#
# Serial device configuration
#
# $Id: Kconfig,v 1.11 2004/03/11 18:08:04 lethal Exp $
#
menu "Serial drivers"
depends on HAS_IOMEM
#
# The new 8250/16550 serial drivers
config SERIAL_8250
tristate "8250/16550 and compatible serial support"
depends on (BROKEN || !SPARC)
select SERIAL_CORE
---help---
This selects whether you want to include the driver for the standard
serial ports. The standard answer is Y. People who might say N
here are those that are setting up dedicated Ethernet WWW/FTP
servers, or users that have one of the various bus mice instead of a
serial mouse and don't intend to use their machine's standard serial
port for anything. (Note that the Cyclades and Stallion multi
serial port drivers do not need this driver built in for them to
work.)
To compile this driver as a module, choose M here: the
module will be called 8250.
[WARNING: Do not compile this driver as a module if you are using
non-standard serial ports, since the configuration information will
be lost when the driver is unloaded. This limitation may be lifted
in the future.]
BTW1: If you have a mouseman serial mouse which is not recognized by
the X window system, try running gpm first.
BTW2: If you intend to use a software modem (also called Winmodem)
under Linux, forget it. These modems are crippled and require
proprietary drivers which are only available under Windows.
Most people will say Y or M here, so that they can use serial mice,
modems and similar devices connecting to the standard serial ports.
config SERIAL_8250_CONSOLE
bool "Console on 8250/16550 and compatible serial port"
depends on SERIAL_8250=y
select SERIAL_CORE_CONSOLE
---help---
If you say Y here, it will be possible to use a serial port as the
system console (the system console is the device which receives all
kernel messages and warnings and which allows logins in single user
mode). This could be useful if some terminal or printer is connected
to that serial port.
Even if you say Y here, the currently visible virtual console
(/dev/tty0) will still be used as the system console by default, but
you can alter that using a kernel command line option such as
"console=ttyS1". (Try "man bootparam" or see the documentation of
your boot loader (grub or lilo or loadlin) about how to pass options
to the kernel at boot time.)
If you don't have a VGA card installed and you say Y here, the
kernel will automatically use the first serial line, /dev/ttyS0, as
system console.
You can set that using a kernel command line option such as
"console=uart8250,io,0x3f8,9600n8"
"console=uart8250,mmio,0xff5e0000,115200n8".
and it will switch to normal serial console when the corresponding
port is ready.
"earlycon=uart8250,io,0x3f8,9600n8"
"earlycon=uart8250,mmio,0xff5e0000,115200n8".
it will not only setup early console.
If unsure, say N.
config FIX_EARLYCON_MEM
bool
depends on X86
default y
config SERIAL_8250_GSC
tristate
depends on SERIAL_8250 && GSC
default SERIAL_8250
config SERIAL_8250_PCI
tristate "8250/16550 PCI device support" if EMBEDDED
depends on SERIAL_8250 && PCI
default SERIAL_8250
help
This builds standard PCI serial support. You may be able to
disable this feature if you only need legacy serial support.
Saves about 9K.
config SERIAL_8250_PNP
tristate "8250/16550 PNP device support" if EMBEDDED
depends on SERIAL_8250 && PNP
default SERIAL_8250
help
This builds standard PNP serial support. You may be able to
disable this feature if you only need legacy serial support.
config SERIAL_8250_HP300
tristate
depends on SERIAL_8250 && HP300
default SERIAL_8250
config SERIAL_8250_CS
tristate "8250/16550 PCMCIA device support"
depends on PCMCIA && SERIAL_8250
---help---
Say Y here to enable support for 16-bit PCMCIA serial devices,
including serial port cards, modems, and the modem functions of
multi-function Ethernet/modem cards. (PCMCIA- or PC-cards are
credit-card size devices often used with laptops.)
To compile this driver as a module, choose M here: the
module will be called serial_cs.
If unsure, say N.
config SERIAL_8250_NR_UARTS
int "Maximum number of 8250/16550 serial ports"
depends on SERIAL_8250
default "4"
help
Set this to the number of serial ports you want the driver
to support. This includes any ports discovered via ACPI or
PCI enumeration and any ports that may be added at run-time
via hot-plug, or any ISA multi-port serial cards.
config SERIAL_8250_RUNTIME_UARTS
int "Number of 8250/16550 serial ports to register at runtime"
depends on SERIAL_8250
range 0 SERIAL_8250_NR_UARTS
default "4"
help
Set this to the maximum number of serial ports you want
the kernel to register at boot time. This can be overridden
with the module parameter "nr_uarts", or boot-time parameter
8250.nr_uarts
config SERIAL_8250_EXTENDED
bool "Extended 8250/16550 serial driver options"
depends on SERIAL_8250
help
If you wish to use any non-standard features of the standard "dumb"
driver, say Y here. This includes HUB6 support, shared serial
interrupts, special multiport support, support for more than the
four COM 1/2/3/4 boards, etc.
Note that the answer to this question won't directly affect the
kernel: saying N will just cause the configurator to skip all
the questions about serial driver options. If unsure, say N.
config SERIAL_8250_MANY_PORTS
bool "Support more than 4 legacy serial ports"
depends on SERIAL_8250_EXTENDED && !IA64
help
Say Y here if you have dumb serial boards other than the four
standard COM 1/2/3/4 ports. This may happen if you have an AST
FourPort, Accent Async, Boca (read the Boca mini-HOWTO, available
from <http://www.tldp.org/docs.html#howto>), or other custom
serial port hardware which acts similar to standard serial port
hardware. If you only use the standard COM 1/2/3/4 ports, you can
say N here to save some memory. You can also say Y if you have an
"intelligent" multiport card such as Cyclades, Digiboards, etc.
