#
# Video configuration
#
menu "Graphics support"
depends on HAS_IOMEM
source "drivers/char/agp/Kconfig"
source "drivers/gpu/drm/Kconfig"
config VGASTATE
tristate
default n
config VIDEO_OUTPUT_CONTROL
tristate "Lowlevel video output switch controls"
help
This framework adds support for low-level control of the video
output switch.
menuconfig FB
tristate "Support for frame buffer devices"
---help---
The frame buffer device provides an abstraction for the graphics
hardware. It represents the frame buffer of some video hardware and
allows application software to access the graphics hardware through
a well-defined interface, so the software doesn't need to know
anything about the low-level (hardware register) stuff.
Frame buffer devices work identically across the different
architectures supported by Linux and make the implementation of
application programs easier and more portable; at this point, an X
server exists which uses the frame buffer device exclusively.
On several non-X86 architectures, the frame buffer device is the
only way to use the graphics hardware.
The device is accessed through special device nodes, usually located
in the /dev directory, i.e. /dev/fb*.
You need an utility program called fbset to make full use of frame
buffer devices. Please read <file:Documentation/fb/framebuffer.txt>
and the Framebuffer-HOWTO at
<http://www.munted.org.uk/programming/Framebuffer-HOWTO-1.2.html> for more
information.
Say Y here and to the driver for your graphics board below if you
are compiling a kernel for a non-x86 architecture.
If you are compiling for the x86 architecture, you can say Y if you
want to play with it, but it is not essential. Please note that
running graphical applications that directly touch the hardware
(e.g. an accelerated X server) and that are not frame buffer
device-aware may cause unexpected results. If unsure, say N.
config FIRMWARE_EDID
bool "Enable firmware EDID"
depends on FB
default n
---help---
This enables access to the EDID transferred from the firmware.
On the i386, this is from the Video BIOS. Enable this if DDC/I2C
transfers do not work for your driver and if you are using
nvidiafb, i810fb or savagefb.
In general, choosing Y for this option is safe. If you
experience extremely long delays while booting before you get
something on your display, try setting this to N. Matrox cards in
combination with certain motherboards and monitors are known to
suffer from this problem.
config FB_DDC
tristate
depends on FB
select I2C_ALGOBIT
select I2C
default n
config FB_BOOT_VESA_SUPPORT
bool
depends on FB
default n
---help---
If true, at least one selected framebuffer driver can take advantage
of VESA video modes set at an early boot stage via the vga= parameter.
config FB_CFB_FILLRECT
tristate
depends on FB
default n
---help---
Include the cfb_fillrect function for generic software rectangle
filling. This is used by drivers that don't provide their own
(accelerated) version.
config FB_CFB_COPYAREA
tristate
depends on FB
default n
---help---
Include the cfb_copyarea function for generic software area copying.
This is used by drivers that don't provide their own (accelerated)
version.
config FB_CFB_IMAGEBLIT
tristate
depends on FB
default n
---help---
Include the cfb_imageblit function for generic software image
blitting. This is used by drivers that don't provide their own
(accelerated) version.
config FB_CFB_REV_PIXELS_IN_BYTE
bool
depends on FB
default n
---help---
Allow generic frame-buffer functions to work on displays with 1, 2
and 4 bits per pixel depths which has opposite order of pixels in
byte order to bytes in long order.
config FB_SYS_FILLRECT
tristate
depends on FB
default n
---help---
Include the sys_fillrect function for generic software rectangle
filling. This is used by drivers that don't provide their own
(accelerated) version and the framebuffer is in system RAM.
config FB_SYS_COPYAREA
tristate
depends on FB
default n
---help---
Include the sys_copyarea function for generic software area copying.
This is used by drivers that don't provide their own (accelerated)
version and the framebuffer is in system RAM.
config FB_SYS_IMAGEBLIT
tristate
depends on FB
default n
---help---
Include the sys_imageblit function for generic software image
blitting. This is used by drivers that don't provide their own
(accelerated) version and the framebuffer is in system RAM.
menuconfig FB_FOREIGN_ENDIAN
bool "Framebuffer foreign endianness support"
depends on FB
---help---
This menu will let you enable support for the framebuffers with
non-native endianness (e.g. Little-Endian framebuffer on a
Big-Endian machine). Most probably you don't have such hardware,
so it's safe to say "n" here.
choice
prompt "Choice endianness support"
depends on FB_FOREIGN_ENDIAN
config FB_BOTH_ENDIAN
bool "Support for Big- and Little-Endian framebuffers"
config FB_BIG_ENDIAN
bool "Support for Big-Endian framebuffers only"
config FB_LITTLE_ENDIAN
bool "Support for Little-Endian framebuffers only"
endchoice
config FB_SYS_FOPS
tristate
depends on FB
default n
config FB_DEFERRED_IO
bool
depends on FB
config FB_HECUBA
tristate
depends on FB
depends on FB_DEFERRED_IO
config FB_SVGALIB
tristate
depends on FB
default n
---help---
Common utility functions useful to fbdev drivers of VGA-based
cards.
config FB_MACMODES
tristate
depends on FB
default n
config FB_BACKLIGHT
bool
depends on FB
select BACKLIGHT_LCD_SUPPORT
select BACKLIGHT_CLASS_DEVICE
default n
config FB_MODE_HELPERS
bool "Enable Video Mode Handling Helpers"
depends on FB
default n
---help---
This enables functions for handling video modes using the
Generalized Timing Formula and the EDID parser. A few drivers rely
on this feature such as the radeonfb, rivafb, and the i810fb. If
your driver does not take advantage of this feature, choosing Y will
just increase the kernel size by about 5K.
config FB_TILEBLITTING
bool "Enable Tile Blitting Support"
depends on FB
default n
---help---
This enables tile blitting. Tile blitting is a drawing technique
where the screen is divided into rectangular sections (tiles), whereas
the standard blitting divides the screen into pixels. Because the
default drawing element is a tile, drawing functions will be passed
parameters in terms of number of tiles instead of number of pixels.
For example, to draw a single character, instead of using bitmaps,
an index to an array of bitmaps will be used. To clear or move a
rectangular section of a screen, the rectangle will be described in
terms of number of tiles in the x- and y-axis.
This is particularly important to one driver, matroxfb. If
unsure, say N.
comment "Frame buffer hardware drivers"
depends on FB
config FB_CIRRUS
tristate "Cirrus Logic support"
depends on FB && (ZORRO || PCI)
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
This enables support for Cirrus Logic GD542x/543x based boards on
Amiga: SD64, Piccolo, Picasso II/II+, Picasso IV, or EGS Spectrum.
If you have a PCI-based system, this enables support for these
chips: GD-543x, GD-544x, GD-5480.
Please read the file <file:Documentation/fb/cirrusfb.txt>.
Say N unless you have such a graphics board or plan to get one
before you next recompile the kernel.
config FB_PM2
tristate "Permedia2 support"
depends on FB && ((AMIGA && BROKEN) || PCI)
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for cards based on
the 3D Labs Permedia, Permedia 2 and Permedia 2V chips.
