Merge branch 'irq/for-gpio' into irq/core

Merge the request/release callbacks which are in a separate branch for
consumption by the gpio folks.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

6 files changed, 97 insertions, 13 deletions

diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index 34dc40cffdfd..af9b4a0d902b 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -91,7 +91,7 @@ Boards:
   compatible = "ti,omap3-beagle", "ti,omap3"
 
 - OMAP3 Tobi with Overo : Commercial expansion board with daughter board
-  compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3"
+  compatible = "gumstix,omap3-overo-tobi", "gumstix,omap3-overo", "ti,omap3"
 
 - OMAP4 SDP : Software Development Board
   compatible = "ti,omap4-sdp", "ti,omap4430"
diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt
index a6a352c2771e..5992dceec7af 100644
--- a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt
+++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt
@@ -21,9 +21,9 @@ Required Properties:
     must appear in the same order as the output clocks.
   - #clock-cells: Must be 1
   - clock-output-names: The name of the clocks as free-form strings
-  - renesas,indices: Indices of the gate clocks into the group (0 to 31)
+  - renesas,clock-indices: Indices of the gate clocks into the group (0 to 31)
 
-The clocks, clock-output-names and renesas,indices properties contain one
+The clocks, clock-output-names and renesas,clock-indices properties contain one
 entry per gate clock. The MSTP groups are sparsely populated. Unimplemented
 gate clocks must not be declared.
 
diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
index 68b83ecc3850..ee9be9961524 100644
--- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
+++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
@@ -1,12 +1,16 @@
 * Freescale Smart Direct Memory Access (SDMA) Controller for i.MX
 
 Required properties:
-- compatible : Should be "fsl,imx31-sdma", "fsl,imx31-to1-sdma",
-  "fsl,imx31-to2-sdma", "fsl,imx35-sdma", "fsl,imx35-to1-sdma",
-  "fsl,imx35-to2-sdma", "fsl,imx51-sdma", "fsl,imx53-sdma" or
-  "fsl,imx6q-sdma". The -to variants should be preferred since they
-  allow to determnine the correct ROM script addresses needed for
-  the driver to work without additional firmware.
+- compatible : Should be one of
+      "fsl,imx25-sdma"
+      "fsl,imx31-sdma", "fsl,imx31-to1-sdma", "fsl,imx31-to2-sdma"
+      "fsl,imx35-sdma", "fsl,imx35-to1-sdma", "fsl,imx35-to2-sdma"
+      "fsl,imx51-sdma"
+      "fsl,imx53-sdma"
+      "fsl,imx6q-sdma"
+  The -to variants should be preferred since they allow to determnine the
+  correct ROM script addresses needed for the driver to work without additional
+  firmware.
 - reg : Should contain SDMA registers location and length
 - interrupts : Should contain SDMA interrupt
 - #dma-cells : Must be <3>.
diff --git a/Documentation/devicetree/bindings/net/opencores-ethoc.txt b/Documentation/devicetree/bindings/net/opencores-ethoc.txt
new file mode 100644
index 000000000000..2dc127c30d9b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/opencores-ethoc.txt
@@ -0,0 +1,22 @@
+* OpenCores MAC 10/100 Mbps
+
+Required properties:
+- compatible: Should be "opencores,ethoc".
+- reg: two memory regions (address and length),
+  first region is for the device registers and descriptor rings,
+  second is for the device packet memory.
+- interrupts: interrupt for the device.
+
+Optional properties:
+- clocks: phandle to refer to the clk used as per
+  Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Examples:
+
+        enet0: ethoc@fd030000 {
+                compatible = "opencores,ethoc";
+                reg = <0xfd030000 0x4000 0xfd800000 0x4000>;
+                interrupts = <1>;
+                local-mac-address = [00 50 c2 13 6f 00];
+                clocks = <&osc>;
+        };
diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt
new file mode 100644
index 000000000000..3dd3d0bf112f
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt
@@ -0,0 +1,58 @@
+STMicroelectronics SoC DWMAC glue layer controller
+
+The device node has following properties.
+
+Required properties:
+ - compatible   : Can be "st,stih415-dwmac", "st,stih416-dwmac" or
+   "st,stid127-dwmac".
+ - reg          : Offset of the glue configuration register map in system
+   configuration regmap pointed by st,syscon property and size.
+
+ - reg-names    : Should be "sti-ethconf".
+
+ - st,syscon    : Should be phandle to system configuration node which
+   encompases this glue registers.
+
+ - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be
+   wired up in from different sources. One via TXCLK pin and other via CLK_125
+   pin. This wiring is totally board dependent. However the retiming glue
+   logic should be configured accordingly. Possible values for this property
+
+           "txclk" - if 125Mhz clock is wired up via txclk line.
+           "clk_125" - if 125Mhz clock is wired up via clk_125 line.
+
+   This property is only valid for Giga bit setup( GMII, RGMII), and it is
+   un-used for non-giga bit (MII and RMII) setups. Also note that internal
+   clockgen can not generate stable 125Mhz clock.
+
+ - st,ext-phyclk: This boolean property indicates who is generating the clock
+  for tx and rx. This property is only valid for RMII case where the clock can
+  be generated from the MAC or PHY.
+
+ - clock-names: should be "sti-ethclk".
+ - clocks: Should point to ethernet clockgen which can generate phyclk.
+
+
+Example:
+
+ethernet0: dwmac@fe810000 {
+        device_type     = "network";
+        compatible      = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+        reg             = <0xfe810000 0x8000>, <0x8bc 0x4>;
+        reg-names       = "stmmaceth", "sti-ethconf";
+        interrupts      = <0 133 0>, <0 134 0>, <0 135 0>;
+        interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+        phy-mode        = "mii";
+
+        st,syscon       = <&syscfg_rear>;
+
+        snps,pbl        = <32>;
+        snps,mixed-burst;
+
+        resets          = <&softreset STIH416_ETH0_SOFTRESET>;
+        reset-names     = "stmmaceth";
+        pinctrl-0       = <&pinctrl_mii0>;
+        pinctrl-names   = "default";
+        clocks          = <&CLK_S_GMAC0_PHY>;
+        clock-names     = "stmmaceth";
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt
index 9e9e9ef9f852..c119debe6bab 100644
--- a/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt
@@ -1,4 +1,4 @@
-Broadcom Capri Pin Controller
+Broadcom BCM281xx Pin Controller
 
 This is a pin controller for the Broadcom BCM281xx SoC family, which includes
 BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs.
@@ -7,14 +7,14 @@ BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs.
 
 Required Properties:
 
-- compatible:   Must be "brcm,capri-pinctrl".
+- compatible:   Must be "brcm,bcm11351-pinctrl"
 - reg:          Base address of the PAD Controller register block and the size
                 of the block.
 
 For example, the following is the bare minimum node:
 
         pinctrl@35004800 {
-                compatible = "brcm,capri-pinctrl";
+                compatible = "brcm,bcm11351-pinctrl";
                 reg = <0x35004800 0x430>;
         };
 
@@ -119,7 +119,7 @@ Optional Properties (for HDMI pins):
 Example:
 // pin controller node
 pinctrl@35004800 {
-        compatible = "brcm,capri-pinctrl";
+        compatible = "brcmbcm11351-pinctrl";
         reg = <0x35004800 0x430>;
 
         // pin configuration node