aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
Diffstat
-rw-r--r--arch/arm/configs/at91sam9263_defconfig1
-rw-r--r--arch/arm/mach-at91/Kconfig6
-rw-r--r--arch/arm/mach-at91/Makefile1
-rw-r--r--arch/arm/mach-at91/board-neocore926.c387
4 files changed, 0 insertions, 395 deletions
diff --git a/arch/arm/configs/at91sam9263_defconfig b/arch/arm/configs/at91sam9263_defconfig
index c5212f43eee6..36fed66bd4b5 100644
--- a/arch/arm/configs/at91sam9263_defconfig
+++ b/arch/arm/configs/at91sam9263_defconfig
@@ -18,7 +18,6 @@ CONFIG_ARCH_AT91=y
18CONFIG_ARCH_AT91SAM9263=y 18CONFIG_ARCH_AT91SAM9263=y
19CONFIG_MACH_AT91SAM9263EK=y 19CONFIG_MACH_AT91SAM9263EK=y
20CONFIG_MACH_USB_A9263=y 20CONFIG_MACH_USB_A9263=y
21CONFIG_MACH_NEOCORE926=y
22CONFIG_MTD_AT91_DATAFLASH_CARD=y 21CONFIG_MTD_AT91_DATAFLASH_CARD=y
23# CONFIG_ARM_THUMB is not set 22# CONFIG_ARM_THUMB is not set
24CONFIG_AEABI=y 23CONFIG_AEABI=y
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 958358c91afd..6071f4c3d654 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -352,12 +352,6 @@ config MACH_USB_A9263
352 Select this if you are using a Calao Systems USB-A9263. 352 Select this if you are using a Calao Systems USB-A9263.
353 <http://www.calao-systems.com> 353 <http://www.calao-systems.com>
354 354
355config MACH_NEOCORE926
356 bool "Adeneo NEOCORE926"
357 select HAVE_AT91_DATAFLASH_CARD
358 help
359 Select this if you are using the Adeneo Neocore 926 board.
360
361endif 355endif
362 356
363# ---------------------------------------------------------- 357# ----------------------------------------------------------
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index b38a1dcb79b8..39218ca6d8e8 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -66,7 +66,6 @@ obj-$(CONFIG_MACH_AT91SAM9G10EK) += board-sam9261ek.o
66# AT91SAM9263 board-specific support 66# AT91SAM9263 board-specific support
67obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o 67obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o
68obj-$(CONFIG_MACH_USB_A9263) += board-usb-a926x.o 68obj-$(CONFIG_MACH_USB_A9263) += board-usb-a926x.o
69obj-$(CONFIG_MACH_NEOCORE926) += board-neocore926.o
70 69
71# AT91SAM9RL board-specific support 70# AT91SAM9RL board-specific support
72obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o 71obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o
diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c
deleted file mode 100644
index 5b4760fe53de..000000000000
--- a/arch/arm/mach-at91/board-neocore926.c
+++ /dev/null
@@ -1,387 +0,0 @@
1/*
2 * linux/arch/arm/mach-at91/board-neocore926.c
3 *
4 * Copyright (C) 2005 SAN People
5 * Copyright (C) 2007 Atmel Corporation
6 * Copyright (C) 2008 ADENEO.
7 *
8 * This program is free software; you can redistribute it and/or modify
9 * it under the terms of the GNU General Public License as published by
10 * the Free Software Foundation; either version 2 of the License, or
11 * (at your option) any later version.
12 *
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
17 *
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software
20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
21 */
22
23#include <linux/types.h>
24#include <linux/gpio.h>
25#include <linux/init.h>
26#include <linux/mm.h>
27#include <linux/module.h>
28#include <linux/platform_device.h>
29#include <linux/spi/spi.h>
30#include <linux/spi/ads7846.h>
31#include <linux/fb.h>
32#include <linux/gpio_keys.h>
33#include <linux/input.h>
34
35#include <video/atmel_lcdc.h>
36
37#include <asm/setup.h>
38#include <asm/mach-types.h>
39#include <asm/irq.h>
40#include <asm/sizes.h>
41
42#include <asm/mach/arch.h>
43#include <asm/mach/map.h>
44#include <asm/mach/irq.h>
45
46#include <mach/hardware.h>
47#include <mach/at91sam9_smc.h>
48
49#include "at91_aic.h"
50#include "board.h"
51#include "sam9_smc.h"
52#include "generic.h"
53
54
55static void __init neocore926_init_early(void)
56{
57 /* Initialize processor: 20 MHz crystal */
58 at91_initialize(20000000);
59}
60
61/*
62 * USB Host port
63 */
64static struct at91_usbh_data __initdata neocore926_usbh_data = {
65 .ports = 2,
66 .vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 },
67 .overcurrent_pin= {-EINVAL, -EINVAL},
68};
69
70/*
71 * USB Device port
72 */
73static struct at91_udc_data __initdata neocore926_udc_data = {
74 .vbus_pin = AT91_PIN_PA25,
75 .pullup_pin = -EINVAL, /* pull-up driven by UDC */
76};
77
78
79/*
80 * ADS7846 Touchscreen
81 */
82#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
83static int ads7843_pendown_state(void)
84{
85 return !at91_get_gpio_value(AT91_PIN_PA15); /* Touchscreen PENIRQ */
86}
87
88static struct ads7846_platform_data ads_info = {
89 .model = 7843,
90 .x_min = 150,
91 .x_max = 3830,
92 .y_min = 190,
93 .y_max = 3830,
94 .vref_delay_usecs = 100,
95 .x_plate_ohms = 450,
96 .y_plate_ohms = 250,
97 .pressure_max = 15000,
98 .debounce_max = 1,
99 .debounce_rep = 0,
100 .debounce_tol = (~0),
101 .get_pendown_state = ads7843_pendown_state,
102};
103
104static void __init neocore926_add_device_ts(void)
105{
106 at91_set_B_periph(AT91_PIN_PA15, 1); /* External IRQ1, with pullup */
107 at91_set_gpio_input(AT91_PIN_PC13, 1); /* Touchscreen BUSY signal */
108}
109#else
110static void __init neocore926_add_device_ts(void) {}
111#endif
112
113/*
114 * SPI devices.