The driver was tested on the following cards:
Diamond FireGL 1000 PRO AGP
ELSA Gloria Synergy PCI
Appian Jeronimo PRO (both heads) PCI
3DLabs Oxygen ACX aka EONtronics Picasso P2 PCI
Techsource Raptor GFX-8P (aka Sun PGX-32) on SPARC
ASK Graphic Blaster Exxtreme AGP
To compile this driver as a module, choose M here: the
module will be called pm2fb.
config FB_PM2_FIFO_DISCONNECT
bool "enable FIFO disconnect feature"
depends on FB_PM2 && PCI
help
Support the Permedia2 FIFO disconnect feature.
config FB_ARMCLCD
tristate "ARM PrimeCell PL110 support"
depends on FB && ARM && ARM_AMBA
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This framebuffer device driver is for the ARM PrimeCell PL110
Colour LCD controller. ARM PrimeCells provide the building
blocks for System on a Chip devices.
If you want to compile this as a module (=code which can be
inserted into and removed from the running kernel), say M
here and read <file:Documentation/kbuild/modules.txt>. The module
will be called amba-clcd.
choice
depends on FB_ARMCLCD && (ARCH_LH7A40X || ARCH_LH7952X)
prompt "LCD Panel"
default FB_ARMCLCD_SHARP_LQ035Q7DB02
config FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
bool "LogicPD LCD 3.5\" QVGA w/HRTFT IC"
help
This is an implementation of the Sharp LQ035Q7DB02, a 3.5"
color QVGA, HRTFT panel. The LogicPD device includes
an integrated HRTFT controller IC.
The native resolution is 240x320.
config FB_ARMCLCD_SHARP_LQ057Q3DC02
bool "LogicPD LCD 5.7\" QVGA"
help
This is an implementation of the Sharp LQ057Q3DC02, a 5.7"
color QVGA, TFT panel. The LogicPD device includes an
The native resolution is 320x240.
config FB_ARMCLCD_SHARP_LQ64D343
bool "LogicPD LCD 6.4\" VGA"
help
This is an implementation of the Sharp LQ64D343, a 6.4"
color VGA, TFT panel. The LogicPD device includes an
The native resolution is 640x480.
config FB_ARMCLCD_SHARP_LQ10D368
bool "LogicPD LCD 10.4\" VGA"
help
This is an implementation of the Sharp LQ10D368, a 10.4"
color VGA, TFT panel. The LogicPD device includes an
The native resolution is 640x480.
config FB_ARMCLCD_SHARP_LQ121S1DG41
bool "LogicPD LCD 12.1\" SVGA"
help
This is an implementation of the Sharp LQ121S1DG41, a 12.1"
color SVGA, TFT panel. The LogicPD device includes an
The native resolution is 800x600.
This panel requires a clock rate may be an integer fraction
of the base LCDCLK frequency. The driver will select the
highest frequency available that is lower than the maximum
allowed. The panel may flicker if the clock rate is
slower than the recommended minimum.
config FB_ARMCLCD_AUO_A070VW01_WIDE
bool "AU Optronics A070VW01 LCD 7.0\" WIDE"
help
This is an implementation of the AU Optronics, a 7.0"
WIDE Color. The native resolution is 234x480.
config FB_ARMCLCD_HITACHI
bool "Hitachi Wide Screen 800x480"
help
This is an implementation of the Hitachi 800x480.
endchoice
config FB_ACORN
bool "Acorn VIDC support"
depends on (FB = y) && ARM && ARCH_ACORN
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the Acorn VIDC graphics
hardware found in Acorn RISC PCs and other ARM-based machines. If
unsure, say N.
config FB_CLPS711X
bool "CLPS711X LCD support"
depends on (FB = y) && ARM && ARCH_CLPS711X
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
Say Y to enable the Framebuffer driver for the CLPS7111 and
EP7212 processors.
config FB_SA1100
bool "SA-1100 LCD support"
depends on (FB = y) && ARM && ARCH_SA1100
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is a framebuffer device for the SA-1100 LCD Controller.
See <http://www.linux-fbdev.org/> for information on framebuffer
devices.
If you plan to use the LCD display with your SA-1100 system, say
Y here.
config FB_IMX
tristate "Motorola i.MX LCD support"
depends on FB && (ARCH_IMX || ARCH_MX2)
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
config FB_CYBER2000
tristate "CyberPro 2000/2010/5000 support"
depends on FB && PCI && (BROKEN || !SPARC64)
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This enables support for the Integraphics CyberPro 20x0 and 5000
VGA chips used in the Rebel.com Netwinder and other machines.
Say Y if you have a NetWinder or a graphics card containing this
device, otherwise say N.
config FB_APOLLO
bool
depends on (FB = y) && APOLLO
default y
select FB_CFB_FILLRECT
select FB_CFB_IMAGEBLIT
config FB_Q40
bool
depends on (FB = y) && Q40
default y
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
config FB_AMIGA
tristate "Amiga native chipset support"
depends on FB && AMIGA
help
This is the frame buffer device driver for the builtin graphics
chipset found in Amigas.
To compile this driver as a module, choose M here: the
module will be called amifb.
config FB_AMIGA_OCS
bool "Amiga OCS chipset support"
depends on FB_AMIGA
help
This enables support for the original Agnus and Denise video chips,
found in the Amiga 1000 and most A500's and A2000's. If you intend
to run Linux on any of these systems, say Y; otherwise say N.
config FB_AMIGA_ECS
bool "Amiga ECS chipset support"
depends on FB_AMIGA
help
This enables support for the Enhanced Chip Set, found in later
A500's, later A2000's, the A600, the A3000, the A3000T and CDTV. If
you intend to run Linux on any of these systems, say Y; otherwise
say N.
config FB_AMIGA_AGA
bool "Amiga AGA chipset support"
depends on FB_AMIGA
help
This enables support for the Advanced Graphics Architecture (also
known as the AGA or AA) Chip Set, found in the A1200, A4000, A4000T
and CD32. If you intend to run Linux on any of these systems, say Y;
otherwise say N.
config FB_FM2
bool "Amiga FrameMaster II/Rainbow II support"
depends on (FB = y) && ZORRO
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the Amiga FrameMaster
card from BSC (exhibited 1992 but not shipped as a CBM product).
config FB_ARC
tristate "Arc Monochrome LCD board support"
depends on FB && X86
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
select FB_SYS_FOPS
help
This enables support for the Arc Monochrome LCD board. The board
is based on the KS-108 lcd controller and is typically a matrix
of 2*n chips. This driver was tested with a 128x64 panel. This
driver supports it for use with x86 SBCs through a 16 bit GPIO
interface (8 bit data, 8 bit control). If you anticipate using
this driver, say Y or M; otherwise say N. You must specify the
GPIO IO address to be used for setting control and data.
config FB_ATARI
bool "Atari native chipset support"
depends on (FB = y) && ATARI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the builtin graphics
chipset found in Ataris.
config FB_OF
bool "Open Firmware frame buffer device support"
depends on (FB = y) && (PPC64 || PPC_OF) && (!PPC_PSERIES || PCI)
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_MACMODES
help
Say Y if you want support with Open Firmware for your graphics
board.
config FB_CONTROL
bool "Apple \"control\" display support"
depends on (FB = y) && PPC_PMAC && PPC32
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_MACMODES
help
This driver supports a frame buffer for the graphics adapter in the
Power Macintosh 7300 and others.
config FB_PLATINUM
bool "Apple \"platinum\" display support"
depends on (FB = y) && PPC_PMAC && PPC32
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_MACMODES
help
This driver supports a frame buffer for the "platinum" graphics
adapter in some Power Macintoshes.
