#ifndef __PMAC_ZILOG_H__
#define __PMAC_ZILOG_H__
#define pmz_debug(fmt,arg...) dev_dbg(&uap->dev->ofdev.dev, fmt, ## arg)
/*
* At most 2 ESCCs with 2 ports each
*/
#define MAX_ZS_PORTS 4
/*
* We wrap our port structure around the generic uart_port.
*/
#define NUM_ZSREGS 17
struct uart_pmac_port {
struct uart_port port;
struct uart_pmac_port *mate;
/* macio_dev for the escc holding this port (maybe be null on
* early inited port)
*/
struct macio_dev *dev;
/* device node to this port, this points to one of 2 childs
* of "escc" node (ie. ch-a or ch-b)
*/
struct device_node *node;
/* Port type as obtained from device tree (IRDA, modem, ...) */
int port_type;
u8 curregs[NUM_ZSREGS];
unsigned int flags;
#define PMACZILOG_FLAG_IS_CONS 0x00000001
#define PMACZILOG_FLAG_IS_KGDB 0x00000002
#define PMACZILOG_FLAG_MODEM_STATUS 0x00000004
#define PMACZILOG_FLAG_IS_CHANNEL_A 0x00000008
#define PMACZILOG_FLAG_REGS_HELD 0x00000010
#define PMACZILOG_FLAG_TX_STOPPED 0x00000020
#define PMACZILOG_FLAG_TX_ACTIVE 0x00000040
#define PMACZILOG_FLAG_ENABLED 0x00000080
#define PMACZILOG_FLAG_IS_IRDA 0x00000100
#define PMACZILOG_FLAG_IS_INTMODEM 0x00000200
#define PMACZILOG_FLAG_HAS_DMA 0x00000400
#define PMACZILOG_FLAG_RSRC_REQUESTED 0x00000800
#define PMACZILOG_FLAG_IS_ASLEEP 0x00001000
#define PMACZILOG_FLAG_IS_OPEN 0x00002000
#define PMACZILOG_FLAG_IS_IRQ_ON 0x00004000
#define PMACZILOG_FLAG_IS_EXTCLK 0x00008000
#define PMACZILOG_FLAG_BREAK 0x00010000
unsigned char parity_mask;
unsigned char prev_status;
volatile u8 __iomem *control_reg;
volatile u8 __iomem *data_reg;
unsigned int tx_dma_irq;
unsigned int rx_dma_irq;
volatile struct dbdma_regs __iomem *tx_dma_regs;
volatile struct dbdma_regs __iomem *rx_dma_regs;
struct ktermios termios_cache;
};
#define to_pmz(p) ((struct uart_pmac_port *)(p))
static inline struct uart_pmac_port *pmz_get_port_A(struct uart_pmac_port *uap)
{
if (uap->flags & PMACZILOG_FLAG_IS_CHANNEL_A)
return uap;
return uap->mate;
}
/*
* Register acessors. Note that we don't need to enforce a recovery
* delay on PCI PowerMac hardware, it's dealt in HW by the MacIO chip,
* though if we try to use this driver on older machines, we might have
* to add it back
*/
static inline u8 read_zsreg(struct uart_pmac_port *port, u8 reg)
{
if (reg != 0)
writeb(reg, port->control_reg);
return readb(port->control_reg);
}
static inline void write_zsreg(struct uart_pmac_port *port, u8 reg, u8 value)
{
if (reg != 0)
writeb(reg, port->control_reg);
writeb(value, port->control_reg);
}
static inline u8 read_zsdata(struct uart_pmac_port *port)
{
return readb(port->data_reg);
}
static inline void write_zsdata(struct uart_pmac_port *port, u8 data)
{
writeb(data, port->data_reg);
}
static inline void zssync(struct uart_pmac_port *port)
{
(void)readb(port->control_reg);
}
/* Conversion routines to/from brg time constants from/to bits
* per second.
