/*
* Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH,
* <armlinux@phytec.de>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version 2
* of the License, or (at your option) any later version.
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
#ifndef __MACH_IOMUX_V3_H__
#define __MACH_IOMUX_V3_H__
/*
* build IOMUX_PAD structure
*
* This iomux scheme is based around pads, which are the physical balls
* on the processor.
*
* - Each pad has a pad control register (IOMUXC_SW_PAD_CTRL_x) which controls
* things like driving strength and pullup/pulldown.
* - Each pad can have but not necessarily does have an output routing register
* (IOMUXC_SW_MUX_CTL_PAD_x).
* - Each pad can have but not necessarily does have an input routing register
* (IOMUXC_x_SELECT_INPUT)
*
* The three register sets do not have a fixed offset to each other,
* hence we order this table by pad control registers (which all pads
* have) and put the optional i/o routing registers into additional
* fields.
*
* The naming convention for the pad modes is MX35_PAD_<padname>__<padmode>
* If <padname> or <padmode> refers to a GPIO, it is named
* GPIO_<unit>_<num>
*
*/
struct pad_desc {
unsigned mux_ctrl_ofs:12; /* IOMUXC_SW_MUX_CTL_PAD offset */
unsigned mux_mode:8;
unsigned pad_ctrl_ofs:12; /* IOMUXC_SW_PAD_CTRL offset */
#define NO_PAD_CTRL (1 << 16)
unsigned pad_ctrl:17;
unsigned select_input_ofs:12; /* IOMUXC_SELECT_INPUT offset */
unsigned select_input:3;
};
#define IOMUX_PAD(_pad_ctrl_ofs, _mux_ctrl_ofs, _mux_mode, _select_input_ofs, \
_select_input, _pad_ctrl) \
{ \
.mux_ctrl_ofs = _mux_ctrl_ofs, \
.mux_mode = _mux_mode, \
.pad_ctrl_ofs = _pad_ctrl_ofs, \
.pad_ctrl = _pad_ctrl, \
.select_input_ofs = _select_input_ofs, \
.select_input = _select_input, \
}
/*
* Use to set PAD control
*/
#define PAD_CTL_DVS (1 << 13)
#define PAD_CTL_HYS (1 << 8)
#define PAD_CTL_PKE (1 << 7)
#define PAD_CTL_PUE (1 << 6)
#define PAD_CTL_PUS_100K_DOWN (0 << 4)
#define PAD_CTL_PUS_47K_UP (1 << 4)
#define PAD_CTL_PUS_100K_UP (2 << 4)
#define PAD_CTL_PUS_22K_UP (3 << 4)
#define PAD_CTL_ODE (1 << 3)
#define PAD_CTL_DSE_LOW (0 << 1)
#define PAD_CTL_DSE_MED (1 << 1)
#define PAD_CTL_DSE_HIGH (2 << 1)
#define PAD_CTL_DSE_MAX (3 << 1)
#define PAD_CTL_SRE_FAST (1 << 0)
#define PAD_CTL_SRE_SLOW (0 << 0)
#define MX51_NUM_GPIO_PORT 4
#define GPIO_PIN_MASK 0x1f
#define GPIO_PORT_SHIFT 5
#define GPIO_PORT_MASK (0x7 << GPIO_PORT_SHIFT)
#define GPIO_PORTA (0 << GPIO_PORT_SHIFT)
#define GPIO_PORTB (1 << GPIO_PORT_SHIFT)
#define GPIO_PORTC (2 << GPIO_PORT_SHIFT)
#define GPIO_PORTD (3 << GPIO_PORT_SHIFT)
#define GPIO_PORTE (4 << GPIO_PORT_SHIFT)
#define GPIO_PORTF (5 << GPIO_PORT_SHIFT)
/*
* setups a single pad in the iomuxer
*/
int mxc_iomux_v3_setup_pad(struct pad_desc *pad);
/*
* setups mutliple pads
* convenient way to call the above function with tables
*/
int mxc_iomux_v3_setup_multiple_pads(struct pad_desc *pad_list, unsigned count);
/*
* Initialise the iomux controller
*/
void mxc_iomux_v3_init(void __iomem *iomux_v3_base);
#endif /* __MACH_IOMUX_V3_H__*/
