#ifndef MFD_TMIO_H
#define MFD_TMIO_H
#include <linux/fb.h>
#include <linux/io.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#define tmio_ioread8(addr) readb(addr)
#define tmio_ioread16(addr) readw(addr)
#define tmio_ioread16_rep(r, b, l) readsw(r, b, l)
#define tmio_ioread32(addr) \
(((u32) readw((addr))) | (((u32) readw((addr) + 2)) << 16))
#define tmio_iowrite8(val, addr) writeb((val), (addr))
#define tmio_iowrite16(val, addr) writew((val), (addr))
#define tmio_iowrite16_rep(r, b, l) writesw(r, b, l)
#define tmio_iowrite32(val, addr) \
do { \
writew((val), (addr)); \
writew((val) >> 16, (addr) + 2); \
} while (0)
#define CNF_CMD 0x04
#define CNF_CTL_BASE 0x10
#define CNF_INT_PIN 0x3d
#define CNF_STOP_CLK_CTL 0x40
#define CNF_GCLK_CTL 0x41
#define CNF_SD_CLK_MODE 0x42
#define CNF_PIN_STATUS 0x44
#define CNF_PWR_CTL_1 0x48
#define CNF_PWR_CTL_2 0x49
#define CNF_PWR_CTL_3 0x4a
#define CNF_CARD_DETECT_MODE 0x4c
#define CNF_SD_SLOT 0x50
#define CNF_EXT_GCLK_CTL_1 0xf0
#define CNF_EXT_GCLK_CTL_2 0xf1
#define CNF_EXT_GCLK_CTL_3 0xf9
#define CNF_SD_LED_EN_1 0xfa
#define CNF_SD_LED_EN_2 0xfe
#define SDCREN 0x2 /* Enable access to MMC CTL regs. (flag in COMMAND_REG)*/
#define sd_config_write8(base, shift, reg, val) \
tmio_iowrite8((val), (base) + ((reg) << (shift)))
#define sd_config_write16(base, shift, reg, val) \
tmio_iowrite16((val), (base) + ((reg) << (shift)))
#define sd_config_write32(base, shift, reg, val) \
do { \
tmio_iowrite16((val), (base) + ((reg) << (shift))); \
tmio_iowrite16((val) >> 16, (base) + ((reg + 2) << (shift))); \
} while (0)
/* tmio MMC platform flags */
#define TMIO_MMC_WRPROTECT_DISABLE (1 << 0)
/*
* Some controllers can support a 2-byte block size when the bus width
* is configured in 4-bit mode.
*/
#define TMIO_MMC_BLKSZ_2BYTES (1 << 1)
/*
* Some controllers can support SDIO IRQ signalling.
*/
#define TMIO_MMC_SDIO_IRQ (1 << 2)
/*
* Some platforms can detect card insertion events with controller powered
* down, in which case they have to call tmio_mmc_cd_wakeup() to power up the
* controller and report the event to the driver.
*/
#define TMIO_MMC_HAS_COLD_CD (1 << 3)
int tmio_core_mmc_enable(void __iomem *cnf, int shift, unsigned long base);
int tmio_core_mmc_resume(void __iomem *cnf, int shift, unsigned long base);
void tmio_core_mmc_pwr(void __iomem *cnf, int shift, int state);
void tmio_core_mmc_clk_div(void __iomem *cnf, int shift, int state);
struct tmio_mmc_dma {
void *chan_priv_tx;
void *chan_priv_rx;
int alignment_shift;
};
/*
* data for the MMC controller
*/
struct tmio_mmc_data {
unsigned int hclk;
unsigned long capabilities;
unsigned long flags;
u32 ocr_mask; /* available voltages */
struct tmio_mmc_dma *dma;
struct device *dev;
bool power;
void (*set_pwr)(struct platform_device *host, int state);
void (*set_clk_div)(struct platform_device *host, int state);
int (*get_cd)(struct platform_device *host);
};
static inline void tmio_mmc_cd_wakeup(struct tmio_mmc_data *pdata)
{
if (pdata && !pdata->power) {
pdata->power = true;
pm_runtime_get(pdata->dev);
}
}
/*
* data for the NAND controller
*/
struct tmio_nand_data {
struct nand_bbt_descr *badblock_pattern;
struct mtd_partition *partition;
unsigned int num_partitions;
};
#define FBIO_TMIO_ACC_WRITE 0x7C639300
#define FBIO_TMIO_ACC_SYNC 0x7C639301
struct tmio_fb_data {
int (*lcd_set_power)(struct platform_device *fb_dev,
bool on);
int (*lcd_mode)(struct platform_device *fb_dev,
const struct fb_videomode *mode);
int num_modes;
struct fb_videomode *modes;
/* in mm: size of screen */
int height;
int width;
};
#endif
