pinctrl: add samsung pinctrl and gpiolib driver

Add a new device tree enabled pinctrl and gpiolib driver for Samsung
SoC's. This driver provides a common and extensible framework for all
Samsung SoC's to interface with the pinctrl and gpiolib subsystems. This
driver supports only device tree based instantiation and hence can be
used only on those Samsung platforms that have device tree enabled.

This driver is split into two parts: the pinctrl interface and the gpiolib
interface. The pinctrl interface registers pinctrl devices with the pinctrl
subsystem and gpiolib interface registers gpio chips with the gpiolib
subsystem. The information about the pins, pin groups, pin functions and
gpio chips, which are SoC specific, are parsed from device tree node.

Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

1 files changed, 196 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
new file mode 100644
index 000000000000..03dee50532f5
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
@@ -0,0 +1,196 @@
+Samsung GPIO and Pin Mux/Config controller
+
+Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware
+controller. It controls the input/output settings on the available pads/pins
+and also provides ability to multiplex and configure the output of various
+on-chip controllers onto these pads.
+
+Required Properties:
+- compatible: should be one of the following.
+  - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller.
+  - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller.
+
+- reg: Base address of the pin controller hardware module and length of
+  the address space it occupies.
+
+- interrupts: interrupt specifier for the controller. The format and value of
+  the interrupt specifier depends on the interrupt parent for the controller.
+
+- Pin mux/config groups as child nodes: The pin mux (selecting pin function
+  mode) and pin config (pull up/down, driver strength) settings are represented
+  as child nodes of the pin-controller node. There should be atleast one
+  child node and there is no limit on the count of these child nodes.
+
+  The child node should contain a list of pin(s) on which a particular pin
+  function selection or pin configuration (or both) have to applied. This
+  list of pins is specified using the property name "samsung,pins". There
+  should be atleast one pin specfied for this property and there is no upper
+  limit on the count of pins that can be specified. The pins are specified
+  using pin names which are derived from the hardware manual of the SoC. As
+  an example, the pins in GPA0 bank of the pin controller can be represented
+  as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case.
+  The format of the pin names should be (as per the hardware manual)
+  "[pin bank name]-[pin number within the bank]".
+
+  The pin function selection that should be applied on the pins listed in the
+  child node is specified using the "samsung,pin-function" property. The value
+  of this property that should be applied to each of the pins listed in the
+  "samsung,pins" property should be picked from the hardware manual of the SoC
+  for the specified pin group. This property is optional in the child node if
+  no specific function selection is desired for the pins listed in the child
+  node. The value of this property is used as-is to program the pin-controller
+  function selector register of the pin-bank.
+
+  The child node can also optionally specify one or more of the pin
+  configuration that should be applied on all the pins listed in the
+  "samsung,pins" property of the child node. The following pin configuration
+  properties are supported.
+
+  - samsung,pin-pud: Pull up/down configuration.
+  - samsung,pin-drv: Drive strength configuration.
+  - samsung,pin-pud-pdn: Pull up/down configuration in power down mode.
+  - samsung,pin-drv-pdn: Drive strength configuration in power down mode.
+
+  The values specified by these config properties should be derived from the
+  hardware manual and these values are programmed as-is into the pin
+  pull up/down and driver strength register of the pin-controller.
+
+  Note: A child should include atleast a pin function selection property or
+  pin configuration property (one or more) or both.
+
+  The client nodes that require a particular pin function selection and/or
+  pin configuration should use the bindings listed in the "pinctrl-bindings.txt"
+  file.
+
+External GPIO and Wakeup Interrupts:
+
+The controller supports two types of external interrupts over gpio. The first
+is the external gpio interrupt and second is the external wakeup interrupts.
+The difference between the two is that the external wakeup interrupts can be
+used as system wakeup events.
+
+A. External GPIO Interrupts: For supporting external gpio interrupts, the
+   following properties should be specified in the pin-controller device node.
+
+- interrupt-controller: identifies the controller node as interrupt-parent.
+- #interrupt-cells: the value of this property should be 2.