#
# Multi-port serial cards
#
config SERIAL_8250_FOURPORT
tristate "Support Fourport cards"
depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS
help
Say Y here if you have an AST FourPort serial board.
To compile this driver as a module, choose M here: the module
will be called 8250_fourport.
config SERIAL_8250_ACCENT
tristate "Support Accent cards"
depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS
help
Say Y here if you have an Accent Async serial board.
To compile this driver as a module, choose M here: the module
will be called 8250_accent.
config SERIAL_8250_BOCA
tristate "Support Boca cards"
depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS
help
Say Y here if you have a Boca serial board. Please read the Boca
mini-HOWTO, available from <http://www.tldp.org/docs.html#howto>
To compile this driver as a module, choose M here: the module
will be called 8250_boca.
config SERIAL_8250_EXAR_ST16C554
tristate "Support Exar ST16C554/554D Quad UART"
depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS
help
The Uplogix Envoy TU301 uses this Exar Quad UART. If you are
tinkering with your Envoy TU301, or have a machine with this UART,
say Y here.
To compile this driver as a module, choose M here: the module
will be called 8250_exar_st16c554.
config SERIAL_8250_HUB6
tristate "Support Hub6 cards"
depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS
help
Say Y here if you have a HUB6 serial board.
To compile this driver as a module, choose M here: the module
will be called 8250_hub6.
config SERIAL_8250_SHARE_IRQ
bool "Support for sharing serial interrupts"
depends on SERIAL_8250_EXTENDED
help
Some serial boards have hardware support which allows multiple dumb
serial ports on the same board to share a single IRQ. To enable
support for this in the serial driver, say Y here.
config SERIAL_8250_DETECT_IRQ
bool "Autodetect IRQ on standard ports (unsafe)"
depends on SERIAL_8250_EXTENDED
help
Say Y here if you want the kernel to try to guess which IRQ
to use for your serial port.
This is considered unsafe; it is far better to configure the IRQ in
a boot script using the setserial command.
If unsure, say N.
config SERIAL_8250_RSA
bool "Support RSA serial ports"
depends on SERIAL_8250_EXTENDED
help
::: To be written :::
config SERIAL_8250_MCA
tristate "Support 8250-type ports on MCA buses"
depends on SERIAL_8250 != n && MCA
help
Say Y here if you have a MCA serial ports.
To compile this driver as a module, choose M here: the module
will be called 8250_mca.
config SERIAL_8250_ACORN
tristate "Acorn expansion card serial port support"
depends on ARCH_ACORN && SERIAL_8250
help
If you have an Atomwide Serial card or Serial Port card for an Acorn
system, say Y to this option. The driver can handle 1, 2, or 3 port
cards. If unsure, say N.
config SERIAL_8250_AU1X00
bool "Au1x00 serial port support"
depends on SERIAL_8250 != n && SOC_AU1X00
help
If you have an Au1x00 SOC based board and want to use the serial port,
say Y to this option. The driver can handle up to 4 serial ports,
depending on the SOC. If unsure, say N.
config SERIAL_8250_RM9K
bool "Support for MIPS RM9xxx integrated serial port"
depends on SERIAL_8250 != n && SERIAL_RM9000
select SERIAL_8250_SHARE_IRQ
help
Selecting this option will add support for the integrated serial
port hardware found on MIPS RM9122 and similar processors.
If unsure, say N.
comment "Non-8250 serial port support"
config SERIAL_AMBA_PL010
tristate "ARM AMBA PL010 serial port support"
depends on ARM_AMBA && (BROKEN || !ARCH_VERSATILE)
select SERIAL_CORE
help
This selects the ARM(R) AMBA(R) PrimeCell PL010 UART. If you have
an Integrator/AP or Integrator/PP2 platform, or if you have a
Cirrus Logic EP93xx CPU, say Y or M here.
If unsure, say N.
config SERIAL_AMBA_PL010_CONSOLE
bool "Support for console on AMBA serial port"
depends on SERIAL_AMBA_PL010=y
select SERIAL_CORE_CONSOLE
---help---
Say Y here if you wish to use an AMBA PrimeCell UART as the system
console (the system console is the device which receives all kernel
messages and warnings and which allows logins in single user mode).
Even if you say Y here, the currently visible framebuffer console
(/dev/tty0) will still be used as the system console by default, but
you can alter that using a kernel command line option such as
"console=ttyAM0". (Try "man bootparam" or see the documentation of
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
config SERIAL_AMBA_PL011
tristate "ARM AMBA PL011 serial port support"
depends on ARM_AMBA
select SERIAL_CORE
help
This selects the ARM(R) AMBA(R) PrimeCell PL011 UART. If you have
an Integrator/PP2, Integrator/CP or Versatile platform, say Y or M
here.
If unsure, say N.
config SERIAL_AMBA_PL011_CONSOLE
bool "Support for console on AMBA serial port"
depends on SERIAL_AMBA_PL011=y
select SERIAL_CORE_CONSOLE
---help---
Say Y here if you wish to use an AMBA PrimeCell UART as the system
console (the system console is the device which receives all kernel
messages and warnings and which allows logins in single user mode).
Even if you say Y here, the currently visible framebuffer console
(/dev/tty0) will still be used as the system console by default, but
you can alter that using a kernel command line option such as
"console=ttyAMA0". (Try "man bootparam" or see the documentation of
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
config SERIAL_SB1250_DUART
tristate "BCM1xxx on-chip DUART serial support"
depends on SIBYTE_SB1xxx_SOC=y
select SERIAL_CORE
default y
---help---
Support for the asynchronous serial interface (DUART) included in
the BCM1250 and derived System-On-a-Chip (SOC) devices. Note that
the letter D in DUART stands for "dual", which is how the device
is implemented. Depending on the SOC configuration there may be
one or more DUARTs available of which all are handled.
