/*
* linux/arch/arm/mach-omap2/gpmc-smc91x.c
*
* Copyright (C) 2009 Nokia Corporation
* Contact: Tony Lindgren
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/smc91x.h>
#include <plat/board.h>
#include <plat/gpmc.h>
#include <plat/gpmc-smc91x.h>
static struct omap_smc91x_platform_data *gpmc_cfg;
static struct resource gpmc_smc91x_resources[] = {
[0] = {
.flags = IORESOURCE_MEM,
},
[1] = {
.flags = IORESOURCE_IRQ,
},
};
static struct smc91x_platdata gpmc_smc91x_info = {
.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT | SMC91X_IO_SHIFT_0,
.leda = RPC_LED_100_10,
.ledb = RPC_LED_TX_RX,
};
static struct platform_device gpmc_smc91x_device = {
.name = "smc91x",
.id = -1,
.dev = {
.platform_data = &gpmc_smc91x_info,
},
.num_resources = ARRAY_SIZE(gpmc_smc91x_resources),
.resource = gpmc_smc91x_resources,
};
/*
* Set the gpmc timings for smc91c96. The timings are taken
* from the data sheet available at:
* http://www.smsc.com/main/catalog/lan91c96.html
* REVISIT: Level shifters can add at least to the access latency.
*/
static int smc91c96_gpmc_retime(void)
{
struct gpmc_timings t;
const int t3 = 10; /* Figure 12.2 read and 12.4 write */
const int t4_r = 20; /* Figure 12.2 read */
const int t4_w = 5; /* Figure 12.4 write */
const int t5 = 25; /* Figure 12.2 read */
const int t6 = 15; /* Figure 12.2 read */
const int t7 = 5; /* Figure 12.4 write */
const int t8 = 5; /* Figure 12.4 write */
const int t20 = 185; /* Figure 12.2 read and 12.4 write */
u32 l;
memset(&t, 0, sizeof(t));
/* Read timings */
t.cs_on = 0;
t.adv_on = t.cs_on;
t.oe_on = t.adv_on + t3;
t.access = t.oe_on + t5;
t.oe_off = t.access;
t.adv_rd_off = t.oe_off + max(t4_r, t6);
t.cs_rd_off = t.oe_off;
t.rd_cycle = t20 - t.oe_on;
/* Write timings */
t.we_on = t.adv_on + t3;
if (cpu_is_omap34xx() && (gpmc_cfg->flags & GPMC_MUX_ADD_DATA)) {
t.wr_data_mux_bus = t.we_on;
t.we_off = t.wr_data_mux_bus + t7;
} else
t.we_off = t.we_on + t7;
if (cpu_is_omap34xx())
t.wr_access = t.we_off;
t.adv_wr_off = t.we_off + max(t4_w, t8);
t.cs_wr_off = t.we_off + t4_w;
t.wr_cycle = t20 - t.we_on;
l = GPMC_CONFIG1_DEVICESIZE_16;
if (gpmc_cfg->flags & GPMC_MUX_ADD_DATA)
l |= GPMC_CONFIG1_MUXADDDATA;
if (gpmc_cfg->flags & GPMC_READ_MON)
l |= GPMC_CONFIG1_WAIT_READ_MON;
if (gpmc_cfg->flags & GPMC_WRITE_MON)
l |= GPMC_CONFIG1_WAIT_WRITE_MON;
if (gpmc_cfg->wait_pin)
l |= GPMC_CONFIG1_WAIT_PIN_SEL(gpmc_cfg->wait_pin);
gpmc_cs_write_reg(gpmc_cfg->cs, GPMC_CS_CONFIG1, l);
/*
* FIXME: Calculate the address and data bus muxed timings.
* Note that at least adv_rd_off needs to be changed according
* to omap3430 TRM Figure 11-11. Are the sdp boards using the
* FPGA in between smc91x and omap as the timings are different
* from above?
*/
if (gpmc_cfg->flags & GPMC_MUX_ADD_DATA)
return 0;
return gpmc_cs_set_timings(gpmc_cfg->cs, &t);
}
/*
* Initialize smc91x device connected to the GPMC. Note that we
* assume that pin multiplexing is done in the board-*.c file,
* or in the bootloader.
*/
void __init gpmc_smc91x_init(struct omap_smc91x_platform_data *board_data)
{
unsigned long cs_mem_base;
int ret;
gpmc_cfg = board_data;
if (gpmc_cfg->flags & GPMC_TIMINGS_SMC91C96)
gpmc_cfg->retime = smc91c96_gpmc_retime;
if (gpmc_cs_request(gpmc_cfg->cs, SZ_16M, &cs_mem_base) < 0) {
printk(KERN_ERR "Failed to request GPMC mem for smc91x\n");
return;
}
gpmc_smc91x_resources[0].start = cs_mem_base + 0x300;
gpmc_smc91x_resources[0].end = cs_mem_base + 0x30f;
gpmc_smc91x_resources[1].flags |= (gpmc_cfg->flags & IRQF_TRIGGER_MASK);
if (gpmc_cfg->retime) {
ret = gpmc_cfg->retime();
if (ret != 0)
goto free1;
}
if (gpio_request(gpmc_cfg->gpio_irq, "SMC91X irq") < 0)
goto free1;
gpio_direction_input(gpmc_cfg->gpio_irq);
gpmc_smc91x_resources[1].start = gpio_to_irq(gpmc_cfg->gpio_irq);
if (gpmc_cfg->gpio_pwrdwn) {
ret = gpio_request(gpmc_cfg->gpio_pwrdwn, "SMC91X powerdown");
if (ret)
goto free2;
gpio_direction_output(gpmc_cfg->gpio_pwrdwn, 0);
}
if (gpmc_cfg->gpio_reset) {
ret = gpio_request(gpmc_cfg->gpio_reset, "SMC91X reset");
if (ret)
goto free3;
gpio_direction_output(gpmc_cfg->gpio_reset, 0);
gpio_set_value(gpmc_cfg->gpio_reset, 1);
msleep(100);
gpio_set_value(gpmc_cfg->gpio_reset, 0);
}
if (platform_device_register(&gpmc_smc91x_device) < 0) {
printk(KERN_ERR "Unable to register smc91x device\n");
gpio_free(gpmc_cfg->gpio_reset);
goto free3;
}
return;
free3:
if (gpmc_cfg->gpio_pwrdwn)
gpio_free(gpmc_cfg->gpio_pwrdwn);
free2:
gpio_free(gpmc_cfg->gpio_irq);
free1:
gpmc_cs_free(gpmc_cfg->cs);
printk(KERN_ERR "Could not initialize smc91x\n");
}
