[PATCH] I2C: documentation update 1/3

This patch just changes the extension of Documentation/i2c/chips/smsc47b397.txt
to none - to conform with naming in i2c subsystem directory.

Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1 files changed, 146 insertions, 0 deletions

diff --git a/Documentation/i2c/chips/smsc47b397 b/Documentation/i2c/chips/smsc47b397
new file mode 100644
index 000000000000..4737bb6109da
--- /dev/null
+++ b/Documentation/i2c/chips/smsc47b397
@@ -0,0 +1,146 @@
+November 23, 2004
+
+The following specification describes the SMSC LPC47B397-NC sensor chip
+(for which there is no public datasheet available).  This document was
+provided by Craig Kelly (In-Store Broadcast Network) and edited/corrected
+by Mark M. Hoffman <mhoffman@lightlink.com>.
+
+* * * * *
+
+Methods for detecting the HP SIO and reading the thermal data on a dc7100.
+
+The thermal information on the dc7100 is contained in the SIO Hardware Monitor
+(HWM).  The information is accessed through an index/data pair.  The index/data
+pair is located at the HWM Base Address + 0 and the HWM Base Address + 1.  The
+HWM Base address can be obtained from Logical Device 8, registers 0x60 (MSB)
+and 0x61 (LSB).  Currently we are using 0x480 for the HWM Base Address and
+0x480 and 0x481 for the index/data pair.
+
+Reading temperature information.
+The temperature information is located in the following registers:
+Temp1           0x25    (Currently, this reflects the CPU temp on all systems).
+Temp2           0x26
+Temp3           0x27
+Temp4           0x80
+
+Programming Example
+The following is an example of how to read the HWM temperature registers:
+MOV     DX,480H
+MOV     AX,25H
+OUT     DX,AL
+MOV     DX,481H
+IN      AL,DX
+
+AL contains the data in hex, the temperature in Celsius is the decimal
+equivalent.
+
+Ex: If AL contains 0x2A, the temperature is 42 degrees C.
+
+Reading tach information.
+The fan speed information is located in the following registers:
+                LSB     MSB
+Tach1           0x28    0x29    (Currently, this reflects the CPU
+                                fan speed on all systems).
+Tach2           0x2A    0x2B
+Tach3           0x2C    0x2D
+Tach4           0x2E    0x2F
+
+Important!!!
+Reading the tach LSB locks the tach MSB.
+The LSB Must be read first.
+
+How to convert the tach reading to RPM.
+The tach reading (TCount) is given by:  (Tach MSB * 256) + (Tach LSB)
+The SIO counts the number of 90kHz (11.111us) pulses per revolution.
+RPM = 60/(TCount * 11.111us)
+
+Example:
+Reg 0x28 = 0x9B
+Reg 0x29 = 0x08
+
+TCount = 0x89B = 2203
+
+RPM = 60 / (2203 * 11.11111 E-6) = 2451 RPM
+
+Obtaining the SIO version.
+
+CONFIGURATION SEQUENCE
+To program the configuration registers, the following sequence must be followed:
+1. Enter Configuration Mode
+2. Configure the Configuration Registers
+3. Exit Configuration Mode.
+
+Enter Configuration Mode
+To place the chip into the Configuration State The config key (0x55) is written
+to the CONFIG PORT (0x2E).
+
+Configuration Mode
+In configuration mode, the INDEX PORT is located at the CONFIG PORT address and
+the DATA PORT is at INDEX PORT address + 1.
+
+The desired configuration registers are accessed in two steps:
+a.      Write the index of the Logical Device Number Configuration Register
+        (i.e., 0x07) to the INDEX PORT and then write the number of the
+        desired logical device to the DATA PORT.
+
+b.      Write the address of the desired configuration register within the
+        logical device to the INDEX PORT and then write or read the config-
+        uration register through the DATA PORT.
+
+Note: If accessing the Global Configuration Registers, step (a) is not required.
+
+Exit Configuration Mode
+To exit the Configuration State the write 0xAA to the CONFIG PORT (0x2E).
+The chip returns to the RUN State.  (This is important).
+
+Programming Example
+The following is an example of how to read the SIO Device ID located at 0x20
+
+; ENTER CONFIGURATION MODE
+MOV     DX,02EH
+MOV     AX,055H
+OUT     DX,AL
+; GLOBAL CONFIGURATION  REGISTER
+MOV     DX,02EH
+MOV     AL,20H
+OUT     DX,AL
+; READ THE DATA
+MOV     DX,02FH
+IN      AL,DX
+; EXIT CONFIGURATION MODE
+MOV     DX,02EH
+MOV     AX,0AAH
+OUT     DX,AL
+
+The registers of interest for identifying the SIO on the dc7100 are Device ID
+(0x20) and Device Rev  (0x21).
+
+The Device ID will read 0X6F
+The Device Rev currently reads 0x01
+
+Obtaining the HWM Base Address.
+The following is an example of how to read the HWM Base Address located in
+Logical Device 8.
+
+; ENTER CONFIGURATION MODE
+MOV     DX,02EH
+MOV     AX,055H
+OUT     DX,AL
+; CONFIGURE REGISTER CRE0,
+; LOGICAL DEVICE 8
+MOV     DX,02EH
+MOV     AL,07H
+OUT     DX,AL ;Point to LD# Config Reg
+MOV     DX,02FH
+MOV     AL, 08H
+OUT     DX,AL;Point to Logical Device 8
+;
+MOV     DX,02EH
+MOV     AL,60H
+OUT     DX,AL   ; Point to HWM Base Addr MSB
+MOV     DX,02FH
+IN      AL,DX   ; Get MSB of HWM Base Addr
+; EXIT CONFIGURATION MODE
+MOV     DX,02EH
+MOV     AX,0AAH
+OUT     DX,AL