Merge remote-tracking branch 'spi/topic/qspi' into spi-next

1 files changed, 25 insertions, 2 deletions

diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index e1b3e69aeddc..887116dbce2c 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -74,7 +74,7 @@ struct spi_device {
         struct spi_master       *master;
         u32                     max_speed_hz;
         u8                      chip_select;
-        u8                      mode;
+        u16                     mode;
 #define SPI_CPHA        0x01                    /* clock phase */
 #define SPI_CPOL        0x02                    /* clock polarity */
 #define SPI_MODE_0      (0|0)                   /* (original MicroWire) */
@@ -87,6 +87,10 @@ struct spi_device {
 #define SPI_LOOP        0x20                    /* loopback mode */
 #define SPI_NO_CS       0x40                    /* 1 dev/bus, no chipselect */
 #define SPI_READY       0x80                    /* slave pulls low to pause */
+#define SPI_TX_DUAL     0x100                   /* transmit with 2 wires */
+#define SPI_TX_QUAD     0x200                   /* transmit with 4 wires */
+#define SPI_RX_DUAL     0x400                   /* receive with 2 wires */
+#define SPI_RX_QUAD     0x800                   /* receive with 4 wires */
         u8                      bits_per_word;
         int                     irq;
         void                    *controller_state;
@@ -256,6 +260,9 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv)
  * @busy: message pump is busy
  * @running: message pump is running
  * @rt: whether this queue is set to run as a realtime task
+ * @auto_runtime_pm: the core should ensure a runtime PM reference is held
+ *                   while the hardware is prepared, using the parent
+ *                   device for the spidev
  * @prepare_transfer_hardware: a message will soon arrive from the queue
  *      so the subsystem requests the driver to prepare the transfer hardware
  *      by issuing this call
@@ -380,11 +387,13 @@ struct spi_master {
         bool                            busy;
         bool                            running;
         bool                            rt;
+        bool                            auto_runtime_pm;
 
         int (*prepare_transfer_hardware)(struct spi_master *master);
         int (*transfer_one_message)(struct spi_master *master,
                                     struct spi_message *mesg);
         int (*unprepare_transfer_hardware)(struct spi_master *master);
+
         /* gpio chip select */
         int                     *cs_gpios;
 };
@@ -454,6 +463,10 @@ extern struct spi_master *spi_busnum_to_master(u16 busnum);
  * @rx_buf: data to be read (dma-safe memory), or NULL
  * @tx_dma: DMA address of tx_buf, if @spi_message.is_dma_mapped
  * @rx_dma: DMA address of rx_buf, if @spi_message.is_dma_mapped
+ * @tx_nbits: number of bits used for writting. If 0 the default
+ *      (SPI_NBITS_SINGLE) is used.
+ * @rx_nbits: number of bits used for reading. If 0 the default
+ *      (SPI_NBITS_SINGLE) is used.
  * @len: size of rx and tx buffers (in bytes)
  * @speed_hz: Select a speed other than the device default for this
  *      transfer. If 0 the default (from @spi_device) is used.
@@ -508,6 +521,11 @@ extern struct spi_master *spi_busnum_to_master(u16 busnum);
  * by the results of previous messages and where the whole transaction
  * ends when the chipselect goes intactive.
  *
+ * When SPI can transfer in 1x,2x or 4x. It can get this tranfer information
+ * from device through @tx_nbits and @rx_nbits. In Bi-direction, these
+ * two should both be set. User can set transfer mode with SPI_NBITS_SINGLE(1x)
+ * SPI_NBITS_DUAL(2x) and SPI_NBITS_QUAD(4x) to support these three transfer.
+ *
  * The code that submits an spi_message (and its spi_transfers)
  * to the lower layers is responsible for managing its memory.
  * Zero-initialize every field you don't set up explicitly, to
@@ -528,6 +546,11 @@ struct spi_transfer {
         dma_addr_t      rx_dma;
 
         unsigned        cs_change:1;
+        u8              tx_nbits;
+        u8              rx_nbits;
+#define SPI_NBITS_SINGLE        0x01 /* 1bit transfer */
+#define SPI_NBITS_DUAL          0x02 /* 2bits transfer */
+#define SPI_NBITS_QUAD          0x04 /* 4bits transfer */
         u8              bits_per_word;
         u16             delay_usecs;
         u32             speed_hz;
@@ -876,7 +899,7 @@ struct spi_board_info {
         /* mode becomes spi_device.mode, and is essential for chips
          * where the default of SPI_CS_HIGH = 0 is wrong.
          */
-        u8              mode;
+        u16             mode;
 
         /* ... may need additional spi_device chip config data here.
          * avoid stuff protocol drivers can set; but include stuff