serial/8250_hp300: Missing 8250 register interface conversion bits

commit 2655a2c76f80d91da34faa8f4e114d1793435ed3 ("8250: use the 8250
register interface not the legacy one") forgot to fully switch one
instance of struct uart_port to struct uart_8250_port, causing the
following compile failure:

drivers/tty/serial/8250/8250_hp300.c: In function ‘hpdca_init_one’:
drivers/tty/serial/8250/8250_hp300.c:174: error: ‘uart’ undeclared (first use in this function)
drivers/tty/serial/8250/8250_hp300.c:174: error: (Each undeclared identifier is reported only once
drivers/tty/serial/8250/8250_hp300.c:174: error: for each function it appears in.)

This went unnoticed in -next, as CONFIG_HPDCA is not set to y by
allmodconfig.

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Philip Blundell <philb@gnu.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1 files changed, 10 insertions, 10 deletions

diff --git a/drivers/tty/serial/8250/8250_hp300.c b/drivers/tty/serial/8250/8250_hp300.c
index 8f1dd2cc00a8..f3d0edf46644 100644
--- a/drivers/tty/serial/8250/8250_hp300.c
+++ b/drivers/tty/serial/8250/8250_hp300.c
@@ -162,7 +162,7 @@ int __init hp300_setup_serial_console(void)
 static int __devinit hpdca_init_one(struct dio_dev *d,
                                 const struct dio_device_id *ent)
 {
-        struct uart_port port;
+        struct uart_8250_port uart;
         int line;
 
 #ifdef CONFIG_SERIAL_8250_CONSOLE
@@ -174,19 +174,19 @@ static int __devinit hpdca_init_one(struct dio_dev *d,
         memset(&uart, 0, sizeof(uart));
 
         /* Memory mapped I/O */
-        port.iotype = UPIO_MEM;
-        port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF;
-        port.irq = d->ipl;
-        port.uartclk = HPDCA_BAUD_BASE * 16;
-        port.mapbase = (d->resource.start + UART_OFFSET);
-        port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
-        port.regshift = 1;
-        port.dev = &d->dev;
+        uart.port.iotype = UPIO_MEM;
+        uart.port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF;
+        uart.port.irq = d->ipl;
+        uart.port.uartclk = HPDCA_BAUD_BASE * 16;
+        uart.port.mapbase = (d->resource.start + UART_OFFSET);
+        uart.port.membase = (char *)(uart.port.mapbase + DIO_VIRADDRBASE);
+        uart.port.regshift = 1;
+        uart.port.dev = &d->dev;
         line = serial8250_register_8250_port(&uart);
 
         if (line < 0) {
                 printk(KERN_NOTICE "8250_hp300: register_serial() DCA scode %d"
-                       " irq %d failed\n", d->scode, port.irq);
+                       " irq %d failed\n", d->scode, uart.port.irq);
                 return -ENOMEM;
         }