/*
* Maxtor Shared Storage II Board Setup
*
* Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/pci.h>
#include <linux/irq.h>
#include <linux/mtd/physmap.h>
#include <linux/mv643xx_eth.h>
#include <linux/leds.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/i2c.h>
#include <linux/ata_platform.h>
#include <linux/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
#include <mach/bridge-regs.h>
#include "common.h"
#include "mpp.h"
#define MSS2_NOR_BOOT_BASE 0xff800000
#define MSS2_NOR_BOOT_SIZE SZ_256K
/*****************************************************************************
* Maxtor Shared Storage II Info
****************************************************************************/
/*
* Maxtor Shared Storage II hardware :
* - Marvell 88F5182-A2 C500
* - Marvell 88E1111 Gigabit Ethernet PHY
* - RTC M41T81 (@0x68) on I2C bus
* - 256KB NOR flash
* - 64MB of RAM
*/
/*****************************************************************************
* 256KB NOR Flash on BOOT Device
****************************************************************************/
static struct physmap_flash_data mss2_nor_flash_data = {
.width = 1,
};
static struct resource mss2_nor_flash_resource = {
.flags = IORESOURCE_MEM,
.start = MSS2_NOR_BOOT_BASE,
.end = MSS2_NOR_BOOT_BASE + MSS2_NOR_BOOT_SIZE - 1,
};
static struct platform_device mss2_nor_flash = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &mss2_nor_flash_data,
},
.resource = &mss2_nor_flash_resource,
.num_resources = 1,
};
/****************************************************************************
* PCI setup
****************************************************************************/
static int __init mss2_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
{
int irq;
/*
* Check for devices with hard-wired IRQs.
*/
irq = orion5x_pci_map_irq(dev, slot, pin);
if (irq != -1)
return irq;
return -1;
}
static struct hw_pci mss2_pci __initdata = {
.nr_controllers = 2,
.setup = orion5x_pci_sys_setup,
.scan = orion5x_pci_sys_scan_bus,
.map_irq = mss2_pci_map_irq,
};
static int __init mss2_pci_init(void)
{
if (machine_is_mss2())
pci_common_init(&mss2_pci);
return 0;
}
subsys_initcall(mss2_pci_init);
/*****************************************************************************
* Ethernet
****************************************************************************/
static struct mv643xx_eth_platform_data mss2_eth_data = {
.phy_addr = MV643XX_ETH_PHY_ADDR(8),
};
/*****************************************************************************
* SATA
****************************************************************************/
static struct mv_sata_platform_data mss2_sata_data = {
.n_ports = 2,
};
/*****************************************************************************
* GPIO buttons
****************************************************************************/
#define MSS2_GPIO_KEY_RESET 12
#define MSS2_GPIO_KEY_POWER 11
static struct gpio_keys_button mss2_buttons[] = {
{
.code = KEY_POWER,
.gpio = MSS2_GPIO_KEY_POWER,
.desc = "Power",
.active_low = 1,
}, {
.code = KEY_RESTART,
.gpio = MSS2_GPIO_KEY_RESET,
.desc = "Reset",
.active_low = 1,
},
};
static struct gpio_keys_platform_data mss2_button_data = {
.buttons = mss2_buttons,
.nbuttons = ARRAY_SIZE(mss2_buttons),
};
static struct platform_device mss2_button_device = {
.name = "gpio-keys",
.id = -1,
.dev = {
.platform_data = &mss2_button_data,
},
};
/*****************************************************************************
* RTC m41t81 on I2C bus
****************************************************************************/
#define MSS2_GPIO_RTC_IRQ 3
static struct i2c_board_info __initdata mss2_i2c_rtc = {
I2C_BOARD_INFO("m41t81", 0x68),
};
/*****************************************************************************
* MSS2 power off method
****************************************************************************/
/*
* On the Maxtor Shared Storage II, the shutdown process is the following :
* - Userland modifies U-boot env to tell U-boot to go idle at next boot
* - The board reboots
* - U-boot starts and go into an idle mode until the user press "power"
*/
static void mss2_power_off(void)
{
u32 reg;
/*
* Enable and issue soft reset
*/
reg = readl(RSTOUTn_MASK);
reg |= 1 << 2;
writel(reg, RSTOUTn_MASK);
reg = readl(CPU_SOFT_RESET);
reg |= 1;
writel(reg, CPU_SOFT_RESET);
}
/****************************************************************************
* General Setup
****************************************************************************/
static unsigned int mss2_mpp_modes[] __initdata = {
MPP0_GPIO, /* Power LED */
MPP1_GPIO, /* Error LED */
MPP2_UNUSED,
MPP3_GPIO, /* RTC interrupt */
MPP4_GPIO, /* HDD ind. (Single/Dual)*/
MPP5_GPIO, /* HD0 5V control */
MPP6_GPIO, /* HD0 12V control */
MPP7_GPIO, /* HD1 5V control */
MPP8_GPIO, /* HD1 12V control */
MPP9_UNUSED,
MPP10_GPIO, /* Fan control */
MPP11_GPIO, /* Power button */
MPP12_GPIO, /* Reset button */
MPP13_UNUSED,
MPP14_SATA_LED, /* SATA 0 active */
MPP15_SATA_LED, /* SATA 1 active */
MPP16_UNUSED,
MPP17_UNUSED,
MPP18_UNUSED,
MPP19_UNUSED,
0,
};
static void __init mss2_init(void)
{
/* Setup basic Orion functions. Need to be called early. */
orion5x_init();
orion5x_mpp_conf(mss2_mpp_modes);
/*
* MPP[20] Unused
* MPP[21] PCI clock
* MPP[22] USB 0 over current
* MPP[23] USB 1 over current
*/
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_ehci1_init();
orion5x_eth_init(&mss2_eth_data);
orion5x_i2c_init();
orion5x_sata_init(&mss2_sata_data);
orion5x_uart0_init();
orion5x_xor_init();
mvebu_mbus_add_window("devbus-boot", MSS2_NOR_BOOT_BASE,
MSS2_NOR_BOOT_SIZE);
platform_device_register(&mss2_nor_flash);
platform_device_register(&mss2_button_device);
if (gpio_request(MSS2_GPIO_RTC_IRQ, "rtc") == 0) {
if (gpio_direction_input(MSS2_GPIO_RTC_IRQ) == 0)
mss2_i2c_rtc.irq = gpio_to_irq(MSS2_GPIO_RTC_IRQ);
else
gpio_free(MSS2_GPIO_RTC_IRQ);
}
i2c_register_board_info(0, &mss2_i2c_rtc, 1);
/* register mss2 specific power-off method */
pm_power_off = mss2_power_off;
}
MACHINE_START(MSS2, "Maxtor Shared Storage II")
/* Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com> */
.atag_offset = 0x100,
.init_machine = mss2_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
.init_irq = orion5x_init_irq,
.init_time = orion5x_timer_init,
.fixup = tag_fixup_mem32,
.restart = orion5x_restart,
MACHINE_END
