ARM: pxa/raumfeld: display initialisation fixes

The display requires some milliseconds between GPIO_TFT_VA_EN
and GPIO_DISPLAY_ENABLE. Reorder initialisation to comply with
the display spec.

Also tune timings for better compliance with the spec.

Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

1 files changed, 15 insertions, 14 deletions

diff --git a/arch/arm/mach-pxa/raumfeld.c b/arch/arm/mach-pxa/raumfeld.c
index 8e5b3d8a86be..9caa5e5c8d94 100644
--- a/arch/arm/mach-pxa/raumfeld.c
+++ b/arch/arm/mach-pxa/raumfeld.c
@@ -573,10 +573,10 @@ static struct pxafb_mode_info sharp_lq043t3dx02_mode = {
         .xres           = 480,
         .yres           = 272,
         .bpp            = 16,
-        .hsync_len      = 4,
+        .hsync_len      = 41,
         .left_margin    = 2,
         .right_margin   = 1,
-        .vsync_len      = 1,
+        .vsync_len      = 10,
         .upper_margin   = 3,
         .lower_margin   = 1,
         .sync           = 0,
@@ -596,30 +596,31 @@ static void __init raumfeld_lcd_init(void)
 {
         int ret;
 
-        pxa_set_fb_info(NULL, &raumfeld_sharp_lcd_info);
-
-        /* Hardware revision 2 has the backlight regulator controlled
-         * by an LT3593, earlier and later devices use PWM for that. */
-        if ((system_rev & 0xff) == 2) {
-                platform_device_register(&raumfeld_lt3593_device);
-        } else {
-                mfp_cfg_t raumfeld_pwm_pin_config = GPIO17_PWM0_OUT;
-                pxa3xx_mfp_config(&raumfeld_pwm_pin_config, 1);
-                platform_device_register(&raumfeld_pwm_backlight_device);
-        }
-
         ret = gpio_request(GPIO_TFT_VA_EN, "display VA enable");
         if (ret < 0)
                 pr_warning("Unable to request GPIO_TFT_VA_EN\n");
         else
                 gpio_direction_output(GPIO_TFT_VA_EN, 1);
 
+        msleep(100);
+
         ret = gpio_request(GPIO_DISPLAY_ENABLE, "display enable");
         if (ret < 0)
                 pr_warning("Unable to request GPIO_DISPLAY_ENABLE\n");
         else
                 gpio_direction_output(GPIO_DISPLAY_ENABLE, 1);
 
+        /* Hardware revision 2 has the backlight regulator controlled
+         * by an LT3593, earlier and later devices use PWM for that. */
+        if ((system_rev & 0xff) == 2) {
+                platform_device_register(&raumfeld_lt3593_device);
+        } else {
+                mfp_cfg_t raumfeld_pwm_pin_config = GPIO17_PWM0_OUT;
+                pxa3xx_mfp_config(&raumfeld_pwm_pin_config, 1);
+                platform_device_register(&raumfeld_pwm_backlight_device);
+        }
+
+        pxa_set_fb_info(NULL, &raumfeld_sharp_lcd_info);
         platform_device_register(&pxa3xx_device_gcu);
 }