/*
* Copyright (C) ST-Ericsson SA 2010
*
* Author: Hanumath Prasad <hanumath.prasad@stericsson.com>
* License terms: GNU General Public License (GPL) version 2
*/
#include <linux/kernel.h>
#include <linux/gpio.h>
#include <linux/amba/bus.h>
#include <linux/amba/mmci.h>
#include <linux/mmc/host.h>
#include <linux/platform_device.h>
#include <asm/mach-types.h>
#include <plat/ste_dma40.h>
#include <mach/devices.h>
#include <mach/hardware.h>
#include "devices-db8500.h"
#include "board-mop500.h"
#include "ste-dma40-db8500.h"
/*
* SDI 0 (MicroSD slot)
*/
/* MMCIPOWER bits */
#define MCI_DATA2DIREN (1 << 2)
#define MCI_CMDDIREN (1 << 3)
#define MCI_DATA0DIREN (1 << 4)
#define MCI_DATA31DIREN (1 << 5)
#define MCI_FBCLKEN (1 << 7)
/* GPIO pins used by the sdi0 level shifter */
static int sdi0_en = -1;
static int sdi0_vsel = -1;
static u32 mop500_sdi0_vdd_handler(struct device *dev, unsigned int vdd,
unsigned char power_mode)
{
switch (power_mode) {
case MMC_POWER_UP:
case MMC_POWER_ON:
/*
* Level shifter voltage should depend on vdd to when deciding
* on either 1.8V or 2.9V. Once the decision has been made the
* level shifter must be disabled and re-enabled with a changed
* select signal in order to switch the voltage. Since there is
* no framework support yet for indicating 1.8V in vdd, use the
* default 2.9V.
*/
gpio_direction_output(sdi0_vsel, 0);
gpio_direction_output(sdi0_en, 1);
break;
case MMC_POWER_OFF:
gpio_direction_output(sdi0_vsel, 0);
gpio_direction_output(sdi0_en, 0);
break;
}
return MCI_FBCLKEN | MCI_CMDDIREN | MCI_DATA0DIREN |
MCI_DATA2DIREN | MCI_DATA31DIREN;
}
#ifdef CONFIG_STE_DMA40
struct stedma40_chan_cfg mop500_sdi0_dma_cfg_rx = {
.mode = STEDMA40_MODE_LOGICAL,
.dir = STEDMA40_PERIPH_TO_MEM,
.src_dev_type = DB8500_DMA_DEV29_SD_MM0_RX,
.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
.src_info.data_width = STEDMA40_WORD_WIDTH,
.dst_info.data_width = STEDMA40_WORD_WIDTH,
};
static struct stedma40_chan_cfg mop500_sdi0_dma_cfg_tx = {
.mode = STEDMA40_MODE_LOGICAL,
.dir = STEDMA40_MEM_TO_PERIPH,
.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
.dst_dev_type = DB8500_DMA_DEV29_SD_MM0_TX,
.src_info.data_width = STEDMA40_WORD_WIDTH,
.dst_info.data_width = STEDMA40_WORD_WIDTH,
};
#endif
static struct mmci_platform_data mop500_sdi0_data = {
.vdd_handler = mop500_sdi0_vdd_handler,
.ocr_mask = MMC_VDD_29_30,
.f_max = 50000000,
.capabilities = MMC_CAP_4_BIT_DATA |
MMC_CAP_SD_HIGHSPEED |
MMC_CAP_MMC_HIGHSPEED,
.gpio_wp = -1,
#ifdef CONFIG_STE_DMA40
.dma_filter = stedma40_filter,
.dma_rx_param = &mop500_sdi0_dma_cfg_rx,
.dma_tx_param = &mop500_sdi0_dma_cfg_tx,
#endif
};
static void sdi0_configure(void)
{
int ret;
ret = gpio_request(sdi0_en, "level shifter enable");
if (!ret)
ret = gpio_request(sdi0_vsel,
"level shifter 1v8-3v select");
if (ret) {
pr_warning("unable to config sdi0 gpios for level shifter.\n");
return;
}
/* Select the default 2.9V and enable level shifter */
gpio_direction_output(sdi0_vsel, 0);
gpio_direction_output(sdi0_en, 1);
/* Add the device, force v2 to subrevision 1 */
if (cpu_is_u8500v2())
db8500_add_sdi0(&mop500_sdi0_data, 0x10480180);
else
db8500_add_sdi0(&mop500_sdi0_data, 0);
}
void mop500_sdi_tc35892_init(void)
{
mop500_sdi0_data.gpio_cd = GPIO_SDMMC_CD;