config FB_VALKYRIE
bool "Apple \"valkyrie\" display support"
depends on (FB = y) && (MAC || (PPC_PMAC && PPC32))
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_MACMODES
help
This driver supports a frame buffer for the "valkyrie" graphics
adapter in some Power Macintoshes.
config FB_CT65550
bool "Chips 65550 display support"
depends on (FB = y) && PPC32 && PCI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the Chips & Technologies
65550 graphics chip in PowerBooks.
config FB_ASILIANT
bool "Asiliant (Chips) 69000 display support"
depends on (FB = y) && PCI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the Asiliant 69030 chipset
config FB_IMSTT
bool "IMS Twin Turbo display support"
depends on (FB = y) && PCI
select FB_CFB_IMAGEBLIT
select FB_MACMODES if PPC
help
The IMS Twin Turbo is a PCI-based frame buffer card bundled with
many Macintosh and compatible computers.
config FB_VGA16
tristate "VGA 16-color graphics support"
depends on FB && (X86 || PPC)
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select VGASTATE
select FONT_8x16 if FRAMEBUFFER_CONSOLE
help
This is the frame buffer device driver for VGA 16 color graphic
cards. Say Y if you have such a card.
To compile this driver as a module, choose M here: the
module will be called vga16fb.
config FB_BF54X_LQ043
tristate "SHARP LQ043 TFT LCD (BF548 EZKIT)"
depends on FB && (BF54x) && !BF542
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the framebuffer device driver for a SHARP LQ043T1DG01 TFT LCD
config FB_BFIN_T350MCQB
tristate "Varitronix COG-T350MCQB TFT LCD display (BF527 EZKIT)"
depends on FB && BLACKFIN
select BFIN_GPTIMERS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the framebuffer device driver for a Varitronix VL-PS-COG-T350MCQB-01 display TFT LCD
This display is a QVGA 320x240 24-bit RGB display interfaced by an 8-bit wide PPI
It uses PPI[0..7] PPI_FS1, PPI_FS2 and PPI_CLK.
config FB_STI
tristate "HP STI frame buffer device support"
depends on FB && PARISC
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
default y
---help---
STI refers to the HP "Standard Text Interface" which is a set of
BIOS routines contained in a ROM chip in HP PA-RISC based machines.
Enabling this option will implement the linux framebuffer device
using calls to the STI BIOS routines for initialisation.
If you enable this option, you will get a planar framebuffer device
/dev/fb which will work on the most common HP graphic cards of the
NGLE family, including the artist chips (in the 7xx and Bxxx series),
HCRX, HCRX24, CRX, CRX24 and VisEG series.
It is safe to enable this option, so you should probably say "Y".
config FB_MAC
bool "Generic Macintosh display support"
depends on (FB = y) && MAC
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_MACMODES
config FB_HP300
bool
depends on (FB = y) && DIO
select FB_CFB_IMAGEBLIT
default y
config FB_TGA
tristate "TGA/SFB+ framebuffer support"
depends on FB && (ALPHA || TC)
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select BITREVERSE
---help---
This is the frame buffer device driver for generic TGA and SFB+
graphic cards. These include DEC ZLXp-E1, -E2 and -E3 PCI cards,
also known as PBXGA-A, -B and -C, and DEC ZLX-E1, -E2 and -E3
TURBOchannel cards, also known as PMAGD-A, -B and -C.
Due to hardware limitations ZLX-E2 and E3 cards are not supported
for DECstation 5000/200 systems. Additionally due to firmware
limitations these cards may cause troubles with booting DECstation
5000/240 and /260 systems, but are fully supported under Linux if
you manage to get it going. ;-)
Say Y if you have one of those.
config FB_UVESA
tristate "Userspace VESA VGA graphics support"
depends on FB && CONNECTOR
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_MODE_HELPERS
help
This is the frame buffer driver for generic VBE 2.0 compliant
graphic cards. It can also take advantage of VBE 3.0 features,
such as refresh rate adjustment.
This driver generally provides more features than vesafb but
requires a userspace helper application called 'v86d'. See
<file:Documentation/fb/uvesafb.txt> for more information.
If unsure, say N.
config FB_VESA
bool "VESA VGA graphics support"
depends on (FB = y) && X86
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_BOOT_VESA_SUPPORT
help
This is the frame buffer device driver for generic VESA 2.0
compliant graphic cards. The older VESA 1.2 cards are not supported.
You will get a boot time penguin logo at no additional cost. Please
read <file:Documentation/fb/vesafb.txt>. If unsure, say Y.
config FB_EFI
bool "EFI-based Framebuffer Support"
depends on (FB = y) && X86 && EFI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the EFI frame buffer device driver. If the firmware on
your platform is EFI 1.10 or UEFI 2.0, select Y to add support for
using the EFI framebuffer as your console.
config FB_N411
tristate "N411 Apollo/Hecuba devkit support"
depends on FB && X86 && MMU
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
select FB_SYS_FOPS
select FB_DEFERRED_IO
select FB_HECUBA
help
This enables support for the Apollo display controller in its
Hecuba form using the n411 devkit.
config FB_HGA
tristate "Hercules mono graphics support"
depends on FB && X86
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
Say Y here if you have a Hercules mono graphics card.
To compile this driver as a module, choose M here: the
module will be called hgafb.
As this card technology is 15 years old, most people will answer N
here.
config FB_HGA_ACCEL
bool "Hercules mono Acceleration functions (EXPERIMENTAL)"
depends on FB_HGA && EXPERIMENTAL
---help---
This will compile the Hercules mono graphics with
acceleration functions.
config FB_SGIVW
tristate "SGI Visual Workstation framebuffer support"
depends on FB && X86_VISWS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
SGI Visual Workstation support for framebuffer graphics.
config FB_GBE
bool "SGI Graphics Backend frame buffer support"
depends on (FB = y) && (SGI_IP32 || X86_VISWS)
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for SGI Graphics Backend.
This chip is used in SGI O2 and Visual Workstation 320/540.
config FB_GBE_MEM
int "Video memory size in MB"
depends on FB_GBE
default 4
help
This is the amount of memory reserved for the framebuffer,
which can be any value between 1MB and 8MB.
config FB_SBUS
bool "SBUS and UPA framebuffers"
depends on (FB = y) && SPARC
help
Say Y if you want support for SBUS or UPA based frame buffer device.
config FB_BW2
bool "BWtwo support"
depends on (FB = y) && (SPARC && FB_SBUS)
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the BWtwo frame buffer.
config FB_CG3
bool "CGthree support"
depends on (FB = y) && (SPARC && FB_SBUS)
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the CGthree frame buffer.
config FB_CG6
bool "CGsix (GX,TurboGX) support"
depends on (FB = y) && (SPARC && FB_SBUS)
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the CGsix (GX, TurboGX)
frame buffer.
config FB_FFB
bool "Creator/Creator3D/Elite3D support"
depends on FB_SBUS && SPARC64
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the Creator, Creator3D,
and Elite3D graphics boards.
config FB_TCX
bool "TCX (SS4/SS5 only) support"
depends on FB_SBUS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the TCX 24/8bit frame
buffer.
config FB_CG14
bool "CGfourteen (SX) support"
depends on FB_SBUS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the CGfourteen frame
buffer on Desktop SPARCsystems with the SX graphics option.