If unsure, say Y. To compile this driver as a module, choose M here:
the module will be called sb1250-duart.
config SERIAL_SB1250_DUART_CONSOLE
bool "Support for console on a BCM1xxx DUART serial port"
depends on SERIAL_SB1250_DUART=y
select SERIAL_CORE_CONSOLE
default y
---help---
If you say Y here, it will be possible to use a serial port as the
system console (the system console is the device which receives all
kernel messages and warnings and which allows logins in single user
mode).
If unsure, say Y.
config SERIAL_ATMEL
bool "AT91 / AT32 on-chip serial port support"
depends on (ARM && ARCH_AT91) || AVR32
select SERIAL_CORE
help
This enables the driver for the on-chip UARTs of the Atmel
AT91 and AT32 processors.
config SERIAL_ATMEL_CONSOLE
bool "Support for console on AT91 / AT32 serial port"
depends on SERIAL_ATMEL=y
select SERIAL_CORE_CONSOLE
help
Say Y here if you wish to use an on-chip UART on a Atmel
AT91 or AT32 processor as the system console (the system
console is the device which receives all kernel messages and
warnings and which allows logins in single user mode).
config SERIAL_ATMEL_PDC
bool "Support DMA transfers on AT91 / AT32 serial port"
depends on SERIAL_ATMEL
default y
help
Say Y here if you wish to use the PDC to do DMA transfers to
and from the Atmel AT91 / AT32 serial port. In order to
actually use DMA transfers, make sure that the use_dma_tx
and use_dma_rx members in the atmel_uart_data struct is set
appropriately for each port.
Note that break and error handling currently doesn't work
properly when DMA is enabled. Make sure that ports where
this matters don't use DMA.
config SERIAL_ATMEL_TTYAT
bool "Install as device ttyATn instead of ttySn"
depends on SERIAL_ATMEL=y
help
Say Y here if you wish to have the internal AT91 / AT32 UARTs
appear as /dev/ttyATn (major 204, minor starting at 154)
instead of the normal /dev/ttySn (major 4, minor starting at
64). This is necessary if you also want other UARTs, such as
external 8250/16C550 compatible UARTs.
The ttySn nodes are legally reserved for the 8250 serial driver
but are often misused by other serial drivers.
To use this, you should create suitable ttyATn device nodes in
/dev/, and pass "console=ttyATn" to the kernel.
Say Y if you have an external 8250/16C550 UART. If unsure, say N.
config SERIAL_KS8695
bool "Micrel KS8695 (Centaur) serial port support"
depends on ARCH_KS8695
select SERIAL_CORE
help
This selects the Micrel Centaur KS8695 UART. Say Y here.
config SERIAL_KS8695_CONSOLE
bool "Support for console on KS8695 (Centaur) serial port"
depends on SERIAL_KS8695=y
select SERIAL_CORE_CONSOLE
help
Say Y here if you wish to use a KS8695 (Centaur) UART as the
system console (the system console is the device which
receives all kernel messages and warnings and which allows
logins in single user mode).
config SERIAL_CLPS711X
tristate "CLPS711X serial port support"
depends on ARM && ARCH_CLPS711X
select SERIAL_CORE
help
::: To be written :::
config SERIAL_CLPS711X_CONSOLE
bool "Support for console on CLPS711X serial port"
depends on SERIAL_CLPS711X=y
select SERIAL_CORE_CONSOLE
help
Even if you say Y here, the currently visible virtual console
(/dev/tty0) will still be used as the system console by default, but
you can alter that using a kernel command line option such as
"console=ttyCL1". (Try "man bootparam" or see the documentation of
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
config SERIAL_SAMSUNG
tristate "Samsung SoC serial support"
depends on ARM && PLAT_S3C24XX
help
Support for the on-chip UARTs on the Samsung S3C24XX series CPUs,
providing /dev/ttySAC0, 1 and 2 (note, some machines may not
provide all of these ports, depending on how the serial port
pins are configured.
config SERIAL_SAMSUNG_DEBUG
bool "Samsung SoC serial debug"
depends on SERIAL_SAMSUNG
help
Add support for debugging the serial driver. Since this is
generally being used as a console, we use our own output
routines that go via the low-level debug printascii()
function.
config SERIAL_SAMSUNG_CONSOLE
bool "Support for console on Samsung SoC serial port"
depends on SERIAL_SAMSUNG=y
select SERIAL_CORE_CONSOLE
help
Allow selection of the S3C24XX on-board serial ports for use as
an virtual console.
Even if you say Y here, the currently visible virtual console
(/dev/tty0) will still be used as the system console by default, but
you can alter that using a kernel command line option such as
"console=ttySACx". (Try "man bootparam" or see the documentation of
your boot loader about how to pass options to the kernel at
boot time.)
config SERIAL_S3C2400
tristate "Samsung S3C2410 Serial port support"
depends on ARM && SERIAL_SAMSUNG && CPU_S3C2400
default y if CPU_S3C2400
help
Serial port support for the Samsung S3C2400 SoC
config SERIAL_S3C2410
tristate "Samsung S3C2410 Serial port support"
depends on SERIAL_SAMSUNG && CPU_S3C2410
default y if CPU_S3C2410
help
Serial port support for the Samsung S3C2410 SoC
config SERIAL_S3C2412
tristate "Samsung S3C2412/S3C2413 Serial port support"
depends on SERIAL_SAMSUNG && CPU_S3C2412
default y if CPU_S3C2412
help
Serial port support for the Samsung S3C2412 and S3C2413 SoC
config SERIAL_S3C2440
tristate "Samsung S3C2440/S3C2442 Serial port support"
depends on SERIAL_SAMSUNG && (CPU_S3C2440 || CPU_S3C2442)
default y if CPU_S3C2440
default y if CPU_S3C2442
help
Serial port support for the Samsung S3C2440 and S3C2442 SoC
config SERIAL_DZ
bool "DECstation DZ serial driver"
depends on MACH_DECSTATION && 32BIT
select SERIAL_CORE
default y
---help---
DZ11-family serial controllers for DECstations and VAXstations,
including the DC7085, M7814, and M7819.
config SERIAL_DZ_CONSOLE
bool "Support console on DECstation DZ serial driver"
depends on SERIAL_DZ=y
select SERIAL_CORE_CONSOLE
default y
---help---
If you say Y here, it will be possible to use a serial port as the
system console (the system console is the device which receives all
kernel messages and warnings and which allows logins in single user
mode).
