11 files changed, 104 insertions, 56 deletions

diff --git a/drivers/pci/pci-driver.c b/drivers/pci/pci-driver.c
index bf0cee629b60..099f46cd8e87 100644
--- a/drivers/pci/pci-driver.c
+++ b/drivers/pci/pci-driver.c
@@ -748,6 +748,18 @@ static int pci_pm_suspend_noirq(struct device *dev)
 
         pci_pm_set_unknown_state(pci_dev);
 
+        /*
+         * Some BIOSes from ASUS have a bug: If a USB EHCI host controller's
+         * PCI COMMAND register isn't 0, the BIOS assumes that the controller
+         * hasn't been quiesced and tries to turn it off.  If the controller
+         * is already in D3, this can hang or cause memory corruption.
+         *
+         * Since the value of the COMMAND register doesn't matter once the
+         * device has been suspended, we can safely set it to 0 here.
+         */
+        if (pci_dev->class == PCI_CLASS_SERIAL_USB_EHCI)
+                pci_write_config_word(pci_dev, PCI_COMMAND, 0);
+
         return 0;
 }
 
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index 77cb54a65cde..447e83472c01 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -1744,11 +1744,6 @@ int pci_prepare_to_sleep(struct pci_dev *dev)
         if (target_state == PCI_POWER_ERROR)
                 return -EIO;
 
-        /* Some devices mustn't be in D3 during system sleep */
-        if (target_state == PCI_D3hot &&
-                        (dev->dev_flags & PCI_DEV_FLAGS_NO_D3_DURING_SLEEP))
-                return 0;
-
         pci_enable_wake(dev, target_state, device_may_wakeup(&dev->dev));
 
         error = pci_set_power_state(dev, target_state);
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index 194b243a2817..2a7521677541 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -2929,32 +2929,6 @@ static void __devinit disable_igfx_irq(struct pci_dev *dev)
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0102, disable_igfx_irq);
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x010a, disable_igfx_irq);
 
-/*
- * The Intel 6 Series/C200 Series chipset's EHCI controllers on many
- * ASUS motherboards will cause memory corruption or a system crash
- * if they are in D3 while the system is put into S3 sleep.
- */
-static void __devinit asus_ehci_no_d3(struct pci_dev *dev)
-{
-        const char *sys_info;
-        static const char good_Asus_board[] = "P8Z68-V";
-
-        if (dev->dev_flags & PCI_DEV_FLAGS_NO_D3_DURING_SLEEP)
-                return;
-        if (dev->subsystem_vendor != PCI_VENDOR_ID_ASUSTEK)
-                return;
-        sys_info = dmi_get_system_info(DMI_BOARD_NAME);
-        if (sys_info && memcmp(sys_info, good_Asus_board,
-                        sizeof(good_Asus_board) - 1) == 0)
-                return;
-
-        dev_info(&dev->dev, "broken D3 during system sleep on ASUS\n");
-        dev->dev_flags |= PCI_DEV_FLAGS_NO_D3_DURING_SLEEP;
-        device_set_wakeup_capable(&dev->dev, false);
-}
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1c26, asus_ehci_no_d3);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1c2d, asus_ehci_no_d3);
-
 static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f,
                           struct pci_fixup *end)
 {
diff --git a/drivers/usb/class/cdc-wdm.c b/drivers/usb/class/cdc-wdm.c
index 8fd398dffced..ee469274a3fe 100644
--- a/drivers/usb/class/cdc-wdm.c
+++ b/drivers/usb/class/cdc-wdm.c
@@ -500,6 +500,8 @@ retry:
                         goto retry;
                 }
                 if (!desc->reslength) { /* zero length read */
+                        dev_dbg(&desc->intf->dev, "%s: zero length - clearing WDM_READ\n", __func__);
+                        clear_bit(WDM_READ, &desc->flags);
                         spin_unlock_irq(&desc->iuspin);
                         goto retry;
                 }
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 25a7422ee657..8fb484984c86 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -2324,12 +2324,16 @@ static unsigned hub_is_wusb(struct usb_hub *hub)
 static int hub_port_reset(struct usb_hub *hub, int port1,
                         struct usb_device *udev, unsigned int delay, bool warm);
 
-/* Is a USB 3.0 port in the Inactive state? */
-static bool hub_port_inactive(struct usb_hub *hub, u16 portstatus)
+/* Is a USB 3.0 port in the Inactive or Complinance Mode state?
+ * Port worm reset is required to recover
+ */
+static bool hub_port_warm_reset_required(struct usb_hub *hub, u16 portstatus)
 {
         return hub_is_superspeed(hub->hdev) &&
-                (portstatus & USB_PORT_STAT_LINK_STATE) ==
-                USB_SS_PORT_LS_SS_INACTIVE;
+                (((portstatus & USB_PORT_STAT_LINK_STATE) ==
+                  USB_SS_PORT_LS_SS_INACTIVE) ||
+                 ((portstatus & USB_PORT_STAT_LINK_STATE) ==
+                  USB_SS_PORT_LS_COMP_MOD)) ;
 }
 
 static int hub_port_wait_reset(struct usb_hub *hub, int port1,
@@ -2365,7 +2369,7 @@ static int hub_port_wait_reset(struct usb_hub *hub, int port1,
                          *
                          * See https://bugzilla.kernel.org/show_bug.cgi?id=41752
                          */
-                        if (hub_port_inactive(hub, portstatus)) {
+                        if (hub_port_warm_reset_required(hub, portstatus)) {
                                 int ret;
 