config FB_P9100
bool "P9100 (Sparcbook 3 only) support"
depends on FB_SBUS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the P9100 card
supported on Sparcbook 3 machines.
config FB_LEO
bool "Leo (ZX) support"
depends on FB_SBUS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the SBUS-based Sun ZX
(leo) frame buffer cards.
config FB_IGA
bool "IGA 168x display support"
depends on (FB = y) && SPARC32
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the framebuffer device for the INTERGRAPHICS 1680 and
successor frame buffer cards.
config FB_XVR500
bool "Sun XVR-500 3DLABS Wildcat support"
depends on (FB = y) && PCI && SPARC64
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the framebuffer device for the Sun XVR-500 and similar
graphics cards based upon the 3DLABS Wildcat chipset. The driver
only works on sparc64 systems where the system firmware has
mostly initialized the card already. It is treated as a
completely dumb framebuffer device.
config FB_XVR2500
bool "Sun XVR-2500 3DLABS Wildcat support"
depends on (FB = y) && PCI && SPARC64
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the framebuffer device for the Sun XVR-2500 and similar
graphics cards based upon the 3DLABS Wildcat chipset. The driver
only works on sparc64 systems where the system firmware has
mostly initialized the card already. It is treated as a
completely dumb framebuffer device.
config FB_PVR2
tristate "NEC PowerVR 2 display support"
depends on FB && SH_DREAMCAST
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
Say Y here if you have a PowerVR 2 card in your box. If you plan to
run linux on your Dreamcast, you will have to say Y here.
This driver may or may not work on other PowerVR 2 cards, but is
totally untested. Use at your own risk. If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called pvr2fb.
You can pass several parameters to the driver at boot time or at
module load time. The parameters look like "video=pvr2:XXX", where
the meaning of XXX can be found at the end of the main source file
(<file:drivers/video/pvr2fb.c>). Please see the file
<file:Documentation/fb/pvr2fb.txt>.
config FB_EPSON1355
bool "Epson 1355 framebuffer support"
depends on (FB = y) && ARCH_CEIVA
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
Build in support for the SED1355 Epson Research Embedded RAMDAC
LCD/CRT Controller (since redesignated as the S1D13505) as a
framebuffer. Product specs at
<http://www.erd.epson.com/vdc/html/products.htm>.
config FB_S1D13XXX
tristate "Epson S1D13XXX framebuffer support"
depends on FB
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
Support for S1D13XXX framebuffer device family (currently only
working with S1D13806). Product specs at
<http://www.erd.epson.com/vdc/html/legacy_13xxx.htm>
config FB_ATMEL
tristate "AT91/AT32 LCD Controller support"
depends on FB && (ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || AVR32)
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This enables support for the AT91/AT32 LCD Controller.
config FB_INTSRAM
bool "Frame Buffer in internal SRAM"
depends on FB_ATMEL && ARCH_AT91SAM9261
help
Say Y if you want to map Frame Buffer in internal SRAM. Say N if you want
to let frame buffer in external SDRAM.
config FB_ATMEL_STN
bool "Use a STN display with AT91/AT32 LCD Controller"
depends on FB_ATMEL && MACH_AT91SAM9261EK
default n
help
Say Y if you want to connect a STN LCD display to the AT91/AT32 LCD
Controller. Say N if you want to connect a TFT.
If unsure, say N.
config FB_NVIDIA
tristate "nVidia Framebuffer Support"
depends on FB && PCI
select FB_BACKLIGHT if FB_NVIDIA_BACKLIGHT
select FB_MODE_HELPERS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select BITREVERSE
select VGASTATE
help
This driver supports graphics boards with the nVidia chips, TNT
and newer. For very old chipsets, such as the RIVA128, then use
the rivafb.
Say Y if you have such a graphics board.
To compile this driver as a module, choose M here: the
module will be called nvidiafb.
config FB_NVIDIA_I2C
bool "Enable DDC Support"
depends on FB_NVIDIA
select FB_DDC
help
This enables I2C support for nVidia Chipsets. This is used
only for getting EDID information from the attached display
allowing for robust video mode handling and switching.
Because fbdev-2.6 requires that drivers must be able to
independently validate video mode parameters, you should say Y
here.
config FB_NVIDIA_DEBUG
bool "Lots of debug output"
depends on FB_NVIDIA
default n
help
Say Y here if you want the nVidia driver to output all sorts
of debugging information to provide to the maintainer when
something goes wrong.
config FB_NVIDIA_BACKLIGHT
bool "Support for backlight control"
depends on FB_NVIDIA
default y
help
Say Y here if you want to control the backlight of your display.
config FB_RIVA
tristate "nVidia Riva support"
depends on FB && PCI
select FB_BACKLIGHT if FB_RIVA_BACKLIGHT
select FB_MODE_HELPERS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select BITREVERSE
select VGASTATE
help
This driver supports graphics boards with the nVidia Riva/Geforce
chips.
Say Y if you have such a graphics board.
To compile this driver as a module, choose M here: the
module will be called rivafb.
config FB_RIVA_I2C
bool "Enable DDC Support"
depends on FB_RIVA
select FB_DDC
help
This enables I2C support for nVidia Chipsets. This is used
only for getting EDID information from the attached display
allowing for robust video mode handling and switching.
Because fbdev-2.6 requires that drivers must be able to
independently validate video mode parameters, you should say Y
here.
config FB_RIVA_DEBUG
bool "Lots of debug output"
depends on FB_RIVA
default n
help
Say Y here if you want the Riva driver to output all sorts
of debugging information to provide to the maintainer when
something goes wrong.
config FB_RIVA_BACKLIGHT
bool "Support for backlight control"
depends on FB_RIVA
default y
help
Say Y here if you want to control the backlight of your display.
config FB_I810
tristate "Intel 810/815 support (EXPERIMENTAL)"
depends on EXPERIMENTAL && FB && PCI && X86_32 && AGP_INTEL
select FB_MODE_HELPERS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select VGASTATE
help
This driver supports the on-board graphics built in to the Intel 810
and 815 chipsets. Say Y if you have and plan to use such a board.
To compile this driver as a module, choose M here: the
module will be called i810fb.
For more information, please read
<file:Documentation/fb/intel810.txt>
config FB_I810_GTF
bool "use VESA Generalized Timing Formula"
depends on FB_I810
help
If you say Y, then the VESA standard, Generalized Timing Formula
or GTF, will be used to calculate the required video timing values
per video mode. Since the GTF allows nondiscrete timings
(nondiscrete being a range of values as opposed to discrete being a
set of values), you'll be able to use any combination of horizontal
and vertical resolutions, and vertical refresh rates without having
to specify your own timing parameters. This is especially useful
to maximize the performance of an aging display, or if you just
have a display with nonstandard dimensions. A VESA compliant
monitor is recommended, but can still work with non-compliant ones.
If you need or want this, then select this option. The timings may
not be compliant with Intel's recommended values. Use at your own
risk.
If you say N, the driver will revert to discrete video timings
using a set recommended by Intel in their documentation.