Note that the firmware uses ttyS3 as the serial console on
DECstations that use this driver.
If unsure, say Y.
config SERIAL_ZS
tristate "DECstation Z85C30 serial support"
depends on MACH_DECSTATION
select SERIAL_CORE
default y
---help---
Support for the Zilog 85C350 serial communications controller used
for serial ports in newer DECstation systems. These include the
DECsystem 5900 and all models of the DECstation and DECsystem 5000
systems except from model 200.
If unsure, say Y. To compile this driver as a module, choose M here:
the module will be called zs.
config SERIAL_ZS_CONSOLE
bool "Support for console on a DECstation Z85C30 serial port"
depends on SERIAL_ZS=y
select SERIAL_CORE_CONSOLE
default y
---help---
If you say Y here, it will be possible to use a serial port as the
system console (the system console is the device which receives all
kernel messages and warnings and which allows logins in single user
mode).
Note that the firmware uses ttyS1 as the serial console on the
Maxine and ttyS3 on the others using this driver.
If unsure, say Y.
config SERIAL_21285
tristate "DC21285 serial port support"
depends on ARM && FOOTBRIDGE
select SERIAL_CORE
help
If you have a machine based on a 21285 (Footbridge) StrongARM(R)/
PCI bridge you can enable its onboard serial port by enabling this
option.
config SERIAL_21285_CONSOLE
bool "Console on DC21285 serial port"
depends on SERIAL_21285=y
select SERIAL_CORE_CONSOLE
help
If you have enabled the serial port on the 21285 footbridge you can
make it the console by answering Y to this option.
Even if you say Y here, the currently visible virtual console
(/dev/tty0) will still be used as the system console by default, but
you can alter that using a kernel command line option such as
"console=ttyFB". (Try "man bootparam" or see the documentation of
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
config SERIAL_MPSC
bool "Marvell MPSC serial port support"
depends on PPC32 && MV64X60
select SERIAL_CORE
help
Say Y here if you want to use the Marvell MPSC serial controller.
config SERIAL_MPSC_CONSOLE
bool "Support for console on Marvell MPSC serial port"
depends on SERIAL_MPSC
select SERIAL_CORE_CONSOLE
help
Say Y here if you want to support a serial console on a Marvell MPSC.
config SERIAL_PXA
bool "PXA serial port support"
depends on ARM && ARCH_PXA
select SERIAL_CORE
help
If you have a machine based on an Intel XScale PXA2xx CPU you
can enable its onboard serial ports by enabling this option.
config SERIAL_PXA_CONSOLE
bool "Console on PXA serial port"
depends on SERIAL_PXA
select SERIAL_CORE_CONSOLE
help
If you have enabled the serial port on the Intel XScale PXA
CPU you can make it the console by answering Y to this option.
Even if you say Y here, the currently visible virtual console
(/dev/tty0) will still be used as the system console by default, but
you can alter that using a kernel command line option such as
"console=ttySA0". (Try "man bootparam" or see the documentation of
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
config SERIAL_SA1100
bool "SA1100 serial port support"
depends on ARM && ARCH_SA1100
select SERIAL_CORE
help
If you have a machine based on a SA1100/SA1110 StrongARM(R) CPU you
can enable its onboard serial port by enabling this option.
Please read <file:Documentation/arm/SA1100/serial_UART> for further
info.
config SERIAL_SA1100_CONSOLE
bool "Console on SA1100 serial port"
depends on SERIAL_SA1100
select SERIAL_CORE_CONSOLE
help
If you have enabled the serial port on the SA1100/SA1110 StrongARM
CPU you can make it the console by answering Y to this option.
Even if you say Y here, the currently visible virtual console
(/dev/tty0) will still be used as the system console by default, but
you can alter that using a kernel command line option such as
"console=ttySA0". (Try "man bootparam" or see the documentation of
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
config SERIAL_BFIN
tristate "Blackfin serial port support"
depends on BLACKFIN
select SERIAL_CORE
select SERIAL_BFIN_UART0 if (BF531 || BF532 || BF533 || BF561)
help
Add support for the built-in UARTs on the Blackfin.
To compile this driver as a module, choose M here: the
module will be called bfin_5xx.
config SERIAL_BFIN_CONSOLE
bool "Console on Blackfin serial port"
depends on SERIAL_BFIN=y
select SERIAL_CORE_CONSOLE
choice
prompt "UART Mode"
depends on SERIAL_BFIN
default SERIAL_BFIN_DMA
help
This driver supports the built-in serial ports of the Blackfin family
of CPUs
config SERIAL_BFIN_DMA
bool "DMA mode"
depends on !DMA_UNCACHED_NONE && !KGDB_UART
help
This driver works under DMA mode. If this option is selected, the
blackfin simple dma driver is also enabled.
config SERIAL_BFIN_PIO
bool "PIO mode"
help
This driver works under PIO mode.
endchoice
config SERIAL_BFIN_UART0
bool "Enable UART0"
depends on SERIAL_BFIN
help
Enable UART0
config BFIN_UART0_CTSRTS
bool "Enable UART0 hardware flow control"
depends on SERIAL_BFIN_UART0
help
Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
signal.
config UART0_CTS_PIN
int "UART0 CTS pin"
depends on BFIN_UART0_CTSRTS
default 23
help
The default pin is GPIO_GP7.
Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
config UART0_RTS_PIN
int "UART0 RTS pin"
depends on BFIN_UART0_CTSRTS
default 22
help
The default pin is GPIO_GP6.
Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
config SERIAL_BFIN_UART1
bool "Enable UART1"
depends on SERIAL_BFIN && (!BF531 && !BF532 && !BF533 && !BF561)
help
Enable UART1
config BFIN_UART1_CTSRTS
bool "Enable UART1 hardware flow control"
depends on SERIAL_BFIN_UART1
help
Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
signal.
config UART1_CTS_PIN
int "UART1 CTS pin"
depends on BFIN_UART1_CTSRTS && !BF54x
default -1
help
Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
config UART1_RTS_PIN
int "UART1 RTS pin"
depends on BFIN_UART1_CTSRTS && !BF54x
default -1
help
Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
config SERIAL_BFIN_UART2
bool "Enable UART2"
depends on SERIAL_BFIN && (BF54x)
help
Enable UART2
config BFIN_UART2_CTSRTS
bool "Enable UART2 hardware flow control"
depends on SERIAL_BFIN_UART2
help
Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
signal.
config UART2_CTS_PIN
int "UART2 CTS pin"
depends on BFIN_UART2_CTSRTS
default -1
help
Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
config UART2_RTS_PIN
int "UART2 RTS pin"
depends on BFIN_UART2_CTSRTS
default -1
help
Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
config SERIAL_BFIN_UART3
bool "Enable UART3"
depends on SERIAL_BFIN && (BF54x)
help
Enable UART3
config BFIN_UART3_CTSRTS
bool "Enable UART3 hardware flow control"
depends on SERIAL_BFIN_UART3
help
Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
signal.
config SERIAL_IMX
bool "IMX serial port support"
depends on ARM && (ARCH_IMX || ARCH_MXC)
select SERIAL_CORE
help
If you have a machine based on a Motorola IMX CPU you
can enable its onboard serial port by enabling this option.
config SERIAL_IMX_CONSOLE
bool "Console on IMX serial port"
depends on SERIAL_IMX
select SERIAL_CORE_CONSOLE
help
If you have enabled the serial port on the Motorola IMX
CPU you can make it the console by answering Y to this option.
Even if you say Y here, the currently visible virtual console
(/dev/tty0) will still be used as the system console by default, but
you can alter that using a kernel command line option such as
"console=ttySA0". (Try "man bootparam" or see the documentation of
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
config SERIAL_UARTLITE
tristate "Xilinx uartlite serial port support"
depends on PPC32
select SERIAL_CORE
help
Say Y here if you want to use the Xilinx uartlite serial controller.
To compile this driver as a module, choose M here: the
module will be called uartlite.ko.
config SERIAL_UARTLITE_CONSOLE
bool "Support for console on Xilinx uartlite serial port"
depends on SERIAL_UARTLITE=y
select SERIAL_CORE_CONSOLE
help
Say Y here if you wish to use a Xilinx uartlite as the system
console (the system console is the device which receives all kernel
messages and warnings and which allows logins in single user mode).
config SERIAL_SUNCORE
bool
depends on SPARC
select SERIAL_CORE
select SERIAL_CORE_CONSOLE
default y
config SERIAL_SUNZILOG
tristate "Sun Zilog8530 serial support"
depends on SPARC
help
This driver supports the Zilog8530 serial ports found on many Sparc
systems. Say Y or M if you want to be able to these serial ports.
config SERIAL_SUNZILOG_CONSOLE
bool "Console on Sun Zilog8530 serial port"
depends on SERIAL_SUNZILOG=y
help
If you would like to be able to use the Zilog8530 serial port
on your Sparc system as the console, you can do so by answering
Y to this option.
config SERIAL_SUNSU
tristate "Sun SU serial support"
depends on SPARC && PCI
help
This driver supports the 8250 serial ports that run the keyboard and
mouse on (PCI) UltraSPARC systems. Say Y or M if you want to be able
to these serial ports.
config SERIAL_SUNSU_CONSOLE
bool "Console on Sun SU serial port"
depends on SERIAL_SUNSU=y
help
If you would like to be able to use the SU serial port
on your Sparc system as the console, you can do so by answering
Y to this option.
config SERIAL_MUX
tristate "Serial MUX support"
depends on GSC
select SERIAL_CORE
default y
---help---
Saying Y here will enable the hardware MUX serial driver for
the Nova, K class systems and D class with a 'remote control card'.
The hardware MUX is not 8250/16550 compatible therefore the
/dev/ttyB0 device is shared between the Serial MUX and the PDC
software console. The following steps need to be completed to use
the Serial MUX:
1. create the device entry (mknod /dev/ttyB0 c 11 0)
2. Edit the /etc/inittab to start a getty listening on /dev/ttyB0
3. Add device ttyB0 to /etc/securetty (if you want to log on as
root on this console.)
4. Change the kernel command console parameter to: console=ttyB0
config SERIAL_MUX_CONSOLE
bool "Support for console on serial MUX"
depends on SERIAL_MUX=y
select SERIAL_CORE_CONSOLE
default y
config PDC_CONSOLE
bool "PDC software console support"
depends on PARISC && !SERIAL_MUX && VT
default n
help
Saying Y here will enable the software based PDC console to be
used as the system console. This is useful for machines in
which the hardware based console has not been written yet. The
following steps must be competed to use the PDC console:
1. create the device entry (mknod /dev/ttyB0 c 11 0)
2. Edit the /etc/inittab to start a getty listening on /dev/ttyB0
3. Add device ttyB0 to /etc/securetty (if you want to log on as
root on this console.)