                                 if ((portchange & USB_PORT_STAT_C_CONNECTION))
@@ -4408,9 +4412,7 @@ static void hub_events(void)
                         /* Warm reset a USB3 protocol port if it's in
                          * SS.Inactive state.
                          */
-                        if (hub_is_superspeed(hub->hdev) &&
-                                (portstatus & USB_PORT_STAT_LINK_STATE)
-                                        == USB_SS_PORT_LS_SS_INACTIVE) {
+                        if (hub_port_warm_reset_required(hub, portstatus)) {
                                 dev_dbg(hub_dev, "warm reset port %d\n", i);
                                 hub_port_reset(hub, i, NULL,
                                                 HUB_BH_RESET_TIME, true);
diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index 2732ef660c5c..7b01094d7993 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -462,6 +462,42 @@ void xhci_test_and_clear_bit(struct xhci_hcd *xhci, __le32 __iomem **port_array,
         }
 }
 
+/* Updates Link Status for super Speed port */
+static void xhci_hub_report_link_state(u32 *status, u32 status_reg)
+{
+        u32 pls = status_reg & PORT_PLS_MASK;
+
+        /* resume state is a xHCI internal state.
+         * Do not report it to usb core.
+         */
+        if (pls == XDEV_RESUME)
+                return;
+
+        /* When the CAS bit is set then warm reset
+         * should be performed on port
+         */
+        if (status_reg & PORT_CAS) {
+                /* The CAS bit can be set while the port is
+                 * in any link state.
+                 * Only roothubs have CAS bit, so we
+                 * pretend to be in compliance mode
+                 * unless we're already in compliance
+                 * or the inactive state.
+                 */
+                if (pls != USB_SS_PORT_LS_COMP_MOD &&
+                    pls != USB_SS_PORT_LS_SS_INACTIVE) {
+                        pls = USB_SS_PORT_LS_COMP_MOD;
+                }
+                /* Return also connection bit -
+                 * hub state machine resets port
+                 * when this bit is set.
+                 */
+                pls |= USB_PORT_STAT_CONNECTION;
+        }
+        /* update status field */
+        *status |= pls;
+}
+
 int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
                 u16 wIndex, char *buf, u16 wLength)
 {
@@ -606,13 +642,9 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
                         else
                                 status |= USB_PORT_STAT_POWER;
                 }
-                /* Port Link State */
+                /* Update Port Link State for super speed ports*/
                 if (hcd->speed == HCD_USB3) {
-                        /* resume state is a xHCI internal state.
-                         * Do not report it to usb core.
-                         */
-                        if ((temp & PORT_PLS_MASK) != XDEV_RESUME)
-                                status |= (temp & PORT_PLS_MASK);
+                        xhci_hub_report_link_state(&status, temp);
                 }
                 if (bus_state->port_c_suspend & (1 << wIndex))
                         status |= 1 << USB_PORT_FEAT_C_SUSPEND;
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 23b4aefd1036..8275645889da 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -885,6 +885,17 @@ static void update_ring_for_set_deq_completion(struct xhci_hcd *xhci,
         num_trbs_free_temp = ep_ring->num_trbs_free;
         dequeue_temp = ep_ring->dequeue;
 
+        /* If we get two back-to-back stalls, and the first stalled transfer
+         * ends just before a link TRB, the dequeue pointer will be left on
+         * the link TRB by the code in the while loop.  So we have to update
+         * the dequeue pointer one segment further, or we'll jump off
+         * the segment into la-la-land.
+         */
+        if (last_trb(xhci, ep_ring, ep_ring->deq_seg, ep_ring->dequeue)) {
+                ep_ring->deq_seg = ep_ring->deq_seg->next;
+                ep_ring->dequeue = ep_ring->deq_seg->trbs;
+        }
+
         while (ep_ring->dequeue != dev->eps[ep_index].queued_deq_ptr) {
                 /* We have more usable TRBs */
                 ep_ring->num_trbs_free++;
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index de3d6e3e57be..55c0785810c9 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -341,7 +341,11 @@ struct xhci_op_regs {
 #define PORT_PLC        (1 << 22)
 /* port configure error change - port failed to configure its link partner */
 #define PORT_CEC        (1 << 23)
-/* bit 24 reserved */
+/* Cold Attach Status - xHC can set this bit to report device attached during
+ * Sx state. Warm port reset should be perfomed to clear this bit and move port
+ * to connected state.
+ */
+#define PORT_CAS        (1 << 24)
 /* wake on connect (enable) */
 #define PORT_WKCONN_E   (1 << 25)
 /* wake on disconnect (enable) */
diff --git a/drivers/usb/serial/metro-usb.c b/drivers/usb/serial/metro-usb.c
index 81423f7361db..d47eb06fe463 100644
--- a/drivers/usb/serial/metro-usb.c
+++ b/drivers/usb/serial/metro-usb.c
@@ -222,14 +222,6 @@ static int metrousb_open(struct tty_struct *tty, struct usb_serial_port *port)
         metro_priv->throttled = 0;
         spin_unlock_irqrestore(&metro_priv->lock, flags);
 
