[ARM] 5026/1: locomo: add .settype for gpio and several small fixes

irqs.h:
    * rename IRQ_LOCOMO_SPI_OVRN to IRQ_LOCOMO_SPI_REND
locomo.h:
    * add some definition for locomo spi controller
    * correct some errors
locomo.c:
    * correct some errors
    * add set_type for locomo gpio irq chip

Signed-off-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

1 files changed, 11 insertions, 8 deletions

diff --git a/include/asm-arm/hardware/locomo.h b/include/asm-arm/hardware/locomo.h
index adab77780ed3..fb0645de6f31 100644
--- a/include/asm-arm/hardware/locomo.h
+++ b/include/asm-arm/hardware/locomo.h
@@ -58,6 +58,11 @@
 #define LOCOMO_SPIMD    0x00            /* SPI mode setting */
 #define LOCOMO_SPICT    0x04            /* SPI mode control */
 #define LOCOMO_SPIST    0x08            /* SPI status */
+#define LOCOMO_SPI_TEND (1 << 3)        /* Transfer end bit */
+#define LOCOMO_SPI_REND (1 << 2)        /* Receive end bit */
+#define LOCOMO_SPI_RFW  (1 << 1)        /* write buffer bit */
+#define LOCOMO_SPI_RFR  (1)             /* read buffer bit */
+
 #define LOCOMO_SPIIS    0x10            /* SPI interrupt status */
 #define LOCOMO_SPIWE    0x14            /* SPI interrupt status write enable */
 #define LOCOMO_SPIIE    0x18            /* SPI interrupt enable */
@@ -66,16 +71,12 @@
 #define LOCOMO_SPIRD    0x24            /* SPI receive data read */
 #define LOCOMO_SPITS    0x28            /* SPI transfer data shift */
 #define LOCOMO_SPIRS    0x2C            /* SPI receive data shift */
-#define LOCOMO_SPI_TEND (1 << 3)        /* Transfer end bit */
-#define LOCOMO_SPI_OVRN (1 << 2)        /* Over Run bit */
-#define LOCOMO_SPI_RFW  (1 << 1)        /* write buffer bit */
-#define LOCOMO_SPI_RFR  (1)             /* read buffer bit */
 
 /* GPIO */
 #define LOCOMO_GPD              0x90    /* GPIO direction */
 #define LOCOMO_GPE              0x94    /* GPIO input enable */
 #define LOCOMO_GPL              0x98    /* GPIO level */
-#define LOCOMO_GPO              0x9c    /* GPIO out data setteing */
+#define LOCOMO_GPO              0x9c    /* GPIO out data setting */
 #define LOCOMO_GRIE             0xa0    /* GPIO rise detection */
 #define LOCOMO_GFIE             0xa4    /* GPIO fall detection */
 #define LOCOMO_GIS              0xa8    /* GPIO edge detection status */
@@ -96,6 +97,9 @@
 #define LOCOMO_GPIO_DAC_SDATA   LOCOMO_GPIO(10)
 #define LOCOMO_GPIO_DAC_SCK     LOCOMO_GPIO(11)
 #define LOCOMO_GPIO_DAC_SLOAD   LOCOMO_GPIO(12)
+#define LOCOMO_GPIO_CARD_DETECT LOCOMO_GPIO(13)
+#define LOCOMO_GPIO_WRITE_PROT  LOCOMO_GPIO(14)
+#define LOCOMO_GPIO_CARD_POWER  LOCOMO_GPIO(15)
 
 /* Start the definitions of the devices.  Each device has an initial
  * base address and a series of offsets from that base address. */
@@ -122,7 +126,7 @@
 /* Audio controller */
 #define LOCOMO_AUDIO            0x54
 #define LOCOMO_ACC              0x00    /* Audio clock */
-#define LOCOMO_PAIF             0x7C    /* PCM audio interface */
+#define LOCOMO_PAIF             0xD0    /* PCM audio interface */
 /* Audio clock */
 #define LOCOMO_ACC_XON          0x80
 #define LOCOMO_ACC_XEN          0x40
@@ -162,7 +166,7 @@ extern struct bus_type locomo_bus_type;
 #define LOCOMO_DEVID_AUDIO      3
 #define LOCOMO_DEVID_LED        4
 #define LOCOMO_DEVID_UART       5
-#define LOCOMO_DEVID_SPI                6
+#define LOCOMO_DEVID_SPI        6
 
 struct locomo_dev {
         struct device   dev;
@@ -204,7 +208,6 @@ int locomo_gpio_read_level(struct device *dev, unsigned int bits);
 int locomo_gpio_read_output(struct device *dev, unsigned int bits);
 void locomo_gpio_write(struct device *dev, unsigned int bits, unsigned int set);
 
-
 /* M62332 control function */
 void locomo_m62332_senddata(struct locomo_dev *ldev, unsigned int dac_data, int channel);