4. Change the kernel command console parameter to: console=ttyB0
config SERIAL_SUNSAB
tristate "Sun Siemens SAB82532 serial support"
depends on SPARC && PCI
help
This driver supports the Siemens SAB82532 DUSCC serial ports on newer
(PCI) UltraSPARC systems. Say Y or M if you want to be able to these
serial ports.
config SERIAL_SUNSAB_CONSOLE
bool "Console on Sun Siemens SAB82532 serial port"
depends on SERIAL_SUNSAB=y
help
If you would like to be able to use the SAB82532 serial port
on your Sparc system as the console, you can do so by answering
Y to this option.
config SERIAL_SUNHV
bool "Sun4v Hypervisor Console support"
depends on SPARC64
help
This driver supports the console device found on SUN4V Sparc
systems. Say Y if you want to be able to use this device.
config SERIAL_IP22_ZILOG
tristate "SGI Zilog8530 serial support"
depends on SGI_HAS_ZILOG
select SERIAL_CORE
help
This driver supports the Zilog8530 serial ports found on SGI
systems. Say Y or M if you want to be able to these serial ports.
config SERIAL_IP22_ZILOG_CONSOLE
bool "Console on SGI Zilog8530 serial port"
depends on SERIAL_IP22_ZILOG=y
select SERIAL_CORE_CONSOLE
config V850E_UART
bool "NEC V850E on-chip UART support"
depends on V850E_MA1 || V850E_ME2 || V850E_TEG || V850E2_ANNA || V850E_AS85EP1
select SERIAL_CORE
default y
config V850E_UARTB
bool
depends on V850E_UART && V850E_ME2
default y
config V850E_UART_CONSOLE
bool "Use NEC V850E on-chip UART for console"
depends on V850E_UART
select SERIAL_CORE_CONSOLE
config SERIAL_SH_SCI
tristate "SuperH SCI(F) serial port support"
depends on SUPERH || H8300
select SERIAL_CORE
config SERIAL_SH_SCI_NR_UARTS
int "Maximum number of SCI(F) serial ports"
depends on SERIAL_SH_SCI
default "2"
config SERIAL_SH_SCI_CONSOLE
bool "Support for console on SuperH SCI(F)"
depends on SERIAL_SH_SCI=y
select SERIAL_CORE_CONSOLE
config SERIAL_PNX8XXX
bool "Enable PNX8XXX SoCs' UART Support"
depends on MIPS && SOC_PNX8550
select SERIAL_CORE
help
If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
and you want to use serial ports, say Y. Otherwise, say N.
config SERIAL_PNX8XXX_CONSOLE
bool "Enable PNX8XX0 serial console"
depends on SERIAL_PNX8XXX
select SERIAL_CORE_CONSOLE
help
If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
and you want to use serial console, say Y. Otherwise, say N.
config SERIAL_CORE
tristate
config SERIAL_CORE_CONSOLE
bool
config CONSOLE_POLL
bool
config SERIAL_68328
bool "68328 serial support"
depends on M68328 || M68EZ328 || M68VZ328
help
This driver supports the built-in serial port of the Motorola 68328
(standard, EZ and VZ varieties).
config SERIAL_68328_RTS_CTS
bool "Support RTS/CTS on 68328 serial port"
depends on SERIAL_68328
config SERIAL_COLDFIRE
bool "ColdFire serial support (DEPRECATED)"
depends on COLDFIRE
help
This driver supports the built-in serial ports of the Motorola ColdFire
family of CPUs.
This driver is deprecated because it supports only the old interface
for serial drivers and features like magic keys are not working.
Please switch to the new style driver because this driver will be
removed soon.
config SERIAL_MCF
bool "Coldfire serial support (new style driver)"
depends on COLDFIRE
select SERIAL_CORE
help
This new serial driver supports the Freescale Coldfire serial ports
using the new serial driver subsystem.
config SERIAL_MCF_BAUDRATE
int "Default baudrate for Coldfire serial ports"
depends on SERIAL_MCF
default 19200
help
This setting lets you define what the default baudrate is for the
ColdFire serial ports. The usual default varies from board to board,
and this setting is a way of catering for that.
config SERIAL_MCF_CONSOLE
bool "Coldfire serial console support"
depends on SERIAL_MCF
select SERIAL_CORE_CONSOLE
help
Enable a ColdFire internal serial port to be the system console.
config SERIAL_68360_SMC
bool "68360 SMC uart support"
depends on M68360
help
This driver supports the SMC serial ports of the Motorola 68360 CPU.
config SERIAL_68360_SCC
bool "68360 SCC uart support"
depends on M68360
help
This driver supports the SCC serial ports of the Motorola 68360 CPU.
config SERIAL_68360
bool
depends on SERIAL_68360_SMC || SERIAL_68360_SCC
default y
config SERIAL_PMACZILOG
tristate "PowerMac z85c30 ESCC support"
depends on PPC_OF && PPC_PMAC
select SERIAL_CORE
help
This driver supports the Zilog z85C30 serial ports found on
PowerMac machines.
Say Y or M if you want to be able to these serial ports.
config SERIAL_PMACZILOG_TTYS
bool "Use ttySn device nodes for Zilog z85c30"
depends on SERIAL_PMACZILOG
help
The pmac_zilog driver for the z85C30 chip on many powermacs
historically used the device numbers for /dev/ttySn. The
8250 serial port driver also uses these numbers, which means
the two drivers being unable to coexist; you could not use
both z85C30 and 8250 type ports at the same time.
If this option is not selected, the pmac_zilog driver will
use the device numbers allocated for /dev/ttyPZn. This allows
the pmac_zilog and 8250 drivers to co-exist, but may cause
existing userspace setups to break. Programs that need to
access the built-in serial ports on powermacs will need to
be reconfigured to use /dev/ttyPZn instead of /dev/ttySn.
