#
# Sensor device configuration
#
menu "I2C Hardware Bus support"
comment "PC SMBus host controller drivers"
depends on PCI
config I2C_ALI1535
tristate "ALI 1535"
depends on PCI
help
If you say yes to this option, support will be included for the SMB
Host controller on Acer Labs Inc. (ALI) M1535 South Bridges. The SMB
controller is part of the 7101 device, which is an ACPI-compliant
Power Management Unit (PMU).
This driver can also be built as a module. If so, the module
will be called i2c-ali1535.
config I2C_ALI1563
tristate "ALI 1563"
depends on PCI && EXPERIMENTAL
help
If you say yes to this option, support will be included for the SMB
Host controller on Acer Labs Inc. (ALI) M1563 South Bridges. The SMB
controller is part of the 7101 device, which is an ACPI-compliant
Power Management Unit (PMU).
This driver can also be built as a module. If so, the module
will be called i2c-ali1563.
config I2C_ALI15X3
tristate "ALI 15x3"
depends on PCI
help
If you say yes to this option, support will be included for the
Acer Labs Inc. (ALI) M1514 and M1543 motherboard I2C interfaces.
This driver can also be built as a module. If so, the module
will be called i2c-ali15x3.
config I2C_AMD756
tristate "AMD 756/766/768/8111 and nVidia nForce"
depends on PCI
help
If you say yes to this option, support will be included for the AMD
756/766/768 mainboard I2C interfaces. The driver also includes
support for the first (SMBus 1.0) I2C interface of the AMD 8111 and
the nVidia nForce I2C interface.
This driver can also be built as a module. If so, the module
will be called i2c-amd756.
config I2C_AMD756_S4882
tristate "SMBus multiplexing on the Tyan S4882"
depends on I2C_AMD756 && X86 && EXPERIMENTAL
help
Enabling this option will add specific SMBus support for the Tyan
S4882 motherboard. On this 4-CPU board, the SMBus is multiplexed
over 8 different channels, where the various memory module EEPROMs
and temperature sensors live. Saying yes here will give you access
to these in addition to the trunk.
This driver can also be built as a module. If so, the module
will be called i2c-amd756-s4882.
config I2C_AMD8111
tristate "AMD 8111"
depends on PCI
help
If you say yes to this option, support will be included for the
second (SMBus 2.0) AMD 8111 mainboard I2C interface.
This driver can also be built as a module. If so, the module
will be called i2c-amd8111.
config I2C_I801
tristate "Intel 82801 (ICH/PCH)"
depends on PCI
help
If you say yes to this option, support will be included for the Intel
801 family of mainboard I2C interfaces. Specifically, the following
versions of the chipset are supported:
82801AA
82801AB
82801BA
82801CA/CAM
82801DB
82801EB/ER (ICH5/ICH5R)
6300ESB
ICH6
ICH7
ESB2
ICH8
ICH9
EP80579 (Tolapai)
ICH10
5/3400 Series (PCH)
Cougar Point (PCH)
Patsburg (PCH)
This driver can also be built as a module. If so, the module
will be called i2c-i801.
config I2C_ISCH
tristate "Intel SCH SMBus 1.0"
depends on PCI
select MFD_CORE
select LPC_SCH
help
Say Y here if you want to use SMBus controller on the Intel SCH
based systems.
This driver can also be built as a module. If so, the module
will be called i2c-isch.
config I2C_PIIX4
tristate "Intel PIIX4 and compatible (ATI/AMD/Serverworks/Broadcom/SMSC)"
depends on PCI
help
If you say yes to this option, support will be included for the Intel
PIIX4 family of mainboard I2C interfaces. Specifically, the following
versions of the chipset are supported (note that Serverworks is part
of Broadcom):
Intel PIIX4
Intel 440MX
ATI IXP200
ATI IXP300
ATI IXP400
ATI SB600
ATI SB700
ATI SB800
AMD Hudson-2
Serverworks OSB4
Serverworks CSB5
Serverworks CSB6
Serverworks HT-1000
Serverworks HT-1100
SMSC Victory66
This driver can also be built as a module. If so, the module
will be called i2c-piix4.
config I2C_NFORCE2
tristate "Nvidia nForce2, nForce3 and nForce4"
depends on PCI
help
If you say yes to this option, support will be included for the Nvidia
nForce2, nForce3 and nForce4 families of mainboard I2C interfaces.
