Merge tag 'v3.14-rc6' into devel

Linux 3.14-rc6

5 files changed, 32 insertions, 8 deletions

diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index 61ecd709a722..69932b7556cf 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -2433,6 +2433,24 @@ serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios,
         serial_dl_write(up, quot);
 
         /*
+         * XR17V35x UARTs have an extra fractional divisor register (DLD)
+         *
+         * We need to recalculate all of the registers, because DLM and DLL
+         * are already rounded to a whole integer.
+         *
+         * When recalculating we use a 32x clock instead of a 16x clock to
+         * allow 1-bit for rounding in the fractional part.
+         */
+        if (up->port.type == PORT_XR17V35X) {
+                unsigned int baud_x32 = (port->uartclk * 2) / baud;
+                u16 quot = baud_x32 / 32;
+                u8 quot_frac = DIV_ROUND_CLOSEST(baud_x32 % 32, 2);
+
+                serial_dl_write(up, quot);
+                serial_port_out(port, 0x2, quot_frac & 0xf);
+        }
+
+        /*
          * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR
          * is written without DLAB set, this mode will be disabled.
          */
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index faa64e646100..ed3113576740 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -391,7 +391,7 @@ static int dw8250_remove(struct platform_device *pdev)
         return 0;
 }
 
-#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
 static int dw8250_suspend(struct device *dev)
 {
         struct dw8250_data *data = dev_get_drvdata(dev);
@@ -409,7 +409,7 @@ static int dw8250_resume(struct device *dev)
 
         return 0;
 }
-#endif /* CONFIG_PM */
+#endif /* CONFIG_PM_SLEEP */
 
 #ifdef CONFIG_PM_RUNTIME
 static int dw8250_runtime_suspend(struct device *dev)
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 50228eed3b6f..0ff3e3624d4c 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -783,7 +783,8 @@ static int pci_netmos_9900_setup(struct serial_private *priv,
 {
         unsigned int bar;
 
-        if ((priv->dev->subsystem_device & 0xff00) == 0x3000) {
+        if ((priv->dev->device != PCI_DEVICE_ID_NETMOS_9865) &&
+            (priv->dev->subsystem_device & 0xff00) == 0x3000) {
                 /* netmos apparently orders BARs by datasheet layout, so serial
                  * ports get BARs 0 and 3 (or 1 and 4 for memmapped)
                  */
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index fa511ebab67c..77f035158d6c 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -738,9 +738,6 @@ static int serial_omap_startup(struct uart_port *port)
                         return retval;
                 }
                 disable_irq(up->wakeirq);
-        } else {
-                dev_info(up->port.dev, "no wakeirq for uart%d\n",
-                         up->port.line);
         }
 
         dev_dbg(up->port.dev, "serial_omap_startup+%d\n", up->port.line);
@@ -1604,8 +1601,11 @@ static int serial_omap_probe_rs485(struct uart_omap_port *up,
                                             flags & SER_RS485_RTS_AFTER_SEND);
                 if (ret < 0)
                         return ret;
-        } else
+        } else if (up->rts_gpio == -EPROBE_DEFER) {
+                return -EPROBE_DEFER;
+        } else {
                 up->rts_gpio = -EINVAL;
+        }
 
         if (of_property_read_u32_array(np, "rs485-rts-delay",
                                     rs485_delay, 2) == 0) {
@@ -1687,6 +1687,9 @@ static int serial_omap_probe(struct platform_device *pdev)
         up->port.iotype = UPIO_MEM;
         up->port.irq = uartirq;
         up->wakeirq = wakeirq;
+        if (!up->wakeirq)
+                dev_info(up->port.dev, "no wakeirq for uart%d\n",
+                         up->port.line);
 
         up->port.regshift = 2;
         up->port.fifosize = 64;
diff --git a/drivers/tty/serial/sirfsoc_uart.c b/drivers/tty/serial/sirfsoc_uart.c
index 49a2ffd101a7..b7bfe24d4ebc 100644
--- a/drivers/tty/serial/sirfsoc_uart.c
+++ b/drivers/tty/serial/sirfsoc_uart.c
@@ -542,8 +542,10 @@ static void sirfsoc_rx_tmo_process_tl(unsigned long param)
         wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl,
                         rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) |
                         SIRFUART_IO_MODE);
-        sirfsoc_uart_pio_rx_chars(port, 4 - sirfport->rx_io_count);
         spin_unlock_irqrestore(&sirfport->rx_lock, flags);
+        spin_lock(&port->lock);
+        sirfsoc_uart_pio_rx_chars(port, 4 - sirfport->rx_io_count);
+        spin_unlock(&port->lock);
         if (sirfport->rx_io_count == 4) {
                 spin_lock_irqsave(&sirfport->rx_lock, flags);
                 sirfport->rx_io_count = 0;