Merge tag 'for-linus-20140127' of git://git.infradead.org/linux-mtd

Pull MTD updates from Brian Norris:
 - Add me (Brian Norris) as an additional MTD maintainer (it'd be nice to get
   David's "ack" for this; I'm sure he approves, but he's been pretty silent
   lately)
 - Add Ezequiel Garcie as maintainer for the pxa3xx NAND driver
 - Last (?) round of pxa3xx improvements for supporting Armada 370/XP
 - Typical churn in driver boilerplate (OOM messages, printk()'s, devm_*, etc.)
 - Quad read mode support for SPI NOR driver (m25p80)
 - Update Davinci NAND driver to prepare for use on new platforms
 - Begin to kill off NAND_MAX_{PAGE,OOB}SIZE macros; more work is pending
 - Miscellaneous NAND device support (new IDs)
 - Add READ RETRY support for Micron MLC NAND
 - Support new GPMI NAND ECC layout device-tree binding
 - Avoid mapping stack/vmalloc() memory for GPMI NAND DMA

* tag 'for-linus-20140127' of git://git.infradead.org/linux-mtd: (151 commits)
  mtd: gpmi: add sanity check when mapping DMA for read_buf/write_buf
  mtd: gpmi: allocate a proper buffer for non ECC read/write
  mtd: m25p80: Set rx_nbits for Quad SPI transfers
  mtd: m25p80: Enable Quad SPI read transfers for s25fl512s
  mtd: s3c2410: Merge plat/regs-nand.h into s3c2410.c
  mtd: mtdram: add missing 'const'
  mtd: m25p80: assign default read command
  mtd: nuc900_nand: remove redundant return value check of platform_get_resource()
  mtd: plat_nand: remove redundant return value check of platform_get_resource()
  mtd: nand: add Intel manufacturer ID
  mtd: nand: add SanDisk manufacturer ID
  mtd: nand: add support for Samsung K9LCG08U0B
  mtd: nand: pxa3xx: Add support for 2048 bytes page size devices
  mtd: m25p80: Use OPCODE_QUAD_READ_4B for 4-byte addressing
  mtd: nand: don't use {read,write}_buf for 8-bit transfers
  mtd: nand: use __packed shorthand
  mtd: nand: support Micron READ RETRY
  mtd: nand: add generic READ RETRY support
  mtd: nand: add ONFI vendor block for Micron
  mtd: nand: localize ECC failures per page
  ...

1 files changed, 0 insertions, 46 deletions

diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt
deleted file mode 100644
index 3545ea704b50..000000000000
--- a/Documentation/devicetree/bindings/arm/davinci/nand.txt
+++ /dev/null
@@ -1,46 +0,0 @@
-* Texas Instruments Davinci NAND
-
-This file provides information, what the device node for the
-davinci nand interface contain.
-
-Required properties:
-- compatible: "ti,davinci-nand";
-- reg : contain 2 offset/length values:
-        - offset and length for the access window
-        - offset and length for accessing the aemif control registers
-- ti,davinci-chipselect: Indicates on the davinci_nand driver which
-                         chipselect is used for accessing the nand.
-
-Recommended properties :
-- ti,davinci-mask-ale: mask for ale
-- ti,davinci-mask-cle: mask for cle
-- ti,davinci-mask-chipsel: mask for chipselect
-- ti,davinci-ecc-mode: ECC mode valid values for davinci driver:
-                - "none"
-                - "soft"
-                - "hw"
-- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4.
-- ti,davinci-nand-buswidth: buswidth 8 or 16
-- ti,davinci-nand-use-bbt: use flash based bad block table support.
-
-nand device bindings may contain additional sub-nodes describing
-partitions of the address space. See partition.txt for more detail.
-
-Example(da850 EVM ):
-nand_cs3@62000000 {
-        compatible = "ti,davinci-nand";
-        reg = <0x62000000 0x807ff
-                0x68000000 0x8000>;
-        ti,davinci-chipselect = <1>;
-        ti,davinci-mask-ale = <0>;
-        ti,davinci-mask-cle = <0>;
-        ti,davinci-mask-chipsel = <0>;
-        ti,davinci-ecc-mode = "hw";
-        ti,davinci-ecc-bits = <4>;
-        ti,davinci-nand-use-bbt;
-
-        partition@180000 {
-                label = "ubifs";
-                reg = <0x180000 0x7e80000>;
-        };
-};