This driver can also be built as a module. If so, the module
will be called i2c-nforce2.
config I2C_NFORCE2_S4985
tristate "SMBus multiplexing on the Tyan S4985"
depends on I2C_NFORCE2 && X86 && EXPERIMENTAL
help
Enabling this option will add specific SMBus support for the Tyan
S4985 motherboard. On this 4-CPU board, the SMBus is multiplexed
over 4 different channels, where the various memory module EEPROMs
live. Saying yes here will give you access to these in addition
to the trunk.
This driver can also be built as a module. If so, the module
will be called i2c-nforce2-s4985.
config I2C_SIS5595
tristate "SiS 5595"
depends on PCI
help
If you say yes to this option, support will be included for the
SiS5595 SMBus (a subset of I2C) interface.
This driver can also be built as a module. If so, the module
will be called i2c-sis5595.
config I2C_SIS630
tristate "SiS 630/730"
depends on PCI
help
If you say yes to this option, support will be included for the
SiS630 and SiS730 SMBus (a subset of I2C) interface.
This driver can also be built as a module. If so, the module
will be called i2c-sis630.
config I2C_SIS96X
tristate "SiS 96x"
depends on PCI
help
If you say yes to this option, support will be included for the SiS
96x SMBus (a subset of I2C) interfaces. Specifically, the following
chipsets are supported:
645/961
645DX/961
645DX/962
648/961
650/961
735
745
This driver can also be built as a module. If so, the module
will be called i2c-sis96x.
config I2C_VIA
tristate "VIA VT82C586B"
depends on PCI && EXPERIMENTAL
select I2C_ALGOBIT
help
If you say yes to this option, support will be included for the VIA
82C586B I2C interface
This driver can also be built as a module. If so, the module
will be called i2c-via.
config I2C_VIAPRO
tristate "VIA VT82C596/82C686/82xx and CX700/VX8xx"
depends on PCI
help
If you say yes to this option, support will be included for the VIA
VT82C596 and later SMBus interface. Specifically, the following
chipsets are supported:
VT82C596A/B
VT82C686A/B
VT8231
VT8233/A
VT8235
VT8237R/A/S
VT8251
CX700
VX800/VX820
VX855/VX875
This driver can also be built as a module. If so, the module
will be called i2c-viapro.
if ACPI
comment "ACPI drivers"
config I2C_SCMI
tristate "SMBus Control Method Interface"
help
This driver supports the SMBus Control Method Interface. It needs the
BIOS to declare ACPI control methods as described in the SMBus Control
Method Interface specification.
To compile this driver as a module, choose M here:
the module will be called i2c-scmi.
endif # ACPI
comment "Mac SMBus host controller drivers"
depends on PPC_CHRP || PPC_PMAC
config I2C_HYDRA
tristate "CHRP Apple Hydra Mac I/O I2C interface"
depends on PCI && PPC_CHRP && EXPERIMENTAL
select I2C_ALGOBIT
help
This supports the use of the I2C interface in the Apple Hydra Mac
I/O chip on some CHRP machines (e.g. the LongTrail). Say Y if you
have such a machine.
This support is also available as a module. If so, the module
will be called i2c-hydra.
config I2C_POWERMAC
tristate "Powermac I2C interface"
depends on PPC_PMAC
default y
help
This exposes the various PowerMac i2c interfaces to the linux i2c
layer and to userland. It is used by various drivers on the PowerMac
platform, and should generally be enabled.
This support is also available as a module. If so, the module
will be called i2c-powermac.
comment "I2C system bus drivers (mostly embedded / system-on-chip)"
config I2C_AT91
tristate "Atmel AT91 I2C Two-Wire interface (TWI)"
depends on ARCH_AT91 && EXPERIMENTAL && BROKEN
help
This supports the use of the I2C interface on Atmel AT91
processors.
