/*
* Definitions for RTL818x hardware
*
* Copyright 2007 Michael Wu <flamingice@sourmilk.net>
* Copyright 2007 Andrea Merello <andreamrl@tiscali.it>
*
* Based on the r8187 driver, which is:
* Copyright 2005 Andrea Merello <andreamrl@tiscali.it>, et al.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#ifndef RTL818X_H
#define RTL818X_H
struct rtl818x_csr {
u8 MAC[6];
u8 reserved_0[2];
__le32 MAR[2];
u8 RX_FIFO_COUNT;
u8 reserved_1;
u8 TX_FIFO_COUNT;
u8 BQREQ;
u8 reserved_2[4];
__le32 TSFT[2];
__le32 TLPDA;
__le32 TNPDA;
__le32 THPDA;
__le16 BRSR;
u8 BSSID[6];
u8 RESP_RATE;
u8 EIFS;
u8 reserved_3[1];
u8 CMD;
#define RTL818X_CMD_TX_ENABLE (1 << 2)
#define RTL818X_CMD_RX_ENABLE (1 << 3)
#define RTL818X_CMD_RESET (1 << 4)
u8 reserved_4[4];
__le16 INT_MASK;
__le16 INT_STATUS;
#define RTL818X_INT_RX_OK (1 << 0)
#define RTL818X_INT_RX_ERR (1 << 1)
#define RTL818X_INT_TXL_OK (1 << 2)
#define RTL818X_INT_TXL_ERR (1 << 3)
#define RTL818X_INT_RX_DU (1 << 4)
#define RTL818X_INT_RX_FO (1 << 5)
#define RTL818X_INT_TXN_OK (1 << 6)
#define RTL818X_INT_TXN_ERR (1 << 7)
#define RTL818X_INT_TXH_OK (1 << 8)
#define RTL818X_INT_TXH_ERR (1 << 9)
#define RTL818X_INT_TXB_OK (1 << 10)
#define RTL818X_INT_TXB_ERR (1 << 11)
#define RTL818X_INT_ATIM (1 << 12)
#define RTL818X_INT_BEACON (1 << 13)
#define RTL818X_INT_TIME_OUT (1 << 14)
#define RTL818X_INT_TX_FO (1 << 15)
__le32 TX_CONF;
#define RTL818X_TX_CONF_LOOPBACK_MAC (1 << 17)
#define RTL818X_TX_CONF_NO_ICV (1 << 19)
#define RTL818X_TX_CONF_DISCW (1 << 20)
#define RTL818X_TX_CONF_R8180_ABCD (2 << 25)
#define RTL818X_TX_CONF_R8180_F (3 << 25)
#define RTL818X_TX_CONF_R8185_ABC (4 << 25)
#define RTL818X_TX_CONF_R8185_D (5 << 25)
#define RTL818X_TX_CONF_HWVER_MASK (7 << 25)
#define RTL818X_TX_CONF_CW_MIN (1 << 31)
__le32 RX_CONF;
#define RTL818X_RX_CONF_MONITOR (1 << 0)
#define RTL818X_RX_CONF_NICMAC (1 << 1)
#define RTL818X_RX_CONF_MULTICAST (1 << 2)
#define RTL818X_RX_CONF_BROADCAST (1 << 3)
#define RTL818X_RX_CONF_DATA (1 << 18)
#define RTL818X_RX_CONF_CTRL (1 << 19)
#define RTL818X_RX_CONF_MGMT (1 << 20)
#define RTL818X_RX_CONF_BSSID (1 << 23)
#define RTL818X_RX_CONF_RX_AUTORESETPHY (1 << 28)
#define RTL818X_RX_CONF_ONLYERLPKT (1 << 31)
__le32 INT_TIMEOUT;
__le32 TBDA;
u8 EEPROM_CMD;
#define RTL818X_EEPROM_CMD_READ (1 << 0)
#define RTL818X_EEPROM_CMD_WRITE (1 << 1)
#define RTL818X_EEPROM_CMD_CK (1 << 2)
#define RTL818X_EEPROM_CMD_CS (1 << 3)
#define RTL818X_EEPROM_CMD_NORMAL (0 << 6)
#define RTL818X_EEPROM_CMD_LOAD (1 << 6)
#define RTL818X_EEPROM_CMD_PROGRAM (2 << 6)
#define RTL818X_EEPROM_CMD_CONFIG (3 << 6)
u8 CONFIG0;
