h8300: Switch h8300 to drivers/Kconfig

Convert the last remaining architecture to drivers/Kconfig.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

1 files changed, 1 insertions, 117 deletions

diff --git a/arch/h8300/Kconfig b/arch/h8300/Kconfig
index 303e4f9a79d1..3d6759ee382f 100644
--- a/arch/h8300/Kconfig
+++ b/arch/h8300/Kconfig
@@ -94,126 +94,10 @@ endmenu
 
 source "net/Kconfig"
 
-source "drivers/base/Kconfig"
-
-source "drivers/mtd/Kconfig"
-
-source "drivers/block/Kconfig"
-
-source "drivers/ide/Kconfig"
+source "drivers/Kconfig"
 
 source "arch/h8300/Kconfig.ide"
 
-source "drivers/net/Kconfig"
-
-#
-# input - input/joystick depends on it. As does USB.
-#
-source "drivers/input/Kconfig"
-
-menu "Character devices"
-
-config VT
-        bool "Virtual terminal"
-        ---help---
-          If you say Y here, you will get support for terminal devices with
-          display and keyboard devices. These are called "virtual" because you
-          can run several virtual terminals (also called virtual consoles) on
-          one physical terminal. This is rather useful, for example one
-          virtual terminal can collect system messages and warnings, another
-          one can be used for a text-mode user session, and a third could run
-          an X session, all in parallel. Switching between virtual terminals
-          is done with certain key combinations, usually Alt-<function key>.
-
-          The setterm command ("man setterm") can be used to change the
-          properties (such as colors or beeping) of a virtual terminal. The
-          man page console_codes(4) ("man console_codes") contains the special
-          character sequences that can be used to change those properties
-          directly. The fonts used on virtual terminals can be changed with
-          the setfont ("man setfont") command and the key bindings are defined
-          with the loadkeys ("man loadkeys") command.
-
-          You need at least one virtual terminal device in order to make use
-          of your keyboard and monitor. Therefore, only people configuring an
-          embedded system would want to say N here in order to save some
-          memory; the only way to log into such a system is then via a serial
-          or network connection.
-
-          If unsure, say Y, or else you won't be able to do much with your new
-          shiny Linux system :-)
-
-config VT_CONSOLE
-        bool "Support for console on virtual terminal"
-        depends on VT
-        ---help---
-          The system console is the device which receives all kernel messages
-          and warnings and which allows logins in single user mode. If you
-          answer Y here, a virtual terminal (the device used to interact with
-          a physical terminal) can be used as system console. This is the most
-          common mode of operations, so you should say Y here unless you want
-          the kernel messages be output only to a serial port (in which case
-          you should say Y to "Console on serial port", below).
-
-          If you do say Y here, by default the currently visible virtual
-          terminal (/dev/tty0) will be used as system console. You can change
-          that with a kernel command line option such as "console=tty3" which
-          would use the third virtual terminal as system console. (Try "man
-          bootparam" or see the documentation of your boot loader (lilo or
-          loadlin) about how to pass options to the kernel at boot time.)
-
-          If unsure, say Y.
-
-config HW_CONSOLE
-        bool
-        depends on VT
-        default y
-
-comment "Unix98 PTY support"
-
-config UNIX98_PTYS
-        bool "Unix98 PTY support"
-        ---help---
-          A pseudo terminal (PTY) is a software device consisting of two
-          halves: a master and a slave. The slave device behaves identical to
-          a physical terminal; the master device is used by a process to
-          read data from and write data to the slave, thereby emulating a
-          terminal. Typical programs for the master side are telnet servers
-          and xterms.
-
-          Linux has traditionally used the BSD-like names /dev/ptyxx for
-          masters and /dev/ttyxx for slaves of pseudo terminals. This scheme
-          has a number of problems. The GNU C library glibc 2.1 and later,
-          however, supports the Unix98 naming standard: in order to acquire a
-          pseudo terminal, a process opens /dev/ptmx; the number of the pseudo
-          terminal is then made available to the process and the pseudo
-          terminal slave can be accessed as /dev/pts/<number>. What was
-          traditionally /dev/ttyp2 will then be /dev/pts/2, for example.
-
-          The entries in /dev/pts/ are created on the fly by a virtual
-          file system; therefore, if you say Y here you should say Y to
-          "/dev/pts file system for Unix98 PTYs" as well.
-
-          If you want to say Y here, you need to have the C library glibc 2.1
-          or later (equal to libc-6.1, check with "ls -l /lib/libc.so.*").
-          Read the instructions in <file:Documentation/Changes> pertaining to
-          pseudo terminals. It's safe to say N.
-
-source "drivers/char/pcmcia/Kconfig"
-
-source "drivers/tty/serial/Kconfig"
-
-source "drivers/i2c/Kconfig"
-
-source "drivers/hwmon/Kconfig"
-
-source "drivers/usb/Kconfig"
-
-source "drivers/uwb/Kconfig"
-
-endmenu
-
-source "drivers/staging/Kconfig"
-
 source "fs/Kconfig"
 
 source "arch/h8300/Kconfig.debug"