*/
#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
#define ZS_CLOCK 3686400 /* Z8530 RTxC input clock rate */
/* The Zilog register set */
#define FLAG 0x7e
/* Write Register 0 */
#define R0 0 /* Register selects */
#define R1 1
#define R2 2
#define R3 3
#define R4 4
#define R5 5
#define R6 6
#define R7 7
#define R8 8
#define R9 9
#define R10 10
#define R11 11
#define R12 12
#define R13 13
#define R14 14
#define R15 15
#define R7P 16
#define NULLCODE 0 /* Null Code */
#define POINT_HIGH 0x8 /* Select upper half of registers */
#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
#define SEND_ABORT 0x18 /* HDLC Abort */
#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
#define RES_Tx_P 0x28 /* Reset TxINT Pending */
#define ERR_RES 0x30 /* Error Reset */
#define RES_H_IUS 0x38 /* Reset highest IUS */
#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
#define RES_EOM_L 0xC0 /* Reset EOM latch */
/* Write Register 1 */
#define EXT_INT_ENAB 0x1 /* Ext Int Enable */
#define TxINT_ENAB 0x2 /* Tx Int Enable */
#define PAR_SPEC 0x4 /* Parity is special condition */
#define RxINT_DISAB 0 /* Rx Int Disable */
#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
#define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */
#define INT_ERR_Rx 0x18 /* Int on error only */
#define RxINT_MASK 0x18
#define WT_RDY_RT 0x20 /* W/Req reflects recv if 1, xmit if 0 */
#define WT_FN_RDYFN 0x40 /* W/Req pin is DMA request if 1, wait if 0 */
#define WT_RDY_ENAB 0x80 /* Enable W/Req pin */
/* Write Register #2 (Interrupt Vector) */
/* Write Register 3 */
#define RxENABLE 0x1 /* Rx Enable */
#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
#define ADD_SM 0x4 /* Address Search Mode (SDLC) */
#define RxCRC_ENAB 0x8 /* Rx CRC Enable */
#define ENT_HM 0x10 /* Enter Hunt Mode */
#define AUTO_ENAB 0x20 /* Auto Enables */
#define Rx5 0x0 /* Rx 5 Bits/Character */
#define Rx7 0x40 /* Rx 7 Bits/Character */
#define Rx6 0x80 /* Rx 6 Bits/Character */
#define Rx8 0xc0 /* Rx 8 Bits/Character */
#define RxN_MASK 0xc0
/* Write Register 4 */
#define PAR_ENAB 0x1 /* Parity Enable */
#define PAR_EVEN 0x2 /* Parity Even/Odd* */
#define SYNC_ENAB 0 /* Sync Modes Enable */
#define SB1 0x4 /* 1 stop bit/char */
#define SB15 0x8 /* 1.5 stop bits/char */
#define SB2 0xc /* 2 stop bits/char */
#define SB_MASK 0xc
#define MONSYNC 0 /* 8 Bit Sync character */
#define BISYNC 0x10 /* 16 bit sync character */
#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
#define EXTSYNC 0x30 /* External Sync Mode */
#define X1CLK 0x0 /* x1 clock mode */
#define X16CLK 0x40 /* x16 clock mode */
#define X32CLK 0x80 /* x32 clock mode */
#define X64CLK 0xC0 /* x64 clock mode */
#define XCLK_MASK 0xC0
/* Write Register 5 */
#define TxCRC_ENAB 0x1 /* Tx CRC Enable */
#define RTS 0x2 /* RTS */
#define SDLC_CRC 0x4 /* SDLC/CRC-16 */
#define TxENABLE 0x8 /* Tx Enable */
#define SND_BRK 0x10 /* Send Break */
#define Tx5 0x0 /* Tx 5 bits (or less)/character */
#define Tx7 0x20 /* Tx 7 bits/character */
#define Tx6 0x40 /* Tx 6 bits/character */
