/*
* ahci.h - Common AHCI SATA definitions and declarations
*
* Maintained by: Jeff Garzik <jgarzik@pobox.com>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
* Copyright 2004-2005 Red Hat, Inc.
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2, or (at your option)
* any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; see the file COPYING. If not, write to
* the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
*
*
* libata documentation is available via 'make {ps|pdf}docs',
* as Documentation/DocBook/libata.*
*
* AHCI hardware documentation:
* http://www.intel.com/technology/serialata/pdf/rev1_0.pdf
* http://www.intel.com/technology/serialata/pdf/rev1_1.pdf
*
*/
#ifndef _AHCI_H
#define _AHCI_H
#include <linux/clk.h>
#include <linux/libata.h>
/* Enclosure Management Control */
#define EM_CTRL_MSG_TYPE 0x000f0000
/* Enclosure Management LED Message Type */
#define EM_MSG_LED_HBA_PORT 0x0000000f
#define EM_MSG_LED_PMP_SLOT 0x0000ff00
#define EM_MSG_LED_VALUE 0xffff0000
#define EM_MSG_LED_VALUE_ACTIVITY 0x00070000
#define EM_MSG_LED_VALUE_OFF 0xfff80000
#define EM_MSG_LED_VALUE_ON 0x00010000
enum {
AHCI_MAX_PORTS = 32,
AHCI_MAX_SG = 168, /* hardware max is 64K */
AHCI_DMA_BOUNDARY = 0xffffffff,
AHCI_MAX_CMDS = 32,
AHCI_CMD_SZ = 32,
AHCI_CMD_SLOT_SZ = AHCI_MAX_CMDS * AHCI_CMD_SZ,
AHCI_RX_FIS_SZ = 256,
AHCI_CMD_TBL_CDB = 0x40,
AHCI_CMD_TBL_HDR_SZ = 0x80,
AHCI_CMD_TBL_SZ = AHCI_CMD_TBL_HDR_SZ + (AHCI_MAX_SG * 16),
AHCI_CMD_TBL_AR_SZ = AHCI_CMD_TBL_SZ * AHCI_MAX_CMDS,
AHCI_PORT_PRIV_DMA_SZ = AHCI_CMD_SLOT_SZ + AHCI_CMD_TBL_AR_SZ +
AHCI_RX_FIS_SZ,
AHCI_PORT_PRIV_FBS_DMA_SZ = AHCI_CMD_SLOT_SZ +
AHCI_CMD_TBL_AR_SZ +
(AHCI_RX_FIS_SZ * 16),
AHCI_IRQ_ON_SG = (1 << 31),
AHCI_CMD_ATAPI = (1 << 5),
AHCI_CMD_WRITE = (1 << 6),
AHCI_CMD_PREFETCH = (1 << 7),
AHCI_CMD_RESET = (1 << 8),
AHCI_CMD_CLR_BUSY = (1 << 10),
RX_FIS_PIO_SETUP = 0x20, /* offset of PIO Setup FIS data */
RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */
RX_FIS_SDB = 0x58, /* offset of SDB FIS data */
RX_FIS_UNK = 0x60, /* offset of Unknown FIS data */
/* global controller registers */
HOST_CAP = 0x00, /* host capabilities */
HOST_CTL = 0x04, /* global host control */
HOST_IRQ_STAT = 0x08, /* interrupt status */
HOST_PORTS_IMPL = 0x0c, /* bitmap of implemented ports */
HOST_VERSION = 0x10, /* AHCI spec. version compliancy */
HOST_EM_LOC = 0x1c, /* Enclosure Management location */
HOST_EM_CTL = 0x20, /* Enclosure Management Control */
HOST_CAP2 = 0x24, /* host capabilities, extended */
/* HOST_CTL bits */
HOST_RESET = (1 << 0), /* reset controller; self-clear */
HOST_IRQ_EN = (1 << 1), /* global IRQ enable */
HOST_AHCI_EN = (1 << 31), /* AHCI enabled */
/* HOST_CAP bits */
HOST_CAP_SXS = (1 << 5), /* Supports External SATA */
HOST_CAP_EMS = (1 << 6), /* Enclosure Management support */
HOST_CAP_CCC = (1 << 7), /* Command Completion Coalescing */
HOST_CAP_PART = (1 << 13), /* Partial state capable */
HOST_CAP_SSC = (1 << 14), /* Slumber state capable */
HOST_CAP_PIO_MULTI = (1 << 15), /* PIO multiple DRQ support */
HOST_CAP_FBS = (1 << 16), /* FIS-based switching support */
HOST_CAP_PMP = (1 << 17), /* Port Multiplier support */
HOST_CAP_ONLY = (1 << 18), /* Supports AHCI mode only */
HOST_CAP_CLO = (1 << 24), /* Command List Override support */