If unsure, say N.
config FB_I810_I2C
bool "Enable DDC Support"
depends on FB_I810 && FB_I810_GTF
select FB_DDC
help
config FB_LE80578
tristate "Intel LE80578 (Vermilion) support"
depends on FB && PCI && X86
select FB_MODE_HELPERS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This driver supports the LE80578 (Vermilion Range) chipset
config FB_CARILLO_RANCH
tristate "Intel Carillo Ranch support"
depends on FB_LE80578 && FB && PCI && X86
help
This driver supports the LE80578 (Carillo Ranch) board
config FB_INTEL
tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G/945GM/965G/965GM support (EXPERIMENTAL)"
depends on EXPERIMENTAL && FB && PCI && X86 && AGP_INTEL
select FB_MODE_HELPERS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_BOOT_VESA_SUPPORT
help
This driver supports the on-board graphics built in to the Intel
830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets.
Say Y if you have and plan to use such a board.
To compile this driver as a module, choose M here: the
module will be called intelfb.
For more information, please read <file:Documentation/fb/intelfb.txt>
config FB_INTEL_DEBUG
bool "Intel driver Debug Messages"
depends on FB_INTEL
---help---
Say Y here if you want the Intel driver to output all sorts
of debugging information to provide to the maintainer when
something goes wrong.
config FB_INTEL_I2C
bool "DDC/I2C for Intel framebuffer support"
depends on FB_INTEL
select FB_DDC
default y
help
Say Y here if you want DDC/I2C support for your on-board Intel graphics.
config FB_MATROX
tristate "Matrox acceleration"
depends on FB && PCI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_TILEBLITTING
select FB_MACMODES if PPC_PMAC
---help---
Say Y here if you have a Matrox Millennium, Matrox Millennium II,
Matrox Mystique, Matrox Mystique 220, Matrox Productiva G100, Matrox
Mystique G200, Matrox Millennium G200, Matrox Marvel G200 video,
Matrox G400, G450 or G550 card in your box.
To compile this driver as a module, choose M here: the
module will be called matroxfb.
You can pass several parameters to the driver at boot time or at
module load time. The parameters look like "video=matrox:XXX", and
are described in <file:Documentation/fb/matroxfb.txt>.
config FB_MATROX_MILLENIUM
bool "Millennium I/II support"
depends on FB_MATROX
help
Say Y here if you have a Matrox Millennium or Matrox Millennium II
video card. If you select "Advanced lowlevel driver options" below,
you should check 4 bpp packed pixel, 8 bpp packed pixel, 16 bpp
packed pixel, 24 bpp packed pixel and 32 bpp packed pixel. You can
also use font widths different from 8.
config FB_MATROX_MYSTIQUE
bool "Mystique support"
depends on FB_MATROX
help
Say Y here if you have a Matrox Mystique or Matrox Mystique 220
video card. If you select "Advanced lowlevel driver options" below,
you should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp
packed pixel and 32 bpp packed pixel. You can also use font widths
different from 8.
config FB_MATROX_G
bool "G100/G200/G400/G450/G550 support"
depends on FB_MATROX
---help---
Say Y here if you have a Matrox G100, G200, G400, G450 or G550 based
video card. If you select "Advanced lowlevel driver options", you
should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed
pixel and 32 bpp packed pixel. You can also use font widths
different from 8.
If you need support for G400 secondary head, you must say Y to
"Matrox I2C support" and "G400 second head support" right below.
G450/G550 secondary head and digital output are supported without
additional modules.
The driver starts in monitor mode. You must use the matroxset tool
(available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to
swap primary and secondary head outputs, or to change output mode.
Secondary head driver always start in 640x480 resolution and you
must use fbset to change it.
Do not forget that second head supports only 16 and 32 bpp
packed pixels, so it is a good idea to compile them into the kernel
too. You can use only some font widths, as the driver uses generic
painting procedures (the secondary head does not use acceleration
engine).
G450/G550 hardware can display TV picture only from secondary CRTC,
and it performs no scaling, so picture must have 525 or 625 lines.
config FB_MATROX_I2C
tristate "Matrox I2C support"
depends on FB_MATROX
select FB_DDC
---help---
This drivers creates I2C buses which are needed for accessing the
DDC (I2C) bus present on all Matroxes, an I2C bus which
interconnects Matrox optional devices, like MGA-TVO on G200 and
G400, and the secondary head DDC bus, present on G400 only.
You can say Y or M here if you want to experiment with monitor
detection code. You must say Y or M here if you want to use either
second head of G400 or MGA-TVO on G200 or G400.
If you compile it as module, it will create a module named
i2c-matroxfb.
config FB_MATROX_MAVEN
tristate "G400 second head support"
depends on FB_MATROX_G && FB_MATROX_I2C
---help---
WARNING !!! This support does not work with G450 !!!
Say Y or M here if you want to use a secondary head (meaning two
monitors in parallel) on G400 or MGA-TVO add-on on G200. Secondary
head is not compatible with accelerated XFree 3.3.x SVGA servers -
secondary head output is blanked while you are in X. With XFree
3.9.17 preview you can use both heads if you use SVGA over fbdev or
the fbdev driver on first head and the fbdev driver on second head.
If you compile it as module, two modules are created,
matroxfb_crtc2 and matroxfb_maven. Matroxfb_maven is needed for
both G200 and G400, matroxfb_crtc2 is needed only by G400. You must
also load i2c-matroxfb to get it to run.
The driver starts in monitor mode and you must use the matroxset
tool (available at
<ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to switch it to
PAL or NTSC or to swap primary and secondary head outputs.
Secondary head driver also always start in 640x480 resolution, you
must use fbset to change it.
Also do not forget that second head supports only 16 and 32 bpp
packed pixels, so it is a good idea to compile them into the kernel
too. You can use only some font widths, as the driver uses generic
painting procedures (the secondary head does not use acceleration
engine).
config FB_MATROX_MULTIHEAD
bool "Multihead support"
depends on FB_MATROX
---help---
Say Y here if you have more than one (supported) Matrox device in
your computer and you want to use all of them for different monitors
("multihead"). If you have only one device, you should say N because
the driver compiled with Y is larger and a bit slower, especially on
ia32 (ix86).
If you said M to "Matrox unified accelerated driver" and N here, you
will still be able to use several Matrox devices simultaneously:
insert several instances of the module matroxfb into the kernel
with insmod, supplying the parameter "dev=N" where N is 0, 1, etc.
for the different Matrox devices. This method is slightly faster but
uses 40 KB of kernel memory per Matrox card.
There is no need for enabling 'Matrox multihead support' if you have
only one Matrox card in the box.
config FB_RADEON
tristate "ATI Radeon display support"
depends on FB && PCI
select FB_BACKLIGHT if FB_RADEON_BACKLIGHT
select FB_MODE_HELPERS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_MACMODES if PPC_OF
help
Choose this option if you want to use an ATI Radeon graphics card as
a framebuffer device. There are both PCI and AGP versions. You
don't need to choose this to run the Radeon in plain VGA mode.
There is a product page at
http://apps.ati.com/ATIcompare/
config FB_RADEON_I2C
bool "DDC/I2C for ATI Radeon support"
depends on FB_RADEON
select FB_DDC
default y
help
Say Y here if you want DDC/I2C support for your Radeon board.
config FB_RADEON_BACKLIGHT
bool "Support for backlight control"
depends on FB_RADEON
default y
help
Say Y here if you want to control the backlight of your display.
config FB_RADEON_DEBUG
bool "Lots of debug output from Radeon driver"
depends on FB_RADEON
default n
help
Say Y here if you want the Radeon driver to output all sorts
of debugging information to provide to the maintainer when
something goes wrong.
config FB_ATY128
tristate "ATI Rage128 display support"
depends on FB && PCI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_BACKLIGHT if FB_ATY128_BACKLIGHT
select FB_MACMODES if PPC_PMAC
help
This driver supports graphics boards with the ATI Rage128 chips.