#define Tx8 0x60 /* Tx 8 bits/character */
#define TxN_MASK 0x60
#define DTR 0x80 /* DTR */
/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
/* Write Register 7' (Some enhanced feature control) */
#define ENEXREAD 0x40 /* Enable read of some write registers */
/* Write Register 8 (transmit buffer) */
/* Write Register 9 (Master interrupt control) */
#define VIS 1 /* Vector Includes Status */
#define NV 2 /* No Vector */
#define DLC 4 /* Disable Lower Chain */
#define MIE 8 /* Master Interrupt Enable */
#define STATHI 0x10 /* Status high */
#define NORESET 0 /* No reset on write to R9 */
#define CHRB 0x40 /* Reset channel B */
#define CHRA 0x80 /* Reset channel A */
#define FHWRES 0xc0 /* Force hardware reset */
/* Write Register 10 (misc control bits) */
#define BIT6 1 /* 6 bit/8bit sync */
#define LOOPMODE 2 /* SDLC Loop mode */
#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
#define MARKIDLE 8 /* Mark/flag on idle */
#define GAOP 0x10 /* Go active on poll */
#define NRZ 0 /* NRZ mode */
#define NRZI 0x20 /* NRZI mode */
#define FM1 0x40 /* FM1 (transition = 1) */
#define FM0 0x60 /* FM0 (transition = 0) */
#define CRCPS 0x80 /* CRC Preset I/O */
/* Write Register 11 (Clock Mode control) */
#define TRxCXT 0 /* TRxC = Xtal output */
#define TRxCTC 1 /* TRxC = Transmit clock */
#define TRxCBR 2 /* TRxC = BR Generator Output */
#define TRxCDP 3 /* TRxC = DPLL output */
#define TRxCOI 4 /* TRxC O/I */
#define TCRTxCP 0 /* Transmit clock = RTxC pin */
#define TCTRxCP 8 /* Transmit clock = TRxC pin */
#define TCBR 0x10 /* Transmit clock = BR Generator output */
#define TCDPLL 0x18 /* Transmit clock = DPLL output */
#define RCRTxCP 0 /* Receive clock = RTxC pin */
#define RCTRxCP 0x20 /* Receive clock = TRxC pin */
#define RCBR 0x40 /* Receive clock = BR Generator output */
#define RCDPLL 0x60 /* Receive clock = DPLL output */
#define RTxCX 0x80 /* RTxC Xtal/No Xtal */
/* Write Register 12 (lower byte of baud rate generator time constant) */
/* Write Register 13 (upper byte of baud rate generator time constant) */
/* Write Register 14 (Misc control bits) */
#define BRENAB 1 /* Baud rate generator enable */
#define BRSRC 2 /* Baud rate generator source */
#define DTRREQ 4 /* DTR/Request function */
#define AUTOECHO 8 /* Auto Echo */
#define LOOPBAK 0x10 /* Local loopback */
#define SEARCH 0x20 /* Enter search mode */
#define RMC 0x40 /* Reset missing clock */
#define DISDPLL 0x60 /* Disable DPLL */
#define SSBR 0x80 /* Set DPLL source = BR generator */
#define SSRTxC 0xa0 /* Set DPLL source = RTxC */
#define SFMM 0xc0 /* Set FM mode */
#define SNRZI 0xe0 /* Set NRZI mode */
/* Write Register 15 (external/status interrupt control) */
#define EN85C30 1 /* Enable some 85c30-enhanced registers */
#define ZCIE 2 /* Zero count IE */
#define ENSTFIFO 4 /* Enable status FIFO (SDLC) */
#define DCDIE 8 /* DCD IE */
#define SYNCIE 0x10 /* Sync/hunt IE */
#define CTSIE 0x20 /* CTS IE */
#define TxUIE 0x40 /* Tx Underrun/EOM IE */
#define BRKIE 0x80 /* Break/Abort IE */
/* Read Register 0 */
#define Rx_CH_AV 0x1 /* Rx Character Available */