This driver is BROKEN because the controller which it uses
will easily trigger RX overrun and TX underrun errors. Using
low I2C clock rates may partially work around those issues
on some systems. Another serious problem is that there is no
documented way to issue repeated START conditions, as needed
to support combined I2C messages. Use the i2c-gpio driver
unless your system can cope with those limitations.
config I2C_AU1550
tristate "Au1550/Au1200 SMBus interface"
depends on SOC_AU1550 || SOC_AU1200
help
If you say yes to this option, support will be included for the
Au1550 and Au1200 SMBus interface.
This driver can also be built as a module. If so, the module
will be called i2c-au1550.
config I2C_BLACKFIN_TWI
tristate "Blackfin TWI I2C support"
depends on BLACKFIN
depends on !BF561 && !BF531 && !BF532 && !BF533
help
This is the I2C bus driver for Blackfin on-chip TWI interface.
This driver can also be built as a module. If so, the module
will be called i2c-bfin-twi.
config I2C_BLACKFIN_TWI_CLK_KHZ
int "Blackfin TWI I2C clock (kHz)"
depends on I2C_BLACKFIN_TWI
range 21 400
default 50
help
The unit of the TWI clock is kHz.
config I2C_CPM
tristate "Freescale CPM1 or CPM2 (MPC8xx/826x)"
depends on (CPM1 || CPM2) && OF_I2C
help
This supports the use of the I2C interface on Freescale
processors with CPM1 or CPM2.
This driver can also be built as a module. If so, the module
will be called i2c-cpm.
config I2C_DAVINCI
tristate "DaVinci I2C driver"
depends on ARCH_DAVINCI
help
Support for TI DaVinci I2C controller driver.
This driver can also be built as a module. If so, the module
will be called i2c-davinci.
Please note that this driver might be needed to bring up other
devices such as DaVinci NIC.
For details please see http://www.ti.com/davinci
config I2C_DESIGNWARE
tristate "Synopsys DesignWare"
depends on HAVE_CLK
help
If you say yes to this option, support will be included for the
Synopsys DesignWare I2C adapter. Only master mode is supported.
This driver can also be built as a module. If so, the module
will be called i2c-designware.
config I2C_GPIO
tristate "GPIO-based bitbanging I2C"
depends on GENERIC_GPIO
select I2C_ALGOBIT
help
This is a very simple bitbanging I2C driver utilizing the
arch-neutral GPIO API to control the SCL and SDA lines.
config I2C_HIGHLANDER
tristate "Highlander FPGA SMBus interface"
depends on SH_HIGHLANDER
help
If you say yes to this option, support will be included for
the SMBus interface located in the FPGA on various Highlander
boards, particularly the R0P7780LC0011RL and R0P7785LC0011RL
FPGAs. This is wholly unrelated to the SoC I2C.
This driver can also be built as a module. If so, the module
will be called i2c-highlander.
config I2C_IBM_IIC
tristate "IBM PPC 4xx on-chip I2C interface"
depends on 4xx
help
Say Y here if you want to use IIC peripheral found on
embedded IBM PPC 4xx based systems.
This driver can also be built as a module. If so, the module
will be called i2c-ibm_iic.
config I2C_IMX
tristate "IMX I2C interface"
depends on ARCH_MXC
help
Say Y here if you want to use the IIC bus controller on
the Freescale i.MX/MXC processors.
This driver can also be built as a module. If so, the module
will be called i2c-imx.
config I2C_INTEL_MID
tristate "Intel Moorestown/Medfield Platform I2C controller"
depends on PCI
help
Say Y here if you have an Intel Moorestown/Medfield platform I2C
controller.
This support is also available as a module. If so, the module
will be called i2c-intel-mid.
config I2C_IOP3XX
tristate "Intel IOPx3xx and IXP4xx on-chip I2C interface"
depends on ARCH_IOP32X || ARCH_IOP33X || ARCH_IXP4XX || ARCH_IOP13XX
help
Say Y here if you want to use the IIC bus controller on
the Intel IOPx3xx I/O Processors or IXP4xx Network Processors.
This driver can also be built as a module. If so, the module
will be called i2c-iop3xx.
config I2C_IXP2000
tristate "IXP2000 GPIO-Based I2C Interface (DEPRECATED)"
depends on ARCH_IXP2000
select I2C_ALGOBIT
help
Say Y here if you have an Intel IXP2000 (2400, 2800, 2850) based
system and are using GPIO lines for an I2C bus.