Say Y if you have such a graphics board and read
<file:Documentation/fb/aty128fb.txt>.
To compile this driver as a module, choose M here: the
module will be called aty128fb.
config FB_ATY128_BACKLIGHT
bool "Support for backlight control"
depends on FB_ATY128
default y
help
Say Y here if you want to control the backlight of your display.
config FB_ATY
tristate "ATI Mach64 display support" if PCI || ATARI
depends on FB && !SPARC32
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_BACKLIGHT if FB_ATY_BACKLIGHT
select FB_MACMODES if PPC
help
This driver supports graphics boards with the ATI Mach64 chips.
Say Y if you have such a graphics board.
To compile this driver as a module, choose M here: the
module will be called atyfb.
config FB_ATY_CT
bool "Mach64 CT/VT/GT/LT (incl. 3D RAGE) support"
depends on PCI && FB_ATY
default y if SPARC64 && PCI
help
Say Y here to support use of ATI's 64-bit Rage boards (or other
boards based on the Mach64 CT, VT, GT, and LT chipsets) as a
framebuffer device. The ATI product support page for these boards
is at <http://support.ati.com/products/pc/mach64/>.
config FB_ATY_GENERIC_LCD
bool "Mach64 generic LCD support (EXPERIMENTAL)"
depends on FB_ATY_CT
help
Say Y if you have a laptop with an ATI Rage LT PRO, Rage Mobility,
Rage XC, or Rage XL chipset.
config FB_ATY_GX
bool "Mach64 GX support" if PCI
depends on FB_ATY
default y if ATARI
help
Say Y here to support use of the ATI Mach64 Graphics Expression
board (or other boards based on the Mach64 GX chipset) as a
framebuffer device. The ATI product support page for these boards
is at
<http://support.ati.com/products/pc/mach64/graphics_xpression.html>.
config FB_ATY_BACKLIGHT
bool "Support for backlight control"
depends on FB_ATY
default y
help
Say Y here if you want to control the backlight of your display.
config FB_S3
tristate "S3 Trio/Virge support"
depends on FB && PCI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_TILEBLITTING
select FB_SVGALIB
select VGASTATE
select FONT_8x16 if FRAMEBUFFER_CONSOLE
---help---
Driver for graphics boards with S3 Trio / S3 Virge chip.
config FB_SAVAGE
tristate "S3 Savage support"
depends on FB && PCI && EXPERIMENTAL
select FB_MODE_HELPERS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select VGASTATE
help
This driver supports notebooks and computers with S3 Savage PCI/AGP
chips.
Say Y if you have such a graphics card.
To compile this driver as a module, choose M here; the module
will be called savagefb.
config FB_SAVAGE_I2C
bool "Enable DDC2 Support"
depends on FB_SAVAGE
select FB_DDC
help
This enables I2C support for S3 Savage Chipsets. This is used
only for getting EDID information from the attached display
allowing for robust video mode handling and switching.
Because fbdev-2.6 requires that drivers must be able to
independently validate video mode parameters, you should say Y
here.
config FB_SAVAGE_ACCEL
bool "Enable Console Acceleration"
depends on FB_SAVAGE
default n
help
This option will compile in console acceleration support. If
the resulting framebuffer console has bothersome glitches, then
choose N here.
config FB_SIS
tristate "SiS/XGI display support"
depends on FB && PCI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_BOOT_VESA_SUPPORT
help
This is the frame buffer device driver for the SiS 300, 315, 330
and 340 series as well as XGI V3XT, V5, V8, Z7 graphics chipsets.
Specs available at <http://www.sis.com> and <http://www.xgitech.com>.
To compile this driver as a module, choose M here; the module
will be called sisfb.
config FB_SIS_300
bool "SiS 300 series support"
depends on FB_SIS
help
Say Y here to support use of the SiS 300/305, 540, 630 and 730.
config FB_SIS_315
bool "SiS 315/330/340 series and XGI support"
depends on FB_SIS
help
Say Y here to support use of the SiS 315, 330 and 340 series
(315/H/PRO, 55x, 650, 651, 740, 330, 661, 741, 760, 761) as well
as XGI V3XT, V5, V8 and Z7.
config FB_VIA
tristate "VIA UniChrome (Pro) and Chrome9 display support"
depends on FB && PCI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_SOFT_CURSOR
select I2C_ALGOBIT
select I2C
help
This is the frame buffer device driver for Graphics chips of VIA
UniChrome (Pro) Family (CLE266,PM800/CN400,P4M800CE/P4M800Pro/
CN700/VN800,CX700/VX700,P4M890) and Chrome9 Family (K8M890,CN896
/P4M900,VX800)
Say Y if you have a VIA UniChrome graphics board.
To compile this driver as a module, choose M here: the
module will be called viafb.
config FB_NEOMAGIC
tristate "NeoMagic display support"
depends on FB && PCI
select FB_MODE_HELPERS
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select VGASTATE
help
This driver supports notebooks with NeoMagic PCI chips.
Say Y if you have such a graphics card.
To compile this driver as a module, choose M here: the
module will be called neofb.
config FB_KYRO
tristate "IMG Kyro support"
depends on FB && PCI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
Say Y here if you have a STG4000 / Kyro / PowerVR 3 based
graphics board.
To compile this driver as a module, choose M here: the
module will be called kyrofb.
config FB_3DFX
tristate "3Dfx Banshee/Voodoo3/Voodoo5 display support"
depends on FB && PCI
select FB_CFB_IMAGEBLIT
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_MODE_HELPERS
help
This driver supports graphics boards with the 3Dfx Banshee,
Voodoo3 or VSA-100 (aka Voodoo4/5) chips. Say Y if you have
such a graphics board.
To compile this driver as a module, choose M here: the
module will be called tdfxfb.
config FB_3DFX_ACCEL
bool "3Dfx Acceleration functions (EXPERIMENTAL)"
depends on FB_3DFX && EXPERIMENTAL
---help---
This will compile the 3Dfx Banshee/Voodoo3/VSA-100 frame buffer
device driver with acceleration functions.
config FB_3DFX_I2C
bool "Enable DDC/I2C support"
depends on FB_3DFX && EXPERIMENTAL
select FB_DDC
default y
help
Say Y here if you want DDC/I2C support for your 3dfx Voodoo3.
config FB_VOODOO1
tristate "3Dfx Voodoo Graphics (sst1) support"
depends on FB && PCI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
Say Y here if you have a 3Dfx Voodoo Graphics (Voodoo1/sst1) or
Voodoo2 (cvg) based graphics card.
To compile this driver as a module, choose M here: the
module will be called sstfb.
WARNING: Do not use any application that uses the 3D engine
(namely glide) while using this driver.
Please read the <file:Documentation/fb/sstfb.txt> for supported
options and other important info support.
config FB_VT8623
tristate "VIA VT8623 support"
depends on FB && PCI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_TILEBLITTING
select FB_SVGALIB
select VGASTATE
select FONT_8x16 if FRAMEBUFFER_CONSOLE
---help---
Driver for CastleRock integrated graphics core in the
VIA VT8623 [Apollo CLE266] chipset.
config FB_TRIDENT
tristate "Trident/CyberXXX/CyberBlade support"
depends on FB && PCI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
This is the frame buffer device driver for Trident PCI/AGP chipsets.