#define ZCOUNT 0x2 /* Zero count */
#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
#define DCD 0x8 /* DCD */
#define SYNC_HUNT 0x10 /* Sync/hunt */
#define CTS 0x20 /* CTS */
#define TxEOM 0x40 /* Tx underrun */
#define BRK_ABRT 0x80 /* Break/Abort */
/* Read Register 1 */
#define ALL_SNT 0x1 /* All sent */
/* Residue Data for 8 Rx bits/char programmed */
#define RES3 0x8 /* 0/3 */
#define RES4 0x4 /* 0/4 */
#define RES5 0xc /* 0/5 */
#define RES6 0x2 /* 0/6 */
#define RES7 0xa /* 0/7 */
#define RES8 0x6 /* 0/8 */
#define RES18 0xe /* 1/8 */
#define RES28 0x0 /* 2/8 */
/* Special Rx Condition Interrupts */
#define PAR_ERR 0x10 /* Parity error */
#define Rx_OVR 0x20 /* Rx Overrun Error */
#define CRC_ERR 0x40 /* CRC/Framing Error */
#define END_FR 0x80 /* End of Frame (SDLC) */
/* Read Register 2 (channel b only) - Interrupt vector */
#define CHB_Tx_EMPTY 0x00
#define CHB_EXT_STAT 0x02
#define CHB_Rx_AVAIL 0x04
#define CHB_SPECIAL 0x06
#define CHA_Tx_EMPTY 0x08
#define CHA_EXT_STAT 0x0a
#define CHA_Rx_AVAIL 0x0c
#define CHA_SPECIAL 0x0e
#define STATUS_MASK 0x06
/* Read Register 3 (interrupt pending register) ch a only */
#define CHBEXT 0x1 /* Channel B Ext/Stat IP */
#define CHBTxIP 0x2 /* Channel B Tx IP */
#define CHBRxIP 0x4 /* Channel B Rx IP */
#define CHAEXT 0x8 /* Channel A Ext/Stat IP */
#define CHATxIP 0x10 /* Channel A Tx IP */
#define CHARxIP 0x20 /* Channel A Rx IP */
/* Read Register 8 (receive data register) */
/* Read Register 10 (misc status bits) */
#define ONLOOP 2 /* On loop */
#define LOOPSEND 0x10 /* Loop sending */
#define CLK2MIS 0x40 /* Two clocks missing */
#define CLK1MIS 0x80 /* One clock missing */
/* Read Register 12 (lower byte of baud rate generator constant) */
/* Read Register 13 (upper byte of baud rate generator constant) */
/* Read Register 15 (value of WR 15) */
/* Misc macros */
#define ZS_CLEARERR(port) (write_zsreg(port, 0, ERR_RES))
#define ZS_CLEARFIFO(port) do { volatile unsigned char garbage; \
garbage = read_zsdata(port); \
garbage = read_zsdata(port); \
garbage = read_zsdata(port); \
} while(0)
#define ZS_IS_CONS(UP) ((UP)->flags & PMACZILOG_FLAG_IS_CONS)
#define ZS_IS_KGDB(UP) ((UP)->flags & PMACZILOG_FLAG_IS_KGDB)
#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & PMACZILOG_FLAG_IS_CHANNEL_A)
#define ZS_REGS_HELD(UP) ((UP)->flags & PMACZILOG_FLAG_REGS_HELD)
#define ZS_TX_STOPPED(UP) ((UP)->flags & PMACZILOG_FLAG_TX_STOPPED)
#define ZS_TX_ACTIVE(UP) ((UP)->flags & PMACZILOG_FLAG_TX_ACTIVE)
#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & PMACZILOG_FLAG_MODEM_STATUS)
#define ZS_IS_IRDA(UP) ((UP)->flags & PMACZILOG_FLAG_IS_IRDA)
#define ZS_IS_INTMODEM(UP) ((UP)->flags & PMACZILOG_FLAG_IS_INTMODEM)
#define ZS_HAS_DMA(UP) ((UP)->flags & PMACZILOG_FLAG_HAS_DMA)
#define ZS_IS_ASLEEP(UP) ((UP)->flags & PMACZILOG_FLAG_IS_ASLEEP)
#define ZS_IS_OPEN(UP) ((UP)->flags & PMACZILOG_FLAG_IS_OPEN)
#define ZS_IS_IRQ_ON(UP) ((UP)->flags & PMACZILOG_FLAG_IS_IRQ_ON)
#define ZS_IS_EXTCLK(UP) ((UP)->flags & PMACZILOG_FLAG_IS_EXTCLK)
#endif /* __PMAC_ZILOG_H__ */
