libertas/sdio: 8686: set ECSI bit for 1-bit transfers

When operating in 1-bit mode, SDAT1 is used as dedicated interrupt line.
However, the 8686 will only drive this line when the ECSI bit is set in
the CCCR_IF register.

Thanks to Alagu Sankar for pointing me in the right direction.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alagu Sankar <alagusankar@embwise.com>
Cc: Volker Ernst <volker.ernst@txtr.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1 files changed, 22 insertions, 0 deletions

diff --git a/drivers/net/wireless/libertas/if_sdio.c b/drivers/net/wireless/libertas/if_sdio.c
index 7a73f625273b..33206a98a572 100644
--- a/drivers/net/wireless/libertas/if_sdio.c
+++ b/drivers/net/wireless/libertas/if_sdio.c
@@ -34,6 +34,8 @@
 #include <linux/mmc/card.h>
 #include <linux/mmc/sdio_func.h>
 #include <linux/mmc/sdio_ids.h>
+#include <linux/mmc/sdio.h>
+#include <linux/mmc/host.h>
 
 #include "host.h"
 #include "decl.h"
@@ -942,6 +944,7 @@ static int if_sdio_probe(struct sdio_func *func,
         int ret, i;
         unsigned int model;
         struct if_sdio_packet *packet;
+        struct mmc_host *host = func->card->host;
 
         lbs_deb_enter(LBS_DEB_SDIO);
 
@@ -1022,6 +1025,25 @@ static int if_sdio_probe(struct sdio_func *func,
         if (ret)
                 goto disable;
 
+        /* For 1-bit transfers to the 8686 model, we need to enable the
+         * interrupt flag in the CCCR register. Set the MMC_QUIRK_LENIENT_FN0
+         * bit to allow access to non-vendor registers. */
+        if ((card->model == IF_SDIO_MODEL_8686) &&
+            (host->caps & MMC_CAP_SDIO_IRQ) &&
+            (host->ios.bus_width == MMC_BUS_WIDTH_1)) {
+                u8 reg;
+
+                func->card->quirks |= MMC_QUIRK_LENIENT_FN0;
+                reg = sdio_f0_readb(func, SDIO_CCCR_IF, &ret);
+                if (ret)
+                        goto release_int;
+
+                reg |= SDIO_BUS_ECSI;
+                sdio_f0_writeb(func, reg, SDIO_CCCR_IF, &ret);
+                if (ret)
+                        goto release_int;
+        }
+
         card->ioport = sdio_readb(func, IF_SDIO_IOPORT, &ret);
         if (ret)
                 goto release_int;