/*
* Carsten Langgaard, carstenl@mips.com
* Copyright (C) 1999, 2000 MIPS Technologies, Inc. All rights reserved.
*
* This program is free software; you can distribute it and/or modify it
* under the terms of the GNU General Public License (Version 2) as
* published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
*
* Interrupt exception dispatch code.
*/
#include <linux/config.h>
#include <asm/asm.h>
#include <asm/mipsregs.h>
#include <asm/regdef.h>
#include <asm/stackframe.h>
/* A lot of complication here is taken away because:
*
* 1) We handle one interrupt and return, sitting in a loop and moving across
* all the pending IRQ bits in the cause register is _NOT_ the answer, the
* common case is one pending IRQ so optimize in that direction.
*
* 2) We need not check against bits in the status register IRQ mask, that
* would make this routine slow as hell.
*
* 3) Linux only thinks in terms of all IRQs on or all IRQs off, nothing in
* between like BSD spl() brain-damage.
*
* Furthermore, the IRQs on the MIPS board look basically (barring software
* IRQs which we don't use at all and all external interrupt sources are
* combined together on hardware interrupt 0 (MIPS IRQ 2)) like:
*
* MIPS IRQ Source
* -------- ------
* 0 Software (ignored)
* 1 Software (ignored)
* 2 Combined hardware interrupt (hw0)
* 3 Hardware (ignored)
* 4 Hardware (ignored)
* 5 Hardware (ignored)
* 6 Hardware (ignored)
* 7 R4k timer (what we use)
*
* Note: On the SEAD board thing are a little bit different.
* Here IRQ 2 (hw0) is wired to the UART0 and IRQ 3 (hw1) is wired
* wired to UART1.
*
* We handle the IRQ according to _our_ priority which is:
*
* Highest ---- R4k Timer
* Lowest ---- Combined hardware interrupt
*
* then we just return, if multiple IRQs are pending then we will just take
* another exception, big deal.
*/
.text
.set noreorder
.set noat
.align 5
NESTED(mipsIRQ, PT_SIZE, sp)
SAVE_ALL
CLI
.set at
mfc0 s0, CP0_CAUSE # get irq bits
mfc0 s1, CP0_STATUS # get irq mask
and s0, s1
/* First we check for r4k counter/timer IRQ. */
andi a0, s0, CAUSEF_IP7
beq a0, zero, 1f
andi a0, s0, CAUSEF_IP2 # delay slot, check hw0 interrupt
/* Wheee, a timer interrupt. */
move a0, sp
jal mips_timer_interrupt
nop
j ret_from_irq
nop
1:
#if defined(CONFIG_MIPS_SEAD)
beq a0, zero, 1f
andi a0, s0, CAUSEF_IP3 # delay slot, check hw1 interrupt
#else
beq a0, zero, 1f # delay slot, check hw3 interrupt
andi a0, s0, CAUSEF_IP5
#endif
/* Wheee, combined hardware level zero interrupt. */
#if defined(CONFIG_MIPS_ATLAS)
jal atlas_hw0_irqdispatch
#elif defined(CONFIG_MIPS_MALTA)
jal malta_hw0_irqdispatch
#elif defined(CONFIG_MIPS_SEAD)
jal sead_hw0_irqdispatch
#else
#error "MIPS board not supported\n"
#endif
move a0, sp # delay slot
j ret_from_irq
nop # delay slot
1:
#if defined(CONFIG_MIPS_SEAD)
beq a0, zero, 1f
andi a0, s0, CAUSEF_IP5 # delay slot, check hw3 interrupt
jal sead_hw1_irqdispatch
move a0, sp # delay slot
j ret_from_irq
nop # delay slot
1:
#endif
#if defined(CONFIG_MIPS_MALTA)
beq a0, zero, 1f # check hw3 (coreHI) interrupt
nop
jal corehi_irqdispatch
move a0, sp
j ret_from_irq
nop
1:
#endif
/*
* Here by mistake? This is possible, what can happen is that by the
* time we take the exception the IRQ pin goes low, so just leave if
* this is the case.
*/
move a1,s0
PRINT("Got interrupt: c0_cause = %08x\n")
mfc0 a1, CP0_EPC
PRINT("c0_epc = %08x\n")
j ret_from_irq
nop
END(mipsIRQ)