115 */
116static struct spi_board_info neocore926_spi_devices[] = {
117#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
118 { /* DataFlash card */
119 .modalias = "mtd_dataflash",
120 .chip_select = 0,
121 .max_speed_hz = 15 * 1000 * 1000,
122 .bus_num = 0,
123 },
124#endif
125#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
126 {
127 .modalias = "ads7846",
128 .chip_select = 1,
129 .max_speed_hz = 125000 * 16,
130 .bus_num = 0,
131 .platform_data = &ads_info,
132 .irq = NR_IRQS_LEGACY + AT91SAM9263_ID_IRQ1,
133 },
134#endif
135};
136
137
138/*
139 * MCI (SD/MMC)
140 */
141static struct mci_platform_data __initdata neocore926_mci0_data = {
142 .slot[0] = {
143 .bus_width = 4,
144 .detect_pin = AT91_PIN_PE18,
145 .wp_pin = AT91_PIN_PE19,
146 },
147};
148
149
150/*
151 * MACB Ethernet device
152 */
153static struct macb_platform_data __initdata neocore926_macb_data = {
154 .phy_irq_pin = AT91_PIN_PE31,
155 .is_rmii = 1,
156};
157
158
159/*
160 * NAND flash
161 */
162static struct mtd_partition __initdata neocore926_nand_partition[] = {
163 {
164 .name = "Linux Kernel", /* "Partition 1", */
165 .offset = 0,
166 .size = SZ_8M,
167 },
168 {
169 .name = "Filesystem", /* "Partition 2", */
170 .offset = MTDPART_OFS_NXTBLK,
171 .size = SZ_32M,
172 },
173 {
174 .name = "Free", /* "Partition 3", */
175 .offset = MTDPART_OFS_NXTBLK,
176 .size = MTDPART_SIZ_FULL,
177 },
178};
179
180static struct atmel_nand_data __initdata neocore926_nand_data = {
181 .ale = 21,
182 .cle = 22,
183 .rdy_pin = AT91_PIN_PB19,
184 .rdy_pin_active_low = 1,
185 .enable_pin = AT91_PIN_PD15,
186 .ecc_mode = NAND_ECC_SOFT,
187 .parts = neocore926_nand_partition,
188 .num_parts = ARRAY_SIZE(neocore926_nand_partition),
189 .det_pin = -EINVAL,
190};
191
192static struct sam9_smc_config __initdata neocore926_nand_smc_config = {
193 .ncs_read_setup = 0,
194 .nrd_setup = 1,
195 .ncs_write_setup = 0,
196 .nwe_setup = 1,
197
198 .ncs_read_pulse = 4,
199 .nrd_pulse = 4,
200 .ncs_write_pulse = 4,
201 .nwe_pulse = 4,
202
203 .read_cycle = 6,
204 .write_cycle = 6,
205
206 .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
207 .tdf_cycles = 2,
208};
209
210static void __init neocore926_add_device_nand(void)
211{
212 /* configure chip-select 3 (NAND) */
213 sam9_smc_configure(0, 3, &neocore926_nand_smc_config);
214
215 at91_add_device_nand(&neocore926_nand_data);
216}
217
218
219/*
220 * LCD Controller
221 */
222#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
223static struct fb_videomode at91_tft_vga_modes[] = {
224 {
225 .name = "TX09D50VM1CCA @ 60",
226 .refresh = 60,
227 .xres = 240, .yres = 320,
228 .pixclock = KHZ2PICOS(5000),
229
230 .left_margin = 1, .right_margin = 33,
231 .upper_margin = 1, .lower_margin = 0,
232 .hsync_len = 5, .vsync_len = 1,
233
234 .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
235 .vmode = FB_VMODE_NONINTERLACED,
236 },
237};
238
239static struct fb_monspecs at91fb_default_monspecs = {
240 .manufacturer = "HIT",
241 .monitor = "TX09D70VM1CCA",
242
243 .modedb = at91_tft_vga_modes,
244 .modedb_len = ARRAY_SIZE(at91_tft_vga_modes),
245 .hfmin = 15000,
246 .hfmax = 64000,
247 .vfmin = 50,
248 .vfmax = 150,
249};
250
251#define AT91SAM9263_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
252 | ATMEL_LCDC_DISTYPE_TFT \
253 | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
254
255static void at91_lcdc_power_control(int on)
256{
257 at91_set_gpio_value(AT91_PIN_PA30, on);