Supported chipset families are TGUI 9440/96XX, 3DImage, Blade3D
and Blade XP.
There are also integrated versions of these chips called CyberXXXX,
CyberImage or CyberBlade. These chips are mostly found in laptops
but also on some motherboards including early VIA EPIA motherboards.
For more information, read <file:Documentation/fb/tridentfb.txt>
Say Y if you have such a graphics board.
To compile this driver as a module, choose M here: the
module will be called tridentfb.
config FB_ARK
tristate "ARK 2000PV support"
depends on FB && PCI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_TILEBLITTING
select FB_SVGALIB
select VGASTATE
select FONT_8x16 if FRAMEBUFFER_CONSOLE
---help---
Driver for PCI graphics boards with ARK 2000PV chip
and ICS 5342 RAMDAC.
config FB_PM3
tristate "Permedia3 support (EXPERIMENTAL)"
depends on FB && PCI && EXPERIMENTAL
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the 3DLabs Permedia3
chipset, used in Formac ProFormance III, 3DLabs Oxygen VX1 &
similar boards, 3DLabs Permedia3 Create!, Appian Jeronimo 2000
and maybe other boards.
config FB_CARMINE
tristate "Fujitsu carmine frame buffer support"
depends on FB && PCI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the Fujitsu Carmine chip.
The driver provides two independent frame buffer devices.
choice
depends on FB_CARMINE
prompt "DRAM timing"
default FB_CARMINE_DRAM_EVAL
config FB_CARMINE_DRAM_EVAL
bool "Eval board timings"
help
Use timings which work on the eval card.
config CARMINE_DRAM_CUSTOM
bool "Custom board timings"
help
Use custom board timings.
endchoice
config FB_AU1100
bool "Au1100 LCD Driver"
depends on (FB = y) && MIPS && SOC_AU1100
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the framebuffer driver for the AMD Au1100 SOC. It can drive
various panels and CRTs by passing in kernel cmd line option
au1100fb:panel=<name>.
config FB_AU1200
bool "Au1200 LCD Driver"
depends on (FB = y) && MIPS && SOC_AU1200
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the framebuffer driver for the AMD Au1200 SOC. It can drive
various panels and CRTs by passing in kernel cmd line option
au1200fb:panel=<name>.
source "drivers/video/geode/Kconfig"
config FB_HIT
tristate "HD64461 Frame Buffer support"
depends on FB && HD64461
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This is the frame buffer device driver for the Hitachi HD64461 LCD
frame buffer card.
config FB_PMAG_AA
bool "PMAG-AA TURBOchannel framebuffer support"
depends on (FB = y) && TC
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
Support for the PMAG-AA TURBOchannel framebuffer card (1280x1024x1)
used mainly in the MIPS-based DECstation series.
config FB_PMAG_BA
tristate "PMAG-BA TURBOchannel framebuffer support"
depends on FB && TC
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
Support for the PMAG-BA TURBOchannel framebuffer card (1024x864x8)
used mainly in the MIPS-based DECstation series.
config FB_PMAGB_B
tristate "PMAGB-B TURBOchannel framebuffer support"
depends on FB && TC
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
Support for the PMAGB-B TURBOchannel framebuffer card used mainly
in the MIPS-based DECstation series. The card is currently only
supported in 1280x1024x8 mode.
config FB_MAXINE
bool "Maxine (Personal DECstation) onboard framebuffer support"
depends on (FB = y) && MACH_DECSTATION
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
Support for the onboard framebuffer (1024x768x8) in the Personal
DECstation series (Personal DECstation 5000/20, /25, /33, /50,
Codename "Maxine").
config FB_G364
bool "G364 frame buffer support"
depends on (FB = y) && (MIPS_MAGNUM_4000 || OLIVETTI_M700)
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
The G364 driver is the framebuffer used in MIPS Magnum 4000 and
Olivetti M700-10 systems.
config FB_68328
bool "Motorola 68328 native frame buffer support"
depends on (FB = y) && (M68328 || M68EZ328 || M68VZ328)
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
Say Y here if you want to support the built-in frame buffer of
the Motorola 68328 CPU family.
config FB_PXA
tristate "PXA LCD framebuffer support"
depends on FB && ARCH_PXA
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
Frame buffer driver for the built-in LCD controller in the Intel
PXA2x0 processor.
This driver is also available as a module ( = code which can be
inserted and removed from the running kernel whenever you want). The
module will be called pxafb. If you want to compile it as a module,
say M here and read <file:Documentation/kbuild/modules.txt>.
If unsure, say N.
config FB_PXA_OVERLAY
bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer"
default n
depends on FB_PXA && (PXA27x || PXA3xx)
config FB_PXA_SMARTPANEL
bool "PXA Smartpanel LCD support"
default n
depends on FB_PXA
config FB_PXA_PARAMETERS
bool "PXA LCD command line parameters"
default n
depends on FB_PXA
---help---
Enable the use of kernel command line or module parameters
to configure the physical properties of the LCD panel when
using the PXA LCD driver.
This option allows you to override the panel parameters
supplied by the platform in order to support multiple
different models of flatpanel. If you will only be using a
single model of flatpanel then you can safely leave this
option disabled.
<file:Documentation/fb/pxafb.txt> describes the available parameters.
config FB_MBX
tristate "2700G LCD framebuffer support"
depends on FB && ARCH_PXA
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
Framebuffer driver for the Intel 2700G (Marathon) Graphics
Accelerator
config FB_MBX_DEBUG
bool "Enable debugging info via debugfs"
depends on FB_MBX && DEBUG_FS
default n
---help---
Enable this if you want debugging information using the debug
filesystem (debugfs)
If unsure, say N.
config FB_FSL_DIU
tristate "Freescale DIU framebuffer support"
depends on FB && FSL_SOC
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select PPC_LIB_RHEAP
---help---
Framebuffer driver for the Freescale SoC DIU
config FB_W100
tristate "W100 frame buffer support"
depends on FB && ARCH_PXA
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
Frame buffer driver for the w100 as found on the Sharp SL-Cxx series.
It can also drive the w3220 chip found on iPAQ hx4700.
This driver is also available as a module ( = code which can be
inserted and removed from the running kernel whenever you want). The
module will be called w100fb. If you want to compile it as a module,
say M here and read <file:Documentation/kbuild/modules.txt>.
If unsure, say N.
config FB_SH_MOBILE_LCDC
tristate "SuperH Mobile LCDC framebuffer support"
depends on FB && SUPERH
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
select FB_SYS_FOPS
select FB_DEFERRED_IO
---help---
Frame buffer driver for the on-chip SH-Mobile LCD controller.
config FB_TMIO
tristate "Toshiba Mobile IO FrameBuffer support"
depends on FB && MFD_CORE
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
Frame buffer driver for the Toshiba Mobile IO integrated as found
on the Sharp SL-6000 series
This driver is also available as a module ( = code which can be
inserted and removed from the running kernel whenever you want). The
module will be called tmiofb. If you want to compile it as a module,
say M here and read <file:Documentation/kbuild/modules.txt>.