This support is also available as a module. If so, the module
will be called i2c-ixp2000.
This driver is deprecated and will be dropped soon. Use i2c-gpio
instead.
config I2C_MPC
tristate "MPC107/824x/85xx/512x/52xx/83xx/86xx"
depends on PPC32
help
If you say yes to this option, support will be included for the
built-in I2C interface on the MPC107, Tsi107, MPC512x, MPC52xx,
MPC8240, MPC8245, MPC83xx, MPC85xx and MPC8641 family processors.
This driver can also be built as a module. If so, the module
will be called i2c-mpc.
config I2C_MV64XXX
tristate "Marvell mv64xxx I2C Controller"
depends on (MV64X60 || PLAT_ORION) && EXPERIMENTAL
help
If you say yes to this option, support will be included for the
built-in I2C interface on the Marvell 64xxx line of host bridges.
This driver can also be built as a module. If so, the module
will be called i2c-mv64xxx.
config I2C_NOMADIK
tristate "ST-Ericsson Nomadik/Ux500 I2C Controller"
depends on PLAT_NOMADIK
help
If you say yes to this option, support will be included for the
I2C interface from ST-Ericsson's Nomadik and Ux500 architectures.
config I2C_NUC900
tristate "NUC900 I2C Driver"
depends on ARCH_W90X900
help
Say Y here to include support for I2C controller in the
Winbond/Nuvoton NUC900 based System-on-Chip devices.
config I2C_OCORES
tristate "OpenCores I2C Controller"
depends on EXPERIMENTAL
help
If you say yes to this option, support will be included for the
OpenCores I2C controller. For details see
http://www.opencores.org/projects.cgi/web/i2c/overview
This driver can also be built as a module. If so, the module
will be called i2c-ocores.
config I2C_OMAP
tristate "OMAP I2C adapter"
depends on ARCH_OMAP
default y if MACH_OMAP_H3 || MACH_OMAP_OSK
help
If you say yes to this option, support will be included for the
I2C interface on the Texas Instruments OMAP1/2 family of processors.
Like OMAP1510/1610/1710/5912 and OMAP242x.
For details see http://www.ti.com/omap.
config I2C_PASEMI
tristate "PA Semi SMBus interface"
depends on PPC_PASEMI && PCI
help
Supports the PA Semi PWRficient on-chip SMBus interfaces.
config I2C_PCA_PLATFORM
tristate "PCA9564/PCA9665 as platform device"
select I2C_ALGOPCA
default n
help
This driver supports a memory mapped Philips PCA9564/PCA9665
parallel bus to I2C bus controller.
This driver can also be built as a module. If so, the module
will be called i2c-pca-platform.
config I2C_PMCMSP
tristate "PMC MSP I2C TWI Controller"
depends on PMC_MSP
help
This driver supports the PMC TWI controller on MSP devices.
This driver can also be built as module. If so, the module
will be called i2c-pmcmsp.
config I2C_PNX
tristate "I2C bus support for Philips PNX and NXP LPC targets"
depends on ARCH_PNX4008 || ARCH_LPC32XX
help
This driver supports the Philips IP3204 I2C IP block master and/or
slave controller
This driver can also be built as a module. If so, the module
will be called i2c-pnx.
config I2C_PXA
tristate "Intel PXA2XX I2C adapter"
depends on ARCH_PXA || ARCH_MMP
help
If you have devices in the PXA I2C bus, say yes to this option.
This driver can also be built as a module. If so, the module
will be called i2c-pxa.
config I2C_PXA_SLAVE
bool "Intel PXA2XX I2C Slave comms support"
depends on I2C_PXA
help
Support I2C slave mode communications on the PXA I2C bus. This
is necessary for systems where the PXA may be a target on the
I2C bus.
config HAVE_S3C2410_I2C
bool
help
This will include I2C support for Samsung SoCs. If you want to
include I2C support for any machine, kindly select this in the
respective Kconfig file.
config I2C_S3C2410
tristate "S3C2410 I2C Driver"
depends on HAVE_S3C2410_I2C
help
Say Y here to include support for I2C controller in the
Samsung SoCs.
config I2C_S6000
tristate "S6000 I2C support"
depends on XTENSA_VARIANT_S6000
help
This driver supports the on chip I2C device on the
S6000 xtensa processor family.
