+  imx23 and imx28.
+- interrupts : Should be the port interrupt shared by all 32 pins.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells : Should be 2.  The first cell is the GPIO number.
+  The second cell bits[3:0] is used to specify trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+
+Note: Each GPIO port should have an alias correctly numbered in "aliases"
+node.
+
+Examples:
+
+aliases {
+        gpio0 = &gpio0;
+        gpio1 = &gpio1;
+        gpio2 = &gpio2;
+        gpio3 = &gpio3;
+        gpio4 = &gpio4;
+};
+
+pinctrl@80018000 {
+        compatible = "fsl,imx28-pinctrl", "simple-bus";
+        reg = <0x80018000 2000>;
+
+        gpio0: gpio@0 {
+                compatible = "fsl,imx28-gpio";
+                interrupts = <127>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+        };
+
+        gpio1: gpio@1 {
+                compatible = "fsl,imx28-gpio";
+                interrupts = <126>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+        };
+
+        gpio2: gpio@2 {
+                compatible = "fsl,imx28-gpio";
+                interrupts = <125>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+        };
+
+        gpio3: gpio@3 {
+                compatible = "fsl,imx28-gpio";
+                interrupts = <124>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+        };
+
+        gpio4: gpio@4 {
+                compatible = "fsl,imx28-gpio";
+                interrupts = <123>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+        };
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt
new file mode 100644
index 000000000000..ee87467ad8d6
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt
@@ -0,0 +1,31 @@
+Nomadik GPIO controller
+
+Required properties:
+- compatible            : Should be "st,nomadik-gpio".
+- reg                   : Physical base address and length of the controller's registers.
+- interrupts            : The interrupt outputs from the controller.
+- #gpio-cells           : Should be two:
+                            The first cell is the pin number.
+                            The second cell is used to specify optional parameters:
+                              - bits[3:0] trigger type and level flags:
+                                  1 = low-to-high edge triggered.
+                                  2 = high-to-low edge triggered.
+                                  4 = active high level-sensitive.
+                                  8 = active low level-sensitive.
+- gpio-controller       : Marks the device node as a GPIO controller.
+- interrupt-controller  : Marks the device node as an interrupt controller.
+- gpio-bank             : Specifies which bank a controller owns.
+- st,supports-sleepmode : Specifies whether controller can sleep or not
+
+Example:
+
+                gpio1: gpio@8012e080 {
+                        compatible = "st,nomadik-gpio";
+                        reg =  <0x8012e080 0x80>;
+                        interrupts = <0 120 0x4>;
+                        #gpio-cells = <2>;
+                        gpio-controller;
+                        interrupt-controller;
+                        supports-sleepmode;
+                        gpio-bank = <1>;
+                };
diff --git a/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt
new file mode 100644
index 000000000000..854de130a971
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt
@@ -0,0 +1,42 @@
+Lantiq SoC Serial To Parallel (STP) GPIO controller
+
+The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a
+peripheral controller used to drive external shift register cascades. At most
+3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem
+to drive the 2 LSBs of the cascade automatically.
+
+
+Required properties:
+- compatible : Should be "lantiq,gpio-stp-xway"
+- reg : Address and length of the register set for the device
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- gpio-controller : Marks the device node as a gpio controller.
+
+Optional properties:
+- lantiq,shadow : The default value that we shall assume as already set on the
+  shift register cascade.
+- lantiq,groups : Set the 3 bit mask to select which of the 3 groups are enabled
+  in the shift register cascade.
+- lantiq,dsl : The dsl core can control the 2 LSBs of the gpio cascade. This 2 bit
+  property can enable this feature.
+- lantiq,phy1 : The gphy1 core can control 3 bits of the gpio cascade.
+- lantiq,phy2 : The gphy2 core can control 3 bits of the gpio cascade.
+- lantiq,rising : use rising instead of falling edge for the shift register
+
+Example:
+
+gpio1: stp@E100BB0 {
+        compatible = "lantiq,gpio-stp-xway";
+        reg = <0xE100BB0 0x40>;
+        #gpio-cells = <2>;
+        gpio-controller;
+
+        lantiq,shadow = <0xffff>;
+        lantiq,groups = <0x7>;
+        lantiq,dsl = <0x3>;
+        lantiq,phy1 = <0x7>;
+        lantiq,phy2 = <0x7>;
+        /* lantiq,rising; */
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt b/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt
new file mode 100644
index 000000000000..49819367a011
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt
@@ -0,0 +1,43 @@
+NXP LPC32xx SoC GPIO controller
+
+Required properties:
+- compatible: must be "nxp,lpc3220-gpio"
+- reg: Physical base address and length of the controller's registers.
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells: Should be 3:
+   1) bank:
+      0: GPIO P0
+      1: GPIO P1
+      2: GPIO P2
+      3: GPIO P3
+      4: GPI P3
+      5: GPO P3
+   2) pin number
+   3) optional parameters:
+      - bit 0 specifies polarity (0 for normal, 1 for inverted)
+- reg: Index of the GPIO group
+
+Example:
+
+        gpio: gpio@40028000 {
+                compatible = "nxp,lpc3220-gpio";
+                reg = <0x40028000 0x1000>;
+                gpio-controller;
+                #gpio-cells = <3>; /* bank, pin, flags */
+        };
+
+        leds {
+                compatible = "gpio-leds";
+
+                led0 {
+                        gpios = <&gpio 5 1 1>; /* GPO_P3 1, active low */
+                        linux,default-trigger = "heartbeat";
+                        default-state = "off";
+                };
+
+                led1 {
+                        gpios = <&gpio 5 14 1>; /* GPO_P3 14, active low */
+                        linux,default-trigger = "timer";
+                        default-state = "off";
+                };
+        };
diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt
index 1e34cfe5ebea..05428f39d9ac 100644
--- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt
@@ -3,19 +3,25 @@
 Required properties:
 - compatible : Should be "mrvl,pxa-gpio" or "mrvl,mmp-gpio"
 - reg : Address and length of the register set for the device
-- interrupts : Should be the port interrupt shared by all gpio pins, if
-- interrupt-name : Should be the name of irq resource.
-  one number.
+- interrupts : Should be the port interrupt shared by all gpio pins.
+  There're three gpio interrupts in arch-pxa, and they're gpio0,
+  gpio1 and gpio_mux. There're only one gpio interrupt in arch-mmp,
+  gpio_mux.
+- interrupt-name : Should be the name of irq resource. Each interrupt
+  binds its interrupt-name.
+- interrupt-controller : Identifies the node as an interrupt controller.
+- #interrupt-cells: Specifies the number of cells needed to encode an
+  interrupt source.
 - gpio-controller : Marks the device node as a gpio controller.
 - #gpio-cells : Should be one.  It is the pin number.
 
 Example:
 
         gpio: gpio@d4019000 {
-                compatible = "mrvl,mmp-gpio", "mrvl,pxa-gpio";
+                compatible = "mrvl,mmp-gpio";
                 reg = <0xd4019000 0x1000>;
-                interrupts = <49>, <17>, <18>;
-                interrupt-name = "gpio_mux", "gpio0", "gpio1";
+                interrupts = <49>;
+                interrupt-name = "gpio_mux";
                 gpio-controller;
                 #gpio-cells = <1>;
                 interrupt-controller;