/*
* arch/arm/mach-at91/pm.c
* AT91 Power Management
*
* Copyright (C) 2005 David Brownell
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#include <linux/gpio.h>
#include <linux/suspend.h>
#include <linux/sched.h>
#include <linux/proc_fs.h>
#include <linux/interrupt.h>
#include <linux/sysfs.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/clk/at91_pmc.h>
#include <asm/irq.h>
#include <linux/atomic.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
#include <mach/cpu.h>
#include <mach/hardware.h>
#include "at91_aic.h"
#include "generic.h"
#include "pm.h"
#include "gpio.h"
/*
* Show the reason for the previous system reset.
*/
#include "at91_rstc.h"
#include "at91_shdwc.h"
static void (*at91_pm_standby)(void);
static void __init show_reset_status(void)
{
static char reset[] __initdata = "reset";
static char general[] __initdata = "general";
static char wakeup[] __initdata = "wakeup";
static char watchdog[] __initdata = "watchdog";
static char software[] __initdata = "software";
static char user[] __initdata = "user";
static char unknown[] __initdata = "unknown";
static char signal[] __initdata = "signal";
static char rtc[] __initdata = "rtc";
static char rtt[] __initdata = "rtt";
static char restore[] __initdata = "power-restored";
char *reason, *r2 = reset;
u32 reset_type, wake_type;
if (!at91_shdwc_base || !at91_rstc_base)
return;
reset_type = at91_rstc_read(AT91_RSTC_SR) & AT91_RSTC_RSTTYP;
wake_type = at91_shdwc_read(AT91_SHDW_SR);
switch (reset_type) {
case AT91_RSTC_RSTTYP_GENERAL:
reason = general;
break;
case AT91_RSTC_RSTTYP_WAKEUP:
/* board-specific code enabled the wakeup sources */
reason = wakeup;
/* "wakeup signal" */
if (wake_type & AT91_SHDW_WAKEUP0)
r2 = signal;
else {
r2 = reason;
if (wake_type & AT91_SHDW_RTTWK) /* rtt wakeup */
reason = rtt;
else if (wake_type & AT91_SHDW_RTCWK) /* rtc wakeup */
reason = rtc;
else if (wake_type == 0) /* power-restored wakeup */
reason = restore;
else /* unknown wakeup */
reason = unknown;
}
break;
case AT91_RSTC_RSTTYP_WATCHDOG:
reason = watchdog;
break;
case AT91_RSTC_RSTTYP_SOFTWARE:
reason = software;
break;
case AT91_RSTC_RSTTYP_USER:
reason = user;
break;
default:
reason = unknown;
break;
}
pr_info("AT91: Starting after %s %s\n", reason, r2);
}
static int at91_pm_valid_state(suspend_state_t state)
{
switch (state) {
case PM_SUSPEND_ON:
case PM_SUSPEND_STANDBY:
case PM_SUSPEND_MEM:
return 1;
default:
return 0;
}
}
static suspend_state_t target_state;
/*
* Called after processes are frozen, but before we shutdown devices.
*/
static int at91_pm_begin(suspend_state_t state)
{
target_state = state;
return 0;
}
/*
* Verify that all the clocks are correct before entering
* slow-clock mode.
*/
static int at91_pm_verify_clocks(void)
{
unsigned long scsr;
int i;
scsr = at91_pmc_read(AT91_PMC_SCSR);
/* USB must not be using PLLB */
if (cpu_is_at91rm9200()) {
if ((scsr & (AT91RM9200_PMC_UHP | AT91RM9200_PMC_UDP)) != 0) {
pr_err("AT91: PM - Suspend-to-RAM with USB still active\n");
return 0;
}
} else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()
|| cpu_is_at91sam9g20() || cpu_is_at91sam9g10()) {
if ((scsr & (AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP)) != 0) {
pr_err("AT91: PM - Suspend-to-RAM with USB still active\n");
return 0;
}
}
/* PCK0..PCK3 must be disabled, or configured to use clk32k */
for (i = 0; i < 4; i++) {
u32 css;
if ((scsr & (AT91_PMC_PCK0 << i)) == 0)
continue;
css = at91_pmc_read(AT91_PMC_PCKR(i)) & AT91_PMC_CSS;
if (css != AT91_PMC_CSS_SLOW) {
pr_err("AT91: PM - Suspend-to-RAM with PCK%d src %d\n", i, css);
return 0;
}
}
return 1;
}
/*
* Call this from platform driver suspend() to see how deeply to suspend.
* For example, some controllers (like OHCI) need one of the PLL clocks
* in order to act as a wakeup source, and those are not available when
* going into slow clock mode.
*
* REVISIT: generalize as clk_will_be_available(clk)? Other platforms have
* the very same problem (but not using at91 main_clk), and it'd be better
* to add one generic API rather than lots of platform-specific ones.