258}
259
260/* Driver datas */
261static struct atmel_lcdfb_info __initdata neocore926_lcdc_data = {
262 .lcdcon_is_backlight = true,
263 .default_bpp = 16,
264 .default_dmacon = ATMEL_LCDC_DMAEN,
265 .default_lcdcon2 = AT91SAM9263_DEFAULT_LCDCON2,
266 .default_monspecs = &at91fb_default_monspecs,
267 .atmel_lcdfb_power_control = at91_lcdc_power_control,
268 .guard_time = 1,
269 .lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB555,
270};
271
272#else
273static struct atmel_lcdfb_info __initdata neocore926_lcdc_data;
274#endif
275
276
277/*
278 * GPIO Buttons
279 */
280#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
281static struct gpio_keys_button neocore926_buttons[] = {
282 { /* BP1, "leftclic" */
283 .code = BTN_LEFT,
284 .gpio = AT91_PIN_PC5,
285 .active_low = 1,
286 .desc = "left_click",
287 .wakeup = 1,
288 },
289 { /* BP2, "rightclic" */
290 .code = BTN_RIGHT,
291 .gpio = AT91_PIN_PC4,
292 .active_low = 1,
293 .desc = "right_click",
294 .wakeup = 1,
295 },
296};
297
298static struct gpio_keys_platform_data neocore926_button_data = {
299 .buttons = neocore926_buttons,
300 .nbuttons = ARRAY_SIZE(neocore926_buttons),
301};
302
303static struct platform_device neocore926_button_device = {
304 .name = "gpio-keys",
305 .id = -1,
306 .num_resources = 0,
307 .dev = {
308 .platform_data = &neocore926_button_data,
309 }
310};
311
312static void __init neocore926_add_device_buttons(void)
313{
314 at91_set_GPIO_periph(AT91_PIN_PC5, 0); /* left button */
315 at91_set_deglitch(AT91_PIN_PC5, 1);
316 at91_set_GPIO_periph(AT91_PIN_PC4, 0); /* right button */
317 at91_set_deglitch(AT91_PIN_PC4, 1);
318
319 platform_device_register(&neocore926_button_device);
320}
321#else
322static void __init neocore926_add_device_buttons(void) {}
323#endif
324
325
326/*
327 * AC97
328 */
329static struct ac97c_platform_data neocore926_ac97_data = {
330 .reset_pin = AT91_PIN_PA13,
331};
332
333
334static void __init neocore926_board_init(void)
335{
336 /* Serial */
337 /* DBGU on ttyS0. (Rx & Tx only) */
338 at91_register_uart(0, 0, 0);
339
340 /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
341 at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
342 at91_add_device_serial();
343
344 /* USB Host */
345 at91_add_device_usbh(&neocore926_usbh_data);
346
347 /* USB Device */
348 at91_add_device_udc(&neocore926_udc_data);
349
350 /* SPI */
351 at91_set_gpio_output(AT91_PIN_PE20, 1); /* select spi0 clock */
352 at91_add_device_spi(neocore926_spi_devices, ARRAY_SIZE(neocore926_spi_devices));
353
354 /* Touchscreen */
355 neocore926_add_device_ts();
356
357 /* MMC */
358 at91_add_device_mci(0, &neocore926_mci0_data);
359
360 /* Ethernet */
361 at91_add_device_eth(&neocore926_macb_data);
362
363 /* NAND */
364 neocore926_add_device_nand();
365
366 /* I2C */
367 at91_add_device_i2c(NULL, 0);
368
369 /* LCD Controller */
370 at91_add_device_lcdc(&neocore926_lcdc_data);
371
372 /* Push Buttons */
373 neocore926_add_device_buttons();
374
375 /* AC97 */
376 at91_add_device_ac97(&neocore926_ac97_data);
377}
378
379MACHINE_START(NEOCORE926, "ADENEO NEOCORE 926")
380 /* Maintainer: ADENEO */
381 .init_time = at91sam926x_pit_init,
382 .map_io = at91_map_io,
383 .handle_irq = at91_aic_handle_irq,
384 .init_early = neocore926_init_early,
385 .init_irq = at91_init_irq_default,
386 .init_machine = neocore926_board_init,
387MACHINE_END
generated by cgit v1.2.2 (git 2.25.0) at 2026-04-04 12:47:15 -0400