Merge 3.14-rc4 into usb-next

We want the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

2 files changed, 59 insertions, 1 deletions

diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index 34dc40cffdfd..af9b4a0d902b 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -91,7 +91,7 @@ Boards:
   compatible = "ti,omap3-beagle", "ti,omap3"
 
 - OMAP3 Tobi with Overo : Commercial expansion board with daughter board
-  compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3"
+  compatible = "gumstix,omap3-overo-tobi", "gumstix,omap3-overo", "ti,omap3"
 
 - OMAP4 SDP : Software Development Board
   compatible = "ti,omap4-sdp", "ti,omap4430"
diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt
new file mode 100644
index 000000000000..3dd3d0bf112f
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt
@@ -0,0 +1,58 @@
+STMicroelectronics SoC DWMAC glue layer controller
+
+The device node has following properties.
+
+Required properties:
+ - compatible   : Can be "st,stih415-dwmac", "st,stih416-dwmac" or
+   "st,stid127-dwmac".
+ - reg          : Offset of the glue configuration register map in system
+   configuration regmap pointed by st,syscon property and size.
+
+ - reg-names    : Should be "sti-ethconf".
+
+ - st,syscon    : Should be phandle to system configuration node which
+   encompases this glue registers.
+
+ - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be
+   wired up in from different sources. One via TXCLK pin and other via CLK_125
+   pin. This wiring is totally board dependent. However the retiming glue
+   logic should be configured accordingly. Possible values for this property
+
+           "txclk" - if 125Mhz clock is wired up via txclk line.
+           "clk_125" - if 125Mhz clock is wired up via clk_125 line.
+
+   This property is only valid for Giga bit setup( GMII, RGMII), and it is
+   un-used for non-giga bit (MII and RMII) setups. Also note that internal
+   clockgen can not generate stable 125Mhz clock.
+
+ - st,ext-phyclk: This boolean property indicates who is generating the clock
+  for tx and rx. This property is only valid for RMII case where the clock can
+  be generated from the MAC or PHY.
+
+ - clock-names: should be "sti-ethclk".
+ - clocks: Should point to ethernet clockgen which can generate phyclk.
+
+
+Example:
+
+ethernet0: dwmac@fe810000 {
+        device_type     = "network";
+        compatible      = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+        reg             = <0xfe810000 0x8000>, <0x8bc 0x4>;
+        reg-names       = "stmmaceth", "sti-ethconf";
+        interrupts      = <0 133 0>, <0 134 0>, <0 135 0>;
+        interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+        phy-mode        = "mii";
+
+        st,syscon       = <&syscfg_rear>;
+
+        snps,pbl        = <32>;
+        snps,mixed-burst;
+
+        resets          = <&softreset STIH416_ETH0_SOFTRESET>;
+        reset-names     = "stmmaceth";
+        pinctrl-0       = <&pinctrl_mii0>;
+        pinctrl-names   = "default";
+        clocks          = <&CLK_S_GMAC0_PHY>;
+        clock-names     = "stmmaceth";
+};