+  - First Cell: represents the external gpio interrupt number local to the
+    external gpio interrupt space of the controller.
+  - Second Cell: flags to identify the type of the interrupt
+    - 1 = rising edge triggered
+    - 2 = falling edge triggered
+    - 3 = rising and falling edge triggered
+    - 4 = high level triggered
+    - 8 = low level triggered
+
+B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
+   child node representing the external wakeup interrupt controller should be
+   included in the pin-controller device node. This child node should include
+   the following properties.
+
+   - compatible: identifies the type of the external wakeup interrupt controller
+     The possible values are:
+     - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung Exynos4210 SoC.
+   - interrupt-parent: phandle of the interrupt parent to which the external
+     wakeup interrupts are forwarded to.
+   - interrupt-controller: identifies the node as interrupt-parent.
+   - #interrupt-cells: the value of this property should be 2
+     - First Cell: represents the external wakeup interrupt number local to
+       the external wakeup interrupt space of the controller.
+     - Second Cell: flags to identify the type of the interrupt
+       - 1 = rising edge triggered
+       - 2 = falling edge triggered
+       - 3 = rising and falling edge triggered
+       - 4 = high level triggered
+       - 8 = low level triggered
+
+Aliases:
+
+All the pin controller nodes should be represented in the aliases node using
+the following format 'pinctrl{n}' where n is a unique number for the alias.
+
+Example 1: A pin-controller node with pin groups.
+
+        pinctrl_0: pinctrl@11400000 {
+                compatible = "samsung,pinctrl-exynos4210";
+                reg = <0x11400000 0x1000>;
+                interrupts = <0 47 0>;
+
+                uart0_data: uart0-data {
+                        samsung,pins = "gpa0-0", "gpa0-1";
+                        samsung,pin-function = <2>;
+                        samsung,pin-pud = <0>;
+                        samsung,pin-drv = <0>;
+                };
+
+                uart0_fctl: uart0-fctl {
+                        samsung,pins = "gpa0-2", "gpa0-3";
+                        samsung,pin-function = <2>;
+                        samsung,pin-pud = <0>;
+                        samsung,pin-drv = <0>;
+                };
+
+                uart1_data: uart1-data {
+                        samsung,pins = "gpa0-4", "gpa0-5";
+                        samsung,pin-function = <2>;
+                        samsung,pin-pud = <0>;
+                        samsung,pin-drv = <0>;
+                };
+
+                uart1_fctl: uart1-fctl {
+                        samsung,pins = "gpa0-6", "gpa0-7";
+                        samsung,pin-function = <2>;
+                        samsung,pin-pud = <0>;
+                        samsung,pin-drv = <0>;
+                };
+
+                i2c2_bus: i2c2-bus {
+                        samsung,pins = "gpa0-6", "gpa0-7";
+                        samsung,pin-function = <3>;
+                        samsung,pin-pud = <3>;
+                        samsung,pin-drv = <0>;
+                };
+        };
+
+Example 2: A pin-controller node with external wakeup interrupt controller node.
+
+        pinctrl_1: pinctrl@11000000 {
+                compatible = "samsung,pinctrl-exynos4210";
+                reg = <0x11000000 0x1000>;
+                interrupts = <0 46 0>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+
+                wakup_eint: wakeup-interrupt-controller {
+                        compatible = "samsung,exynos4210-wakeup-eint";
+                        interrupt-parent = <&gic>;
+                        interrupt-controller;
+                        #interrupt-cells = <2>;
+                        interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+                                        <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
+                                        <0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
+                                        <0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>,
+                                        <0 32 0>;
+                };
+        };
+
+Example 3: A uart client node that supports 'default' and 'flow-control' states.
+
+        uart@13800000 {
+                compatible = "samsung,exynos4210-uart";
+                reg = <0x13800000 0x100>;
+                interrupts = <0 52 0>;
+                pinctrl-names = "default", "flow-control;
+                pinctrl-0 = <&uart0_data>;
+                pinctrl-1 = <&uart0_data &uart0_fctl>;
+        };
+
+Example 4: Set up the default pin state for uart controller.
+
+        static int s3c24xx_serial_probe(struct platform_device *pdev) {
+                struct pinctrl *pinctrl;
+                ...
+                ...
+                pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
+        }