HOST_CAP_LED = (1 << 25), /* Supports activity LED */
HOST_CAP_ALPM = (1 << 26), /* Aggressive Link PM support */
HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */
HOST_CAP_MPS = (1 << 28), /* Mechanical presence switch */
HOST_CAP_SNTF = (1 << 29), /* SNotification register */
HOST_CAP_NCQ = (1 << 30), /* Native Command Queueing */
HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */
/* HOST_CAP2 bits */
HOST_CAP2_BOH = (1 << 0), /* BIOS/OS handoff supported */
HOST_CAP2_NVMHCI = (1 << 1), /* NVMHCI supported */
HOST_CAP2_APST = (1 << 2), /* Automatic partial to slumber */
HOST_CAP2_SDS = (1 << 3), /* Support device sleep */
HOST_CAP2_SADM = (1 << 4), /* Support aggressive DevSlp */
HOST_CAP2_DESO = (1 << 5), /* DevSlp from slumber only */
/* registers for each SATA port */
PORT_LST_ADDR = 0x00, /* command list DMA addr */
PORT_LST_ADDR_HI = 0x04, /* command list DMA addr hi */
PORT_FIS_ADDR = 0x08, /* FIS rx buf addr */
PORT_FIS_ADDR_HI = 0x0c, /* FIS rx buf addr hi */
PORT_IRQ_STAT = 0x10, /* interrupt status */
PORT_IRQ_MASK = 0x14, /* interrupt enable/disable mask */
PORT_CMD = 0x18, /* port command */
PORT_TFDATA = 0x20, /* taskfile data */
PORT_SIG = 0x24, /* device TF signature */
PORT_CMD_ISSUE = 0x38, /* command issue */
PORT_SCR_STAT = 0x28, /* SATA phy register: SStatus */
PORT_SCR_CTL = 0x2c, /* SATA phy register: SControl */
PORT_SCR_ERR = 0x30, /* SATA phy register: SError */
PORT_SCR_ACT = 0x34, /* SATA phy register: SActive */
PORT_SCR_NTF = 0x3c, /* SATA phy register: SNotification */
PORT_FBS = 0x40, /* FIS-based Switching */
PORT_DEVSLP = 0x44, /* device sleep */
/* PORT_IRQ_{STAT,MASK} bits */
PORT_IRQ_COLD_PRES = (1 << 31), /* cold presence detect */
PORT_IRQ_TF_ERR = (1 << 30), /* task file error */
PORT_IRQ_HBUS_ERR = (1 << 29), /* host bus fatal error */
PORT_IRQ_HBUS_DATA_ERR = (1 << 28), /* host bus data error */
PORT_IRQ_IF_ERR = (1 << 27), /* interface fatal error */
PORT_IRQ_IF_NONFATAL = (1 << 26), /* interface non-fatal error */
PORT_IRQ_OVERFLOW = (1 << 24), /* xfer exhausted available S/G */
PORT_IRQ_BAD_PMP = (1 << 23), /* incorrect port multiplier */
PORT_IRQ_PHYRDY = (1 << 22), /* PhyRdy changed */
PORT_IRQ_DEV_ILCK = (1 << 7), /* device interlock */
PORT_IRQ_CONNECT = (1 << 6), /* port connect change status */
PORT_IRQ_SG_DONE = (1 << 5), /* descriptor processed */
PORT_IRQ_UNK_FIS = (1 << 4), /* unknown FIS rx'd */
PORT_IRQ_SDB_FIS = (1 << 3), /* Set Device Bits FIS rx'd */
PORT_IRQ_DMAS_FIS = (1 << 2), /* DMA Setup FIS rx'd */
PORT_IRQ_PIOS_FIS = (1 << 1), /* PIO Setup FIS rx'd */
PORT_IRQ_D2H_REG_FIS = (1 << 0), /* D2H Register FIS rx'd */
PORT_IRQ_FREEZE = PORT_IRQ_HBUS_ERR |
PORT_IRQ_IF_ERR |
PORT_IRQ_CONNECT |
PORT_IRQ_PHYRDY |
PORT_IRQ_UNK_FIS |
PORT_IRQ_BAD_PMP,
PORT_IRQ_ERROR = PORT_IRQ_FREEZE |
PORT_IRQ_TF_ERR |
PORT_IRQ_HBUS_DATA_ERR,
DEF_PORT_IRQ = PORT_IRQ_ERROR | PORT_IRQ_SG_DONE |
PORT_IRQ_SDB_FIS | PORT_IRQ_DMAS_FIS |
PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS,
/* PORT_CMD bits */
PORT_CMD_ASP = (1 << 27), /* Aggressive Slumber/Partial */
PORT_CMD_ALPE = (1 << 26), /* Aggressive Link PM enable */
PORT_CMD_ATAPI = (1 << 24), /* Device is ATAPI */
PORT_CMD_FBSCP = (1 << 22), /* FBS Capable Port */
PORT_CMD_PMP = (1 << 17), /* PMP attached */
PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */
PORT_CMD_FIS_ON = (1 << 14), /* FIS DMA engine running */
PORT_CMD_FIS_RX = (1 << 4), /* Enable FIS receive DMA engine */
PORT_CMD_CLO = (1 << 3), /* Command list override */
PORT_CMD_POWER_ON = (1 << 2), /* Power up device */
PORT_CMD_SPIN_UP = (1 << 1), /* Spin up device */
PORT_CMD_START = (1 << 0), /* Enable port DMA engine */
PORT_CMD_ICC_MASK = (0xf << 28), /* i/f ICC state mask */
PORT_CMD_ICC_ACTIVE = (0x1 << 28), /* Put i/f in active state */
PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */
PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */
/* PORT_FBS bits */
PORT_FBS_DWE_OFFSET = 16, /* FBS device with error offset */
PORT_FBS_ADO_OFFSET = 12, /* FBS active dev optimization offset */
PORT_FBS_DEV_OFFSET = 8, /* FBS device to issue offset */
PORT_FBS_DEV_MASK = (0xf << PORT_FBS_DEV_OFFSET), /* FBS.DEV */
PORT_FBS_SDE = (1 << 2), /* FBS single device error */
PORT_FBS_DEC = (1 << 1), /* FBS device error clear */
PORT_FBS_EN = (1 << 0), /* Enable FBS */
/* PORT_DEVSLP bits */
PORT_DEVSLP_DM_OFFSET = 25, /* DITO multiplier offset */
PORT_DEVSLP_DM_MASK = (0xf << 25), /* DITO multiplier mask */
PORT_DEVSLP_DITO_OFFSET = 15, /* DITO offset */
PORT_DEVSLP_MDAT_OFFSET = 10, /* Minimum assertion time */
PORT_DEVSLP_DETO_OFFSET = 2, /* DevSlp exit timeout */
PORT_DEVSLP_DSP = (1 << 1), /* DevSlp present */
PORT_DEVSLP_ADSE = (1 << 0), /* Aggressive DevSlp enable */
/* hpriv->flags bits */
#define AHCI_HFLAGS(flags) .private_data = (void *)(flags)
AHCI_HFLAG_NO_NCQ = (1 << 0),
AHCI_HFLAG_IGN_IRQ_IF_ERR = (1 << 1), /* ignore IRQ_IF_ERR */
AHCI_HFLAG_IGN_SERR_INTERNAL = (1 << 2), /* ignore SERR_INTERNAL */
AHCI_HFLAG_32BIT_ONLY = (1 << 3), /* force 32bit */
AHCI_HFLAG_MV_PATA = (1 << 4), /* PATA port */
AHCI_HFLAG_NO_MSI = (1 << 5), /* no PCI MSI */
AHCI_HFLAG_NO_PMP = (1 << 6), /* no PMP */
AHCI_HFLAG_SECT255 = (1 << 8), /* max 255 sectors */
AHCI_HFLAG_YES_NCQ = (1 << 9), /* force NCQ cap on */
AHCI_HFLAG_NO_SUSPEND = (1 << 10), /* don't suspend */
AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = (1 << 11), /* treat SRST timeout as
link offline */
AHCI_HFLAG_NO_SNTF = (1 << 12), /* no sntf */
AHCI_HFLAG_NO_FPDMA_AA = (1 << 13), /* no FPDMA AA */
AHCI_HFLAG_YES_FBS = (1 << 14), /* force FBS cap on */
AHCI_HFLAG_DELAY_ENGINE = (1 << 15), /* do not start engine on
port start (wait until
error-handling stage) */
/* ap->flags bits */
AHCI_FLAG_COMMON = ATA_FLAG_SATA | ATA_FLAG_PIO_DMA |
ATA_FLAG_ACPI_SATA | ATA_FLAG_AN,
ICH_MAP = 0x90, /* ICH MAP register */
/* em constants */
EM_MAX_SLOTS = 8,
EM_MAX_RETRY = 5,
/* em_ctl bits */
EM_CTL_RST = (1 << 9), /* Reset */
EM_CTL_TM = (1 << 8), /* Transmit Message */
EM_CTL_MR = (1 << 0), /* Message Received */
EM_CTL_ALHD = (1 << 26), /* Activity LED */
EM_CTL_XMT = (1 << 25), /* Transmit Only */
EM_CTL_SMB = (1 << 24), /* Single Message Buffer */
EM_CTL_SGPIO = (1 << 19), /* SGPIO messages supported */
EM_CTL_SES = (1 << 18), /* SES-2 messages supported */
EM_CTL_SAFTE = (1 << 17), /* SAF-TE messages supported */
EM_CTL_LED = (1 << 16), /* LED messages supported */
/* em message type */
EM_MSG_TYPE_LED = (1 << 0), /* LED */
EM_MSG_TYPE_SAFTE = (1 << 1), /* SAF-TE */
EM_MSG_TYPE_SES2 = (1 << 2), /* SES-2 */
EM_MSG_TYPE_SGPIO = (1 << 3), /* SGPIO */
};
struct ahci_cmd_hdr {
