1 files changed, 84 insertions, 51 deletions

diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index e6d2b840e870..ae6d573574cd 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -34,7 +34,7 @@
 #include <linux/dmi.h>
 
 #define DRV_NAME "pata_ali"
-#define DRV_VERSION "0.6.6"
+#define DRV_VERSION "0.7.1"
 
 /*
  *      Cable special cases
@@ -348,6 +348,8 @@ static struct scsi_host_template ali_sht = {
         .slave_configure        = ata_scsi_slave_config,
         .slave_destroy          = ata_scsi_slave_destroy,
         .bios_param             = ata_std_bios_param,
+        .resume                 = ata_scsi_device_resume,
+        .suspend                = ata_scsi_device_suspend,
 };
 
 /*
@@ -497,6 +499,69 @@ static struct ata_port_operations ali_c5_port_ops = {
         .host_stop      = ata_host_stop
 };
 
+
+/**
+ *      ali_init_chipset        -       chip setup function
+ *      @pdev: PCI device of ATA controller
+ *
+ *      Perform the setup on the device that must be done both at boot
+ *      and at resume time.
+ */
+ 
+static void ali_init_chipset(struct pci_dev *pdev)
+{
+        u8 rev, tmp;
+        struct pci_dev *north, *isa_bridge;
+
+        pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
+
+        /*
+         * The chipset revision selects the driver operations and
+         * mode data.
+         */
+
+        if (rev >= 0x20 && rev < 0xC2) {
+                /* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */
+                pci_read_config_byte(pdev, 0x4B, &tmp);
+                /* Clear CD-ROM DMA write bit */
+                tmp &= 0x7F;
+                pci_write_config_byte(pdev, 0x4B, tmp);
+        } else if (rev >= 0xC2) {
+                /* Enable cable detection logic */
+                pci_read_config_byte(pdev, 0x4B, &tmp);
+                pci_write_config_byte(pdev, 0x4B, tmp | 0x08);
+        }
+        north = pci_get_slot(pdev->bus, PCI_DEVFN(0,0));
+        isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
+
+        if (north && north->vendor == PCI_VENDOR_ID_AL && isa_bridge) {
+                /* Configure the ALi bridge logic. For non ALi rely on BIOS.
+                   Set the south bridge enable bit */
+                pci_read_config_byte(isa_bridge, 0x79, &tmp);
+                if (rev == 0xC2)
+                        pci_write_config_byte(isa_bridge, 0x79, tmp | 0x04);
+                else if (rev > 0xC2)
+                        pci_write_config_byte(isa_bridge, 0x79, tmp | 0x02);
+        }
+        if (rev >= 0x20) {
+                /*
+                 * CD_ROM DMA on (0x53 bit 0). Enable this even if we want
+                 * to use PIO. 0x53 bit 1 (rev 20 only) - enable FIFO control
+                 * via 0x54/55.
+                 */
+                pci_read_config_byte(pdev, 0x53, &tmp);
+                if (rev <= 0x20)
+                        tmp &= ~0x02;
+                if (rev >= 0xc7)
+                        tmp |= 0x03;
+                else
+                        tmp |= 0x01;    /* CD_ROM enable for DMA */
+                pci_write_config_byte(pdev, 0x53, tmp);
+        }
+        pci_dev_put(isa_bridge);
+        pci_dev_put(north);
+        ata_pci_clear_simplex(pdev);
+}
 /**
  *      ali_init_one            -       discovery callback
  *      @pdev: PCI device ID
@@ -570,7 +635,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 
         static struct ata_port_info *port_info[2];
         u8 rev, tmp;
-        struct pci_dev *north, *isa_bridge;
+        struct pci_dev *isa_bridge;
 
         pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
 
@@ -582,11 +647,6 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
         if (rev < 0x20) {
                 port_info[0] = port_info[1] = &info_early;
         } else if (rev < 0xC2) {
-                /* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */
-                pci_read_config_byte(pdev, 0x4B, &tmp);
-                /* Clear CD-ROM DMA write bit */
-                tmp &= 0x7F;
-                pci_write_config_byte(pdev, 0x4B, tmp);
                 port_info[0] = port_info[1] = &info_20;
         } else if (rev == 0xC2) {
                 port_info[0] = port_info[1] = &info_c2;
@@ -597,54 +657,25 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
         } else
                 port_info[0] = port_info[1] = &info_c5;
 
-        if (rev >= 0xC2) {
-                /* Enable cable detection logic */
-                pci_read_config_byte(pdev, 0x4B, &tmp);
-                pci_write_config_byte(pdev, 0x4B, tmp | 0x08);
-        }
-
-        north = pci_get_slot(pdev->bus, PCI_DEVFN(0,0));
+        ali_init_chipset(pdev);
+        
         isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
-
-        if (north && north->vendor == PCI_VENDOR_ID_AL) {
-                /* Configure the ALi bridge logic. For non ALi rely on BIOS.
-                   Set the south bridge enable bit */
-                pci_read_config_byte(isa_bridge, 0x79, &tmp);
-                if (rev == 0xC2)
-                        pci_write_config_byte(isa_bridge, 0x79, tmp | 0x04);
-                else if (rev > 0xC2)
-                        pci_write_config_byte(isa_bridge, 0x79, tmp | 0x02);
+        if (isa_bridge && rev >= 0x20 && rev < 0xC2) {
+                /* Are we paired with a UDMA capable chip */
+                pci_read_config_byte(isa_bridge, 0x5E, &tmp);
+                if ((tmp & 0x1E) == 0x12)
+                        port_info[0] = port_info[1] = &info_20_udma;
+                pci_dev_put(isa_bridge);
         }
-
-        if (rev >= 0x20) {
-                if (rev < 0xC2) {
-                        /* Are we paired with a UDMA capable chip */
-                        pci_read_config_byte(isa_bridge, 0x5E, &tmp);
-                        if ((tmp & 0x1E) == 0x12)
-                                port_info[0] = port_info[1] = &info_20_udma;
-                }
-                /*
-                 * CD_ROM DMA on (0x53 bit 0). Enable this even if we want
-                 * to use PIO. 0x53 bit 1 (rev 20 only) - enable FIFO control
-                 * via 0x54/55.
-                 */
-                pci_read_config_byte(pdev, 0x53, &tmp);
-                if (rev <= 0x20)
-                        tmp &= ~0x02;
-                if (rev >= 0xc7)
-                        tmp |= 0x03;
-                else
-                        tmp |= 0x01;    /* CD_ROM enable for DMA */
-                pci_write_config_byte(pdev, 0x53, tmp);
-        }
-
-        pci_dev_put(isa_bridge);
-        pci_dev_put(north);
-
-        ata_pci_clear_simplex(pdev);
         return ata_pci_init_one(pdev, port_info, 2);
 }
 
+static int ali_reinit_one(struct pci_dev *pdev)
+{
+        ali_init_chipset(pdev);
+        return ata_pci_device_resume(pdev);
+}
+
 static const struct pci_device_id ali[] = {
         { PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5228), },
         { PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5229), },
@@ -656,7 +687,9 @@ static struct pci_driver ali_pci_driver = {
         .name           = DRV_NAME,
         .id_table       = ali,
         .probe          = ali_init_one,
-        .remove         = ata_pci_remove_one
+        .remove         = ata_pci_remove_one,
+        .suspend        = ata_pci_device_suspend,
+        .resume         = ali_reinit_one,
 };
 
 static int __init ali_init(void)