u8 CONFIG1;
u8 CONFIG2;
__le32 ANAPARAM;
u8 MSR;
#define RTL818X_MSR_NO_LINK (0 << 2)
#define RTL818X_MSR_ADHOC (1 << 2)
#define RTL818X_MSR_INFRA (2 << 2)
u8 CONFIG3;
#define RTL818X_CONFIG3_ANAPARAM_WRITE (1 << 6)
u8 CONFIG4;
#define RTL818X_CONFIG4_POWEROFF (1 << 6)
#define RTL818X_CONFIG4_VCOOFF (1 << 7)
u8 TESTR;
u8 reserved_9[2];
__le16 PGSELECT;
__le32 ANAPARAM2;
u8 reserved_10[12];
__le16 BEACON_INTERVAL;
__le16 ATIM_WND;
__le16 BEACON_INTERVAL_TIME;
__le16 ATIMTR_INTERVAL;
u8 reserved_11[4];
u8 PHY[4];
__le16 RFPinsOutput;
__le16 RFPinsEnable;
__le16 RFPinsSelect;
__le16 RFPinsInput;
__le32 RF_PARA;
__le32 RF_TIMING;
u8 GP_ENABLE;
u8 GPIO;
u8 reserved_12[10];
u8 TX_AGC_CTL;
#define RTL818X_TX_AGC_CTL_PERPACKET_GAIN_SHIFT (1 << 0)
#define RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT (1 << 1)
#define RTL818X_TX_AGC_CTL_FEEDBACK_ANT (1 << 2)
u8 TX_GAIN_CCK;
u8 TX_GAIN_OFDM;
u8 TX_ANTENNA;
u8 reserved_13[16];
u8 WPA_CONF;
u8 reserved_14[3];
u8 SIFS;
u8 DIFS;
u8 SLOT;
u8 reserved_15[5];
u8 CW_CONF;
#define RTL818X_CW_CONF_PERPACKET_CW_SHIFT (1 << 0)
#define RTL818X_CW_CONF_PERPACKET_RETRY_SHIFT (1 << 1)
u8 CW_VAL;
u8 RATE_FALLBACK;
u8 reserved_16[25];
u8 CONFIG5;
u8 TX_DMA_POLLING;
u8 reserved_17[2];
__le16 CWR;
u8 RETRY_CTR;
u8 reserved_18[5];
__le32 RDSAR;
u8 reserved_19[18];
u16 TALLY_CNT;
u8 TALLY_SEL;
} __attribute__((packed));
static const struct ieee80211_rate rtl818x_rates[] = {
{ .rate = 10,
.val = 0,
.flags = IEEE80211_RATE_CCK },
{ .rate = 20,
.val = 1,
.flags = IEEE80211_RATE_CCK },
{ .rate = 55,
.val = 2,
.flags = IEEE80211_RATE_CCK },
{ .rate = 110,
.val = 3,
.flags = IEEE80211_RATE_CCK },
{ .rate = 60,
.val = 4,
.flags = IEEE80211_RATE_OFDM },
{ .rate = 90,
.val = 5,
.flags = IEEE80211_RATE_OFDM },
{ .rate = 120,
.val = 6,
.flags = IEEE80211_RATE_OFDM },
{ .rate = 180,
.val = 7,
.flags = IEEE80211_RATE_OFDM },
{ .rate = 240,
.val = 8,
.flags = IEEE80211_RATE_OFDM },
{ .rate = 360,
.val = 9,
.flags = IEEE80211_RATE_OFDM },
{ .rate = 480,
.val = 10,
.flags = IEEE80211_RATE_OFDM },
{ .rate = 540,
.val = 11,
.flags = IEEE80211_RATE_OFDM },
};
static const struct ieee80211_channel rtl818x_channels[] = {
{ .chan = 1,
.freq = 2412},
{ .chan = 2,
.freq = 2417},
{ .chan = 3,
.freq = 2422},
{ .chan = 4,
.freq = 2427},
{ .chan = 5,
.freq = 2432},
{ .chan = 6,
.freq = 2437},
{ .chan = 7,
.freq = 2442},
{ .chan = 8,
.freq = 2447},
{ .chan = 9,
.freq = 2452},
{ .chan = 10,
.freq = 2457},
{ .chan = 11,
.freq = 2462},
{ .chan = 12,
.freq = 2467},
{ .chan = 13,
.freq = 2472},
{ .chan = 14,
.freq = 2484}
};
#endif /* RTL818X_H */