If unsure, say N.
config FB_TMIO_ACCELL
bool "tmiofb acceleration"
depends on FB_TMIO
default y
config FB_S3C
tristate "Samsung S3C framebuffer support"
depends on FB && ARCH_S3C64XX
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
Frame buffer driver for the built-in FB controller in the Samsung
SoC line from the S3C2443 onwards, including the S3C2416, S3C2450,
and the S3C64XX series such as the S3C6400 and S3C6410.
These chips all have the same basic framebuffer design with the
actual capabilities depending on the chip. For instance the S3C6400
and S3C6410 support 4 hardware windows whereas the S3C24XX series
currently only have two.
Currently the support is only for the S3C6400 and S3C6410 SoCs.
config FB_S3C_DEBUG_REGWRITE
bool "Debug register writes"
depends on FB_S3C
---help---
Show all register writes via printk(KERN_DEBUG)
config FB_S3C2410
tristate "S3C2410 LCD framebuffer support"
depends on FB && ARCH_S3C2410
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
Frame buffer driver for the built-in LCD controller in the Samsung
S3C2410 processor.
This driver is also available as a module ( = code which can be
inserted and removed from the running kernel whenever you want). The
module will be called s3c2410fb. If you want to compile it as a module,
say M here and read <file:Documentation/kbuild/modules.txt>.
If unsure, say N.
config FB_S3C2410_DEBUG
bool "S3C2410 lcd debug messages"
depends on FB_S3C2410
help
Turn on debugging messages. Note that you can set/unset at run time
through sysfs
config FB_SM501
tristate "Silicon Motion SM501 framebuffer support"
depends on FB && MFD_SM501
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
Frame buffer driver for the CRT and LCD controllers in the Silicon
Motion SM501.
This driver is also available as a module ( = code which can be
inserted and removed from the running kernel whenever you want). The
module will be called sm501fb. If you want to compile it as a module,
say M here and read <file:Documentation/kbuild/modules.txt>.
If unsure, say N.
config FB_PNX4008_DUM
tristate "Display Update Module support on Philips PNX4008 board"
depends on FB && ARCH_PNX4008
---help---
Say Y here to enable support for PNX4008 Display Update Module (DUM)
config FB_PNX4008_DUM_RGB
tristate "RGB Framebuffer support on Philips PNX4008 board"
depends on FB_PNX4008_DUM
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
Say Y here to enable support for PNX4008 RGB Framebuffer
config FB_IBM_GXT4500
tristate "Framebuffer support for IBM GXT4500P adaptor"
depends on FB && PPC
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
Say Y here to enable support for the IBM GXT4500P display
adaptor, found on some IBM System P (pSeries) machines.
config FB_PS3
tristate "PS3 GPU framebuffer driver"
depends on FB && PS3_PS3AV
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
select FB_SYS_FOPS
select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE
---help---
Include support for the virtual frame buffer in the PS3 platform.
config FB_PS3_DEFAULT_SIZE_M
int "PS3 default frame buffer size (in MiB)"
depends on FB_PS3
default 9
---help---
This is the default size (in MiB) of the virtual frame buffer in
the PS3.
The default value can be overridden on the kernel command line
using the "ps3fb" option (e.g. "ps3fb=9M");
config FB_XILINX
tristate "Xilinx frame buffer support"
depends on FB && XILINX_VIRTEX
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
Include support for the Xilinx ML300/ML403 reference design
framebuffer. ML300 carries a 640*480 LCD display on the board,
ML403 uses a standard DB15 VGA connector.
config FB_COBALT
tristate "Cobalt server LCD frame buffer support"
depends on FB && MIPS_COBALT
config FB_SH7760
bool "SH7760/SH7763/SH7720/SH7721 LCDC support"
depends on FB && (CPU_SUBTYPE_SH7760 || CPU_SUBTYPE_SH7763 \
|| CPU_SUBTYPE_SH7720 || CPU_SUBTYPE_SH7721)
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
Support for the SH7760/SH7763/SH7720/SH7721 integrated
(D)STN/TFT LCD Controller.
Supports display resolutions up to 1024x1024 pixel, grayscale and
color operation, with depths ranging from 1 bpp to 8 bpp monochrome
and 8, 15 or 16 bpp color; 90 degrees clockwise display rotation for
panels <= 320 pixel horizontal resolution.
config FB_VIRTUAL
tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
depends on FB
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
select FB_SYS_FOPS
---help---
This is a `virtual' frame buffer device. It operates on a chunk of
unswappable kernel memory instead of on the memory of a graphics
board. This means you cannot see any output sent to this frame
buffer device, while it does consume precious memory. The main use
of this frame buffer device is testing and debugging the frame
buffer subsystem. Do NOT enable it for normal systems! To protect
the innocent, it has to be enabled explicitly at boot time using the
kernel option `video=vfb:'.
To compile this driver as a module, choose M here: the
module will be called vfb. In order to load it, you must use
the vfb_enable=1 option.
If unsure, say N.
config XEN_FBDEV_FRONTEND
tristate "Xen virtual frame buffer support"
depends on FB && XEN
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
select FB_SYS_FOPS
select FB_DEFERRED_IO
default y
help
This driver implements the front-end of the Xen virtual
frame buffer driver. It communicates with a back-end
in another domain.
config FB_METRONOME
tristate "E-Ink Metronome/8track controller support"
depends on FB
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
select FB_SYS_FOPS
select FB_DEFERRED_IO
help
This driver implements support for the E-Ink Metronome
controller. The pre-release name for this device was 8track
and could also have been called by some vendors as PVI-nnnn.
config FB_MB862XX
tristate "Fujitsu MB862xx GDC support"
depends on FB
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
---help---
Frame buffer driver for Fujitsu Carmine/Coral-P(A)/Lime controllers.
config FB_MB862XX_PCI_GDC
bool "Carmine/Coral-P(A) GDC"
depends on PCI && FB_MB862XX
---help---
This enables framebuffer support for Fujitsu Carmine/Coral-P(A)
PCI graphics controller devices.
config FB_MB862XX_LIME
bool "Lime GDC"
depends on FB_MB862XX
depends on OF && !FB_MB862XX_PCI_GDC
select FB_FOREIGN_ENDIAN
select FB_LITTLE_ENDIAN
---help---
Framebuffer support for Fujitsu Lime GDC on host CPU bus.
config FB_PRE_INIT_FB
bool "Don't reinitialize, use bootloader's GDC/Display configuration"
depends on FB_MB862XX_LIME
---help---
Select this option if display contents should be inherited as set by
the bootloader.
config FB_MX3
tristate "MX3 Framebuffer support"
depends on FB && MX3_IPU
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
default y
help
This is a framebuffer device for the i.MX31 LCD Controller. So
far only synchronous displays are supported. If you plan to use
an LCD display with your i.MX31 system, say Y here.
config FB_BROADSHEET
tristate "E-Ink Broadsheet/Epson S1D13521 controller support"
depends on FB
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
select FB_SYS_FOPS
select FB_DEFERRED_IO
help
This driver implements support for the E-Ink Broadsheet
controller. The release name for this device was Epson S1D13521
and could also have been called by other names when coupled with
a bridge adapter.
source "drivers/video/omap/Kconfig"
source "drivers/video/backlight/Kconfig"
source "drivers/video/display/Kconfig"
if VT
source "drivers/video/console/Kconfig"
endif
if FB || SGI_NEWPORT_CONSOLE
source "drivers/video/logo/Kconfig"
endif
endmenu