*/
int at91_suspend_entering_slow_clock(void)
{
return (target_state == PM_SUSPEND_MEM);
}
EXPORT_SYMBOL(at91_suspend_entering_slow_clock);
static void (*slow_clock)(void __iomem *pmc, void __iomem *ramc0,
void __iomem *ramc1, int memctrl);
#ifdef CONFIG_AT91_SLOW_CLOCK
extern void at91_slow_clock(void __iomem *pmc, void __iomem *ramc0,
void __iomem *ramc1, int memctrl);
extern u32 at91_slow_clock_sz;
#endif
static int at91_pm_enter(suspend_state_t state)
{
if (of_have_populated_dt())
at91_pinctrl_gpio_suspend();
else
at91_gpio_suspend();
at91_irq_suspend();
pr_debug("AT91: PM - wake mask %08x, pm state %d\n",
/* remember all the always-wake irqs */
(at91_pmc_read(AT91_PMC_PCSR)
| (1 << AT91_ID_FIQ)
| (1 << AT91_ID_SYS)
| (at91_get_extern_irq()))
& at91_aic_read(AT91_AIC_IMR),
state);
switch (state) {
/*
* Suspend-to-RAM is like STANDBY plus slow clock mode, so
* drivers must suspend more deeply: only the master clock
* controller may be using the main oscillator.
*/
case PM_SUSPEND_MEM:
/*
* Ensure that clocks are in a valid state.
*/
if (!at91_pm_verify_clocks())
goto error;
/*
* Enter slow clock mode by switching over to clk32k and
* turning off the main oscillator; reverse on wakeup.
*/
if (slow_clock) {
int memctrl = AT91_MEMCTRL_SDRAMC;
if (cpu_is_at91rm9200())
memctrl = AT91_MEMCTRL_MC;
else if (cpu_is_at91sam9g45())
memctrl = AT91_MEMCTRL_DDRSDR;
#ifdef CONFIG_AT91_SLOW_CLOCK
/* copy slow_clock handler to SRAM, and call it */
memcpy(slow_clock, at91_slow_clock, at91_slow_clock_sz);
#endif
slow_clock(at91_pmc_base, at91_ramc_base[0],
at91_ramc_base[1], memctrl);
break;
} else {
pr_info("AT91: PM - no slow clock mode enabled ...\n");
/* FALLTHROUGH leaving master clock alone */
}
/*
* STANDBY mode has *all* drivers suspended; ignores irqs not
* marked as 'wakeup' event sources; and reduces DRAM power.
* But otherwise it's identical to PM_SUSPEND_ON: cpu idle, and
* nothing fancy done with main or cpu clocks.
*/
case PM_SUSPEND_STANDBY:
/*
* NOTE: the Wait-for-Interrupt instruction needs to be
* in icache so no SDRAM accesses are needed until the
* wakeup IRQ occurs and self-refresh is terminated.
* For ARM 926 based chips, this requirement is weaker
* as at91sam9 can access a RAM in self-refresh mode.
*/
if (at91_pm_standby)
at91_pm_standby();
break;
case PM_SUSPEND_ON:
cpu_do_idle();
break;
default:
pr_debug("AT91: PM - bogus suspend state %d\n", state);
goto error;
}
pr_debug("AT91: PM - wakeup %08x\n",
at91_aic_read(AT91_AIC_IPR) & at91_aic_read(AT91_AIC_IMR));
error:
target_state = PM_SUSPEND_ON;
at91_irq_resume();
if (of_have_populated_dt())
at91_pinctrl_gpio_resume();
else
at91_gpio_resume();
return 0;
}
/*
* Called right prior to thawing processes.
*/
static void at91_pm_end(void)
{
target_state = PM_SUSPEND_ON;
}
static const struct platform_suspend_ops at91_pm_ops = {
.valid = at91_pm_valid_state,
.begin = at91_pm_begin,
.enter = at91_pm_enter,
.end = at91_pm_end,
};
static struct platform_device at91_cpuidle_device = {
.name = "cpuidle-at91",
};
void at91_pm_set_standby(void (*at91_standby)(void))
{
if (at91_standby) {
at91_cpuidle_device.dev.platform_data = at91_standby;
at91_pm_standby = at91_standby;
}
}
static int __init at91_pm_init(void)
{
#ifdef CONFIG_AT91_SLOW_CLOCK
slow_clock = (void *) (AT91_IO_VIRT_BASE - at91_slow_clock_sz);
#endif
pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow clock mode)" : ""));
/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */
if (cpu_is_at91rm9200())
at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
if (at91_cpuidle_device.dev.platform_data)
platform_device_register(&at91_cpuidle_device);
suspend_set_ops(&at91_pm_ops);
show_reset_status();
return 0;
}
arch_initcall(at91_pm_init);