If you enable this option, any z85c30 ports in the system will
be registered as ttyS0 onwards as in the past, and you will be
unable to use the 8250 module for PCMCIA or other 16C550-style
UARTs.
Say N unless you need the z85c30 ports on your powermac
to appear as /dev/ttySn.
config SERIAL_PMACZILOG_CONSOLE
bool "Console on PowerMac z85c30 serial port"
depends on SERIAL_PMACZILOG=y
select SERIAL_CORE_CONSOLE
help
If you would like to be able to use the z85c30 serial port
on your PowerMac as the console, you can do so by answering
Y to this option.
config SERIAL_LH7A40X
tristate "Sharp LH7A40X embedded UART support"
depends on ARM && ARCH_LH7A40X
select SERIAL_CORE
help
This enables support for the three on-board UARTs of the
Sharp LH7A40X series CPUs. Choose Y or M.
config SERIAL_LH7A40X_CONSOLE
bool "Support for console on Sharp LH7A40X serial port"
depends on SERIAL_LH7A40X=y
select SERIAL_CORE_CONSOLE
help
Say Y here if you wish to use one of the serial ports as the
system console--the system console is the device which
receives all kernel messages and warnings and which allows
logins in single user mode.
Even if you say Y here, the currently visible framebuffer console
(/dev/tty0) will still be used as the default system console, but
you can alter that using a kernel command line, for example
"console=ttyAM1".
config SERIAL_CPM
tristate "CPM SCC/SMC serial port support"
depends on CPM2 || 8xx
select SERIAL_CORE
help
This driver supports the SCC and SMC serial ports on Motorola
embedded PowerPC that contain a CPM1 (8xx) or CPM2 (8xxx)
config SERIAL_CPM_CONSOLE
bool "Support for console on CPM SCC/SMC serial port"
depends on SERIAL_CPM=y
select SERIAL_CORE_CONSOLE
help
Say Y here if you wish to use a SCC or SMC CPM UART as the system
console (the system console is the device which receives all kernel
messages and warnings and which allows logins in single user mode).
Even if you say Y here, the currently visible framebuffer console
(/dev/tty0) will still be used as the system console by default, but
you can alter that using a kernel command line option such as
"console=ttyCPM0". (Try "man bootparam" or see the documentation of
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
config SERIAL_CPM_SCC1
bool "Support for SCC1 serial port"
depends on SERIAL_CPM=y
help
Select this option to use SCC1 as a serial port
config SERIAL_CPM_SCC2
bool "Support for SCC2 serial port"
depends on SERIAL_CPM=y
help
Select this option to use SCC2 as a serial port
config SERIAL_CPM_SCC3
bool "Support for SCC3 serial port"
depends on SERIAL_CPM=y
help
Select this option to use SCC3 as a serial port
config SERIAL_CPM_SCC4
bool "Support for SCC4 serial port"
depends on SERIAL_CPM=y
help
Select this option to use SCC4 as a serial port
config SERIAL_CPM_SMC1
bool "Support for SMC1 serial port"
depends on SERIAL_CPM=y
help
Select this option to use SMC1 as a serial port
config SERIAL_CPM_SMC2
bool "Support for SMC2 serial port"
depends on SERIAL_CPM=y
help
Select this option to use SMC2 as a serial port
config SERIAL_SGI_L1_CONSOLE
bool "SGI Altix L1 serial console support"
depends on IA64_GENERIC || IA64_SGI_SN2
select SERIAL_CORE
select SERIAL_CORE_CONSOLE
help
If you have an SGI Altix and you would like to use the system
controller serial port as your console (you want this!),
say Y. Otherwise, say N.
config SERIAL_MPC52xx
tristate "Freescale MPC52xx/MPC512x family PSC serial support"
depends on PPC_MPC52xx || PPC_MPC512x
select SERIAL_CORE
help
This driver supports MPC52xx and MPC512x PSC serial ports. If you would
like to use them, you must answer Y or M to this option. Note that
for use as console, it must be included in kernel and not as a
module.
config SERIAL_MPC52xx_CONSOLE
bool "Console on a Freescale MPC52xx/MPC512x family PSC serial port"
depends on SERIAL_MPC52xx=y
select SERIAL_CORE_CONSOLE
help
Select this options if you'd like to use one of the PSC serial port
of the Freescale MPC52xx family as a console.
config SERIAL_MPC52xx_CONSOLE_BAUD
int "Freescale MPC52xx/MPC512x family PSC serial port baud"
depends on SERIAL_MPC52xx_CONSOLE=y
default "9600"
help
Select the MPC52xx console baud rate.
This value is only used if the bootloader doesn't pass in the
console baudrate
config SERIAL_ICOM
tristate "IBM Multiport Serial Adapter"
depends on PCI && (PPC_ISERIES || PPC_PSERIES)
select SERIAL_CORE
select FW_LOADER
help
This driver is for a family of multiport serial adapters
including 2 port RVX, 2 port internal modem, 4 port internal
modem and a split 1 port RVX and 1 port internal modem.
This driver can also be built as a module. If so, the module
will be called icom.
config SERIAL_M32R_SIO
bool "M32R SIO I/F"
depends on M32R
default y
select SERIAL_CORE
help
Say Y here if you want to use the M32R serial controller.
config SERIAL_M32R_SIO_CONSOLE
bool "use SIO console"
depends on SERIAL_M32R_SIO=y
select SERIAL_CORE_CONSOLE
help
Say Y here if you want to support a serial console.
If you use an M3T-M32700UT or an OPSPUT platform,
please say also y for SERIAL_M32R_PLDSIO.
config SERIAL_M32R_PLDSIO
bool "M32R SIO I/F on a PLD"
depends on SERIAL_M32R_SIO=y && (PLAT_OPSPUT || PLAT_USRV || PLAT_M32700UT)
default n
help
Say Y here if you want to use the M32R serial controller
on a PLD (Programmable Logic Device).