sdi0_en = GPIO_SDMMC_EN;
sdi0_vsel = GPIO_SDMMC_1V8_3V_SEL;
sdi0_configure();
}
/*
* SDI 2 (POP eMMC, not on DB8500ed)
*/
#ifdef CONFIG_STE_DMA40
struct stedma40_chan_cfg mop500_sdi2_dma_cfg_rx = {
.mode = STEDMA40_MODE_LOGICAL,
.dir = STEDMA40_PERIPH_TO_MEM,
.src_dev_type = DB8500_DMA_DEV28_SD_MM2_RX,
.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
.src_info.data_width = STEDMA40_WORD_WIDTH,
.dst_info.data_width = STEDMA40_WORD_WIDTH,
};
static struct stedma40_chan_cfg mop500_sdi2_dma_cfg_tx = {
.mode = STEDMA40_MODE_LOGICAL,
.dir = STEDMA40_MEM_TO_PERIPH,
.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
.dst_dev_type = DB8500_DMA_DEV28_SD_MM2_TX,
.src_info.data_width = STEDMA40_WORD_WIDTH,
.dst_info.data_width = STEDMA40_WORD_WIDTH,
};
#endif
static struct mmci_platform_data mop500_sdi2_data = {
.ocr_mask = MMC_VDD_165_195,
.f_max = 50000000,
.capabilities = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
.gpio_cd = -1,
.gpio_wp = -1,
#ifdef CONFIG_STE_DMA40
.dma_filter = stedma40_filter,
.dma_rx_param = &mop500_sdi2_dma_cfg_rx,
.dma_tx_param = &mop500_sdi2_dma_cfg_tx,
#endif
};
/*
* SDI 4 (on-board eMMC)
*/
#ifdef CONFIG_STE_DMA40
struct stedma40_chan_cfg mop500_sdi4_dma_cfg_rx = {
.mode = STEDMA40_MODE_LOGICAL,
.dir = STEDMA40_PERIPH_TO_MEM,
.src_dev_type = DB8500_DMA_DEV42_SD_MM4_RX,
.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
.src_info.data_width = STEDMA40_WORD_WIDTH,
.dst_info.data_width = STEDMA40_WORD_WIDTH,
};
static struct stedma40_chan_cfg mop500_sdi4_dma_cfg_tx = {
.mode = STEDMA40_MODE_LOGICAL,
.dir = STEDMA40_MEM_TO_PERIPH,
.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
.dst_dev_type = DB8500_DMA_DEV42_SD_MM4_TX,
.src_info.data_width = STEDMA40_WORD_WIDTH,
.dst_info.data_width = STEDMA40_WORD_WIDTH,
};
#endif
static struct mmci_platform_data mop500_sdi4_data = {
.ocr_mask = MMC_VDD_29_30,
.f_max = 50000000,
.capabilities = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA |
MMC_CAP_MMC_HIGHSPEED,
.gpio_cd = -1,
.gpio_wp = -1,
#ifdef CONFIG_STE_DMA40
.dma_filter = stedma40_filter,
.dma_rx_param = &mop500_sdi4_dma_cfg_rx,
.dma_tx_param = &mop500_sdi4_dma_cfg_tx,
#endif
};
void __init mop500_sdi_init(void)
{
u32 periphid = 0;
/* v2 has a new version of this block that need to be forced */
if (cpu_is_u8500v2())
periphid = 0x10480180;
/* PoP:ed eMMC on top of DB8500 v1.0 has problems with high speed */
if (!cpu_is_u8500v10())
mop500_sdi2_data.capabilities |= MMC_CAP_MMC_HIGHSPEED;
/* sdi2 on snowball is in ATL_B mode for FSMC (LAN) */
if (!machine_is_snowball())
db8500_add_sdi2(&mop500_sdi2_data, periphid);
/* On-board eMMC */
db8500_add_sdi4(&mop500_sdi4_data, periphid);
if (machine_is_hrefv60() || machine_is_snowball()) {
if (machine_is_hrefv60()) {
mop500_sdi0_data.gpio_cd = HREFV60_SDMMC_CD_GPIO;
sdi0_en = HREFV60_SDMMC_EN_GPIO;
sdi0_vsel = HREFV60_SDMMC_1V8_3V_GPIO;
} else if (machine_is_snowball()) {
mop500_sdi0_data.gpio_cd = SNOWBALL_SDMMC_CD_GPIO;
mop500_sdi0_data.cd_invert = true;
sdi0_en = SNOWBALL_SDMMC_EN_GPIO;
sdi0_vsel = SNOWBALL_SDMMC_1V8_3V_GPIO;
}
sdi0_configure();
}
/*
* On boards with the TC35892 GPIO expander, sdi0 will finally
* be added when the TC35892 initializes and calls
* mop500_sdi_tc35892_init() above.
*/
}