To compile this driver as a module, choose M here. The module
will be called i2c-s6000.
config I2C_SH7760
tristate "Renesas SH7760 I2C Controller"
depends on CPU_SUBTYPE_SH7760
help
This driver supports the 2 I2C interfaces on the Renesas SH7760.
This driver can also be built as a module. If so, the module
will be called i2c-sh7760.
config I2C_SH_MOBILE
tristate "SuperH Mobile I2C Controller"
depends on SUPERH || ARCH_SHMOBILE
help
If you say yes to this option, support will be included for the
built-in I2C interface on the Renesas SH-Mobile processor.
This driver can also be built as a module. If so, the module
will be called i2c-sh_mobile.
config I2C_SIMTEC
tristate "Simtec Generic I2C interface"
select I2C_ALGOBIT
help
If you say yes to this option, support will be included for
the Simtec Generic I2C interface. This driver is for the
simple I2C bus used on newer Simtec products for general
I2C, such as DDC on the Simtec BBD2016A.
This driver can also be built as a module. If so, the module
will be called i2c-simtec.
config I2C_STU300
tristate "ST Microelectronics DDC I2C interface"
depends on MACH_U300
default y if MACH_U300
help
If you say yes to this option, support will be included for the
I2C interface from ST Microelectronics simply called "DDC I2C"
supporting both I2C and DDC, used in e.g. the U300 series
mobile platforms.
This driver can also be built as a module. If so, the module
will be called i2c-stu300.
config I2C_VERSATILE
tristate "ARM Versatile/Realview I2C bus support"
depends on ARCH_VERSATILE || ARCH_REALVIEW || ARCH_VEXPRESS
select I2C_ALGOBIT
help
Say yes if you want to support the I2C serial bus on ARMs Versatile
range of platforms.
This driver can also be built as a module. If so, the module
will be called i2c-versatile.
config I2C_OCTEON
tristate "Cavium OCTEON I2C bus support"
depends on CPU_CAVIUM_OCTEON
help
Say yes if you want to support the I2C serial bus on Cavium
OCTEON SOC.
This driver can also be built as a module. If so, the module
will be called i2c-octeon.
config I2C_XILINX
tristate "Xilinx I2C Controller"
depends on EXPERIMENTAL && HAS_IOMEM
help
If you say yes to this option, support will be included for the
Xilinx I2C controller.
This driver can also be built as a module. If so, the module
will be called xilinx_i2c.
config I2C_EG20T
tristate "PCH I2C of Intel EG20T"
depends on PCI
help
This driver is for PCH(Platform controller Hub) I2C of EG20T which
is an IOH(Input/Output Hub) for x86 embedded processor.
This driver can access PCH I2C bus device.
comment "External I2C/SMBus adapter drivers"
config I2C_PARPORT
tristate "Parallel port adapter"
depends on PARPORT
select I2C_ALGOBIT
select I2C_SMBUS
help
This supports parallel port I2C adapters such as the ones made by
Philips or Velleman, Analog Devices evaluation boards, and more.
Basically any adapter using the parallel port as an I2C bus with
no extra chipset is supported by this driver, or could be.
This driver is a replacement for (and was inspired by) an older
driver named i2c-philips-par. The new driver supports more devices,
and makes it easier to add support for new devices.
An adapter type parameter is now mandatory. Please read the file
Documentation/i2c/busses/i2c-parport for details.
Another driver exists, named i2c-parport-light, which doesn't depend
on the parport driver. This is meant for embedded systems. Don't say
Y here if you intend to say Y or M there.
This support is also available as a module. If so, the module
will be called i2c-parport.
config I2C_PARPORT_LIGHT
tristate "Parallel port adapter (light)"
select I2C_ALGOBIT
select I2C_SMBUS
help
This supports parallel port I2C adapters such as the ones made by
Philips or Velleman, Analog Devices evaluation boards, and more.
Basically any adapter using the parallel port as an I2C bus with
no extra chipset is supported by this driver, or could be.