If you use an M3T-M32700UT or an OPSPUT platform,
please say Y.
config SERIAL_TXX9
bool "TMPTX39XX/49XX SIO support"
depends on HAS_TXX9_SERIAL
select SERIAL_CORE
default y
config HAS_TXX9_SERIAL
bool
config SERIAL_TXX9_NR_UARTS
int "Maximum number of TMPTX39XX/49XX SIO ports"
depends on SERIAL_TXX9
default "6"
config SERIAL_TXX9_CONSOLE
bool "TMPTX39XX/49XX SIO Console support"
depends on SERIAL_TXX9=y
select SERIAL_CORE_CONSOLE
config SERIAL_TXX9_STDSERIAL
bool "TX39XX/49XX SIO act as standard serial"
depends on !SERIAL_8250 && SERIAL_TXX9
config SERIAL_VR41XX
tristate "NEC VR4100 series Serial Interface Unit support"
depends on CPU_VR41XX
select SERIAL_CORE
help
If you have a NEC VR4100 series processor and you want to use
Serial Interface Unit(SIU) or Debug Serial Interface Unit(DSIU)
(not include VR4111/VR4121 DSIU), say Y. Otherwise, say N.
config SERIAL_VR41XX_CONSOLE
bool "Enable NEC VR4100 series Serial Interface Unit console"
depends on SERIAL_VR41XX=y
select SERIAL_CORE_CONSOLE
help
If you have a NEC VR4100 series processor and you want to use
a console on a serial port, say Y. Otherwise, say N.
config SERIAL_JSM
tristate "Digi International NEO PCI Support"
depends on PCI
select SERIAL_CORE
help
This is a driver for Digi International's Neo series
of cards which provide multiple serial ports. You would need
something like this to connect more than two modems to your Linux
box, for instance in order to become a dial-in server. This driver
supports PCI boards only.
If you have a card like this, say Y here, otherwise say N.
To compile this driver as a module, choose M here: the
module will be called jsm.
config SERIAL_SGI_IOC4
tristate "SGI IOC4 controller serial support"
depends on (IA64_GENERIC || IA64_SGI_SN2) && SGI_IOC4
select SERIAL_CORE
help
If you have an SGI Altix with an IOC4 based Base IO card
and wish to use the serial ports on this card, say Y.
Otherwise, say N.
config SERIAL_SGI_IOC3
tristate "SGI Altix IOC3 serial support"
depends on (IA64_GENERIC || IA64_SGI_SN2) && SGI_IOC3
select SERIAL_CORE
help
If you have an SGI Altix with an IOC3 serial card,
say Y or M. Otherwise, say N.
config SERIAL_NETX
bool "NetX serial port support"
depends on ARM && ARCH_NETX
select SERIAL_CORE
help
If you have a machine based on a Hilscher NetX SoC you
can enable its onboard serial port by enabling this option.
To compile this driver as a module, choose M here: the
module will be called netx-serial.
config SERIAL_NETX_CONSOLE
bool "Console on NetX serial port"
depends on SERIAL_NETX
select SERIAL_CORE_CONSOLE
help
If you have enabled the serial port on the Hilscher NetX SoC
you can make it the console by answering Y to this option.
config SERIAL_OF_PLATFORM
tristate "Serial port on Open Firmware platform bus"
depends on PPC_OF
depends on SERIAL_8250
help
If you have a PowerPC based system that has serial ports
on a platform specific bus, you should enable this option.
Currently, only 8250 compatible ports are supported, but
others can easily be added.
config SERIAL_QE
tristate "Freescale QUICC Engine serial port support"
depends on QUICC_ENGINE
select SERIAL_CORE
select FW_LOADER
default n
help
This driver supports the QE serial ports on Freescale embedded
PowerPC that contain a QUICC Engine.
config SERIAL_SC26XX
tristate "SC2681/SC2692 serial port support"
depends on SNI_RM
select SERIAL_CORE
help
This is a driver for the onboard serial ports of
older RM400 machines.
config SERIAL_SC26XX_CONSOLE
bool "Console on SC2681/SC2692 serial port"
depends on SERIAL_SC26XX
select SERIAL_CORE_CONSOLE
help
Support for Console on SC2681/SC2692 serial ports.
config SERIAL_BFIN_SPORT
tristate "Blackfin SPORT emulate UART (EXPERIMENTAL)"
depends on BLACKFIN && EXPERIMENTAL
select SERIAL_CORE
help
Enble support SPORT emulate UART on Blackfin series.
To compile this driver as a module, choose M here: the
module will be called bfin_sport_uart.
choice
prompt "Baud rate for Blackfin SPORT UART"
depends on SERIAL_BFIN_SPORT
default SERIAL_SPORT_BAUD_RATE_57600
help
Choose a baud rate for the SPORT UART, other uart settings are
8 bit, 1 stop bit, no parity, no flow control.
config SERIAL_SPORT_BAUD_RATE_115200
bool "115200"
config SERIAL_SPORT_BAUD_RATE_57600
bool "57600"
config SERIAL_SPORT_BAUD_RATE_38400
bool "38400"
config SERIAL_SPORT_BAUD_RATE_19200
bool "19200"
config SERIAL_SPORT_BAUD_RATE_9600
bool "9600"
endchoice
config SPORT_BAUD_RATE
int
depends on SERIAL_BFIN_SPORT
default 115200 if (SERIAL_SPORT_BAUD_RATE_115200)
default 57600 if (SERIAL_SPORT_BAUD_RATE_57600)
default 38400 if (SERIAL_SPORT_BAUD_RATE_38400)
default 19200 if (SERIAL_SPORT_BAUD_RATE_19200)
default 9600 if (SERIAL_SPORT_BAUD_RATE_9600)
endmenu