__le32 opts;
__le32 status;
__le32 tbl_addr;
__le32 tbl_addr_hi;
__le32 reserved[4];
};
struct ahci_sg {
__le32 addr;
__le32 addr_hi;
__le32 reserved;
__le32 flags_size;
};
struct ahci_em_priv {
enum sw_activity blink_policy;
struct timer_list timer;
unsigned long saved_activity;
unsigned long activity;
unsigned long led_state;
};
struct ahci_port_priv {
struct ata_link *active_link;
struct ahci_cmd_hdr *cmd_slot;
dma_addr_t cmd_slot_dma;
void *cmd_tbl;
dma_addr_t cmd_tbl_dma;
void *rx_fis;
dma_addr_t rx_fis_dma;
/* for NCQ spurious interrupt analysis */
unsigned int ncq_saw_d2h:1;
unsigned int ncq_saw_dmas:1;
unsigned int ncq_saw_sdb:1;
u32 intr_mask; /* interrupts to enable */
bool fbs_supported; /* set iff FBS is supported */
bool fbs_enabled; /* set iff FBS is enabled */
int fbs_last_dev; /* save FBS.DEV of last FIS */
/* enclosure management info per PM slot */
struct ahci_em_priv em_priv[EM_MAX_SLOTS];
};
struct ahci_host_priv {
void __iomem * mmio; /* bus-independent mem map */
unsigned int flags; /* AHCI_HFLAG_* */
u32 cap; /* cap to use */
u32 cap2; /* cap2 to use */
u32 port_map; /* port map to use */
u32 saved_cap; /* saved initial cap */
u32 saved_cap2; /* saved initial cap2 */
u32 saved_port_map; /* saved initial port_map */
u32 em_loc; /* enclosure management location */
u32 em_buf_sz; /* EM buffer size in byte */
u32 em_msg_type; /* EM message type */
struct clk *clk; /* Only for platforms supporting clk */
};
extern int ahci_ignore_sss;
extern struct device_attribute *ahci_shost_attrs[];
extern struct device_attribute *ahci_sdev_attrs[];
#define AHCI_SHT(drv_name) \
ATA_NCQ_SHT(drv_name), \
.can_queue = AHCI_MAX_CMDS - 1, \
.sg_tablesize = AHCI_MAX_SG, \
.dma_boundary = AHCI_DMA_BOUNDARY, \
.shost_attrs = ahci_shost_attrs, \
.sdev_attrs = ahci_sdev_attrs
extern struct ata_port_operations ahci_ops;
extern struct ata_port_operations ahci_pmp_retry_srst_ops;
unsigned int ahci_dev_classify(struct ata_port *ap);
void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag,
u32 opts);
void ahci_save_initial_config(struct device *dev,
struct ahci_host_priv *hpriv,
unsigned int force_port_map,
unsigned int mask_port_map);
void ahci_init_controller(struct ata_host *host);
int ahci_reset_controller(struct ata_host *host);
int ahci_do_softreset(struct ata_link *link, unsigned int *class,
int pmp, unsigned long deadline,
int (*check_ready)(struct ata_link *link));
int ahci_stop_engine(struct ata_port *ap);
void ahci_start_engine(struct ata_port *ap);
int ahci_check_ready(struct ata_link *link);
int ahci_kick_engine(struct ata_port *ap);
int ahci_port_resume(struct ata_port *ap);
void ahci_set_em_messages(struct ahci_host_priv *hpriv,
struct ata_port_info *pi);
int ahci_reset_em(struct ata_host *host);
irqreturn_t ahci_interrupt(int irq, void *dev_instance);
void ahci_print_info(struct ata_host *host, const char *scc_s);
static inline void __iomem *__ahci_port_base(struct ata_host *host,
unsigned int port_no)
{
struct ahci_host_priv *hpriv = host->private_data;
void __iomem *mmio = hpriv->mmio;
return mmio + 0x100 + (port_no * 0x80);
}
static inline void __iomem *ahci_port_base(struct ata_port *ap)
{
return __ahci_port_base(ap->host, ap->port_no);
}
static inline int ahci_nr_ports(u32 cap)
{
return (cap & 0x1f) + 1;
}
#endif /* _AHCI_H */