-        /*
-         * Force low_latency on so that our tty_push actually forces the data
-         * through, otherwise it is scheduled, and with high data rates (like
-         * with OHCI) data can get lost.
-         */
-        if (tty)
-                tty->low_latency = 1;
-
         /* Clear the urb pipe. */
         usb_clear_halt(serial->dev, port->interrupt_in_urb->pipe);
 
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index adf8ce72be50..417ab1b0aa30 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -497,6 +497,15 @@ static void option_instat_callback(struct urb *urb);
 
 /* MediaTek products */
 #define MEDIATEK_VENDOR_ID                      0x0e8d
+#define MEDIATEK_PRODUCT_DC_1COM                0x00a0
+#define MEDIATEK_PRODUCT_DC_4COM                0x00a5
+#define MEDIATEK_PRODUCT_DC_5COM                0x00a4
+#define MEDIATEK_PRODUCT_7208_1COM              0x7101
+#define MEDIATEK_PRODUCT_7208_2COM              0x7102
+#define MEDIATEK_PRODUCT_FP_1COM                0x0003
+#define MEDIATEK_PRODUCT_FP_2COM                0x0023
+#define MEDIATEK_PRODUCT_FPDC_1COM              0x0043
+#define MEDIATEK_PRODUCT_FPDC_2COM              0x0033
 
 /* Cellient products */
 #define CELLIENT_VENDOR_ID                      0x2692
@@ -554,6 +563,10 @@ static const struct option_blacklist_info net_intf1_blacklist = {
         .reserved = BIT(1),
 };
 
+static const struct option_blacklist_info net_intf2_blacklist = {
+        .reserved = BIT(2),
+};
+
 static const struct option_blacklist_info net_intf3_blacklist = {
         .reserved = BIT(3),
 };
@@ -1099,6 +1112,8 @@ static const struct usb_device_id option_ids[] = {
         { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1298, 0xff, 0xff, 0xff) },
         { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1299, 0xff, 0xff, 0xff) },
         { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1300, 0xff, 0xff, 0xff) },
+        { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1402, 0xff, 0xff, 0xff),
+                .driver_info = (kernel_ulong_t)&net_intf2_blacklist },
         { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x2002, 0xff,
           0xff, 0xff), .driver_info = (kernel_ulong_t)&zte_k3765_z_blacklist },
         { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x2003, 0xff, 0xff, 0xff) },
@@ -1240,6 +1255,17 @@ static const struct usb_device_id option_ids[] = {
         { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, 0x00a1, 0xff, 0x02, 0x01) },
         { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, 0x00a2, 0xff, 0x00, 0x00) },
         { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, 0x00a2, 0xff, 0x02, 0x01) },        /* MediaTek MT6276M modem & app port */
+        { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_DC_1COM, 0x0a, 0x00, 0x00) },
+        { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_DC_5COM, 0xff, 0x02, 0x01) },
+        { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_DC_5COM, 0xff, 0x00, 0x00) },
+        { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_DC_4COM, 0xff, 0x02, 0x01) },
+        { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_DC_4COM, 0xff, 0x00, 0x00) },
+        { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_7208_1COM, 0x02, 0x00, 0x00) },
+        { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_7208_2COM, 0x02, 0x02, 0x01) },
+        { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_FP_1COM, 0x0a, 0x00, 0x00) },
+        { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_FP_2COM, 0x0a, 0x00, 0x00) },
+        { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_FPDC_1COM, 0x0a, 0x00, 0x00) },
+        { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_FPDC_2COM, 0x0a, 0x00, 0x00) },
         { USB_DEVICE(CELLIENT_VENDOR_ID, CELLIENT_PRODUCT_MEN200) },
         { } /* Terminating entry */
 };
diff --git a/include/linux/pci.h b/include/linux/pci.h
index fefb4e19bf6a..d8c379dba6ad 100644
--- a/include/linux/pci.h
+++ b/include/linux/pci.h
@@ -176,8 +176,6 @@ enum pci_dev_flags {
         PCI_DEV_FLAGS_NO_D3 = (__force pci_dev_flags_t) 2,
         /* Provide indication device is assigned by a Virtual Machine Manager */
         PCI_DEV_FLAGS_ASSIGNED = (__force pci_dev_flags_t) 4,
-        /* Device causes system crash if in D3 during S3 sleep */
-        PCI_DEV_FLAGS_NO_D3_DURING_SLEEP = (__force pci_dev_flags_t) 8,
 };
 
 enum pci_irq_reroute_variant {