This driver is a light version of i2c-parport. It doesn't depend
on the parport driver, and uses direct I/O access instead. This
might be preferred on embedded systems where wasting memory for
the clean but heavy parport handling is not an option. The
drawback is a reduced portability and the impossibility to
daisy-chain other parallel port devices.
Don't say Y here if you said Y or M to i2c-parport. Saying M to
both is possible but both modules should not be loaded at the same
time.
This support is also available as a module. If so, the module
will be called i2c-parport-light.
config I2C_TAOS_EVM
tristate "TAOS evaluation module"
depends on EXPERIMENTAL
select SERIO
select SERIO_SERPORT
default n
help
This supports TAOS evaluation modules on serial port. In order to
use this driver, you will need the inputattach tool, which is part
of the input-utils package.
If unsure, say N.
This support is also available as a module. If so, the module
will be called i2c-taos-evm.
config I2C_TINY_USB
tristate "Tiny-USB adapter"
depends on USB
help
If you say yes to this option, support will be included for the
i2c-tiny-usb, a simple do-it-yourself USB to I2C interface. See
http://www.harbaum.org/till/i2c_tiny_usb for hardware details.
This driver can also be built as a module. If so, the module
will be called i2c-tiny-usb.
comment "Other I2C/SMBus bus drivers"
config I2C_ACORN
tristate "Acorn IOC/IOMD I2C bus support"
depends on ARCH_ACORN
default y
select I2C_ALGOBIT
help
Say yes if you want to support the I2C bus on Acorn platforms.
If you don't know, say Y.
config I2C_ELEKTOR
tristate "Elektor ISA card"
depends on ISA && BROKEN_ON_SMP
select I2C_ALGOPCF
help
This supports the PCF8584 ISA bus I2C adapter. Say Y if you own
such an adapter.
This support is also available as a module. If so, the module
will be called i2c-elektor.
config I2C_PCA_ISA
tristate "PCA9564/PCA9665 on an ISA bus"
depends on ISA
select I2C_ALGOPCA
default n
help
This driver supports ISA boards using the Philips PCA9564/PCA9665
parallel bus to I2C bus controller.
This driver can also be built as a module. If so, the module
will be called i2c-pca-isa.
This device is almost undetectable and using this driver on a
system which doesn't have this device will result in long
delays when I2C/SMBus chip drivers are loaded (e.g. at boot
time). If unsure, say N.
config I2C_SIBYTE
tristate "SiByte SMBus interface"
depends on SIBYTE_SB1xxx_SOC
help
Supports the SiByte SOC on-chip I2C interfaces (2 channels).
config I2C_STUB
tristate "I2C/SMBus Test Stub"
depends on EXPERIMENTAL && m
default 'n'
help
This module may be useful to developers of SMBus client drivers,
especially for certain kinds of sensor chips.
If you do build this module, be sure to read the notes and warnings
in <file:Documentation/i2c/i2c-stub>.
If you don't know what to do here, definitely say N.
config SCx200_I2C
tristate "NatSemi SCx200 I2C using GPIO pins (DEPRECATED)"
depends on SCx200_GPIO
select I2C_ALGOBIT
help
Enable the use of two GPIO pins of a SCx200 processor as an I2C bus.
If you don't know what to do here, say N.
This support is also available as a module. If so, the module
will be called scx200_i2c.
This driver is deprecated and will be dropped soon. Use i2c-gpio
(or scx200_acb) instead.
config SCx200_I2C_SCL
int "GPIO pin used for SCL"
depends on SCx200_I2C
default "12"
help
Enter the GPIO pin number used for the SCL signal. This value can
also be specified with a module parameter.
config SCx200_I2C_SDA
int "GPIO pin used for SDA"
depends on SCx200_I2C
default "13"
help
Enter the GPIO pin number used for the SSA signal. This value can
also be specified with a module parameter.
config SCx200_ACB
tristate "Geode ACCESS.bus support"
depends on X86_32 && PCI
help
Enable the use of the ACCESS.bus controllers on the Geode SCx200 and
SC1100 processors and the CS5535 and CS5536 Geode companion devices.
If you don't know what to do here, say N.
This support is also available as a module. If so, the module
will be called scx200_acb.
endmenu
