aboutsummaryrefslogblamecommitdiffstats
path: root/arch/arm/mach-at91/board-sam9263ek.c
blob: b4cd5d0ed597ed57bbd90460b1e8b8b7797f3d2f (plain) (tree)


























                                                                            
                              
                     

                            

                             











                           
                                  



                    




                                                      







                                                                                   

























                                                                   

































                                                                                     










                                                   









                                                                                                      














                                                      


                                                       
                                        




                            














                                                              
                                                                                   



















                                                        
  




































                                                                               
                                               



                                                          
                                               













                                                                      
















































                                                                         






                                              



















                                                                  
         


  








                                            
                                                                               
                                                                        

                           

                                             

                                           

                                            
                 
                                     

                                            

                                

                                            

                                                     











                                                            
/*
 * linux/arch/arm/mach-at91/board-sam9263ek.c
 *
 *  Copyright (C) 2005 SAN People
 *  Copyright (C) 2007 Atmel Corporation.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 */

#include <linux/types.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/fb.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>

#include <video/atmel_lcdc.h>

#include <asm/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>

#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>

#include <asm/arch/board.h>
#include <asm/arch/gpio.h>
#include <asm/arch/at91sam9_smc.h>

#include "generic.h"


static void __init ek_map_io(void)
{
	/* Initialize processor: 16.367 MHz crystal */
	at91sam9263_initialize(16367660);

	/* DGBU on ttyS0. (Rx & Tx only) */
	at91_register_uart(0, 0, 0);

	/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
	at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);

	/* set serial console to ttyS0 (ie, DBGU) */
	at91_set_serial_console(0);
}

static void __init ek_init_irq(void)
{
	at91sam9263_init_interrupts(NULL);
}


/*
 * USB Host port
 */
static struct at91_usbh_data __initdata ek_usbh_data = {
	.ports		= 2,
	.vbus_pin	= { AT91_PIN_PA24, AT91_PIN_PA21 },
};

/*
 * USB Device port
 */
static struct at91_udc_data __initdata ek_udc_data = {
	.vbus_pin	= AT91_PIN_PA25,
	.pullup_pin	= 0,		/* pull-up driven by UDC */
};


/*
 * ADS7846 Touchscreen
 */
#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
static int ads7843_pendown_state(void)
{
	return !at91_get_gpio_value(AT91_PIN_PA15);	/* Touchscreen PENIRQ */
}

static struct ads7846_platform_data ads_info = {
	.model			= 7843,
	.x_min			= 150,
	.x_max			= 3830,
	.y_min			= 190,
	.y_max			= 3830,
	.vref_delay_usecs	= 100,
	.x_plate_ohms		= 450,
	.y_plate_ohms		= 250,
	.pressure_max		= 15000,
	.debounce_max		= 1,
	.debounce_rep		= 0,
	.debounce_tol		= (~0),
	.get_pendown_state	= ads7843_pendown_state,
};

static void __init ek_add_device_ts(void)
{
	at91_set_B_periph(AT91_PIN_PA15, 1);	/* External IRQ1, with pullup */
	at91_set_gpio_input(AT91_PIN_PA31, 1);	/* Touchscreen BUSY signal */
}
#else
static void __init ek_add_device_ts(void) {}
#endif

/*
 * SPI devices.
 */
static struct spi_board_info ek_spi_devices[] = {
#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
	{	/* DataFlash card */
		.modalias	= "mtd_dataflash",
		.chip_select	= 0,
		.max_speed_hz	= 15 * 1000 * 1000,
		.bus_num	= 0,
	},
#endif
#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
	{
		.modalias	= "ads7846",
		.chip_select	= 3,
		.max_speed_hz	= 125000 * 26,	/* (max sample rate @ 3V) * (cmd + data + overhead) */
		.bus_num	= 0,
		.platform_data	= &ads_info,
		.irq		= AT91SAM9263_ID_IRQ1,
	},
#endif
};


/*
 * MCI (SD/MMC)
 */
static struct at91_mmc_data __initdata ek_mmc_data = {
	.wire4		= 1,
	.det_pin	= AT91_PIN_PE18,
	.wp_pin		= AT91_PIN_PE19,
//	.vcc_pin	= ... not connected
};


/*
 * MACB Ethernet device
 */
static struct at91_eth_data __initdata ek_macb_data = {
	.phy_irq_pin	= AT91_PIN_PE31,
	.is_rmii	= 1,
};


/*
 * NAND flash
 */
static struct mtd_partition __initdata ek_nand_partition[] = {
	{
		.name	= "Partition 1",
		.offset	= 0,
		.size	= 64 * 1024 * 1024,
	},
	{
		.name	= "Partition 2",
		.offset	= 64 * 1024 * 1024,
		.size	= MTDPART_SIZ_FULL,
	},
};

static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
{
	*num_partitions = ARRAY_SIZE(ek_nand_partition);
	return ek_nand_partition;
}

static struct at91_nand_data __initdata ek_nand_data = {
	.ale		= 21,
	.cle		= 22,
//	.det_pin	= ... not connected
	.rdy_pin	= AT91_PIN_PA22,
	.enable_pin	= AT91_PIN_PD15,
	.partition_info	= nand_partitions,
#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
	.bus_width_16	= 1,
#else
	.bus_width_16	= 0,
#endif
};


/*
 * LCD Controller
 */
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
static struct fb_videomode at91_tft_vga_modes[] = {
	{
	        .name           = "TX09D50VM1CCA @ 60",
		.refresh	= 60,
		.xres		= 240,		.yres		= 320,
		.pixclock	= KHZ2PICOS(4965),

		.left_margin	= 1,		.right_margin	= 33,
		.upper_margin	= 1,		.lower_margin	= 0,
		.hsync_len	= 5,		.vsync_len	= 1,

		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
		.vmode		= FB_VMODE_NONINTERLACED,
	},
};

static struct fb_monspecs at91fb_default_monspecs = {
	.manufacturer	= "HIT",
	.monitor        = "TX09D70VM1CCA",

	.modedb		= at91_tft_vga_modes,
	.modedb_len	= ARRAY_SIZE(at91_tft_vga_modes),
	.hfmin		= 15000,
	.hfmax		= 64000,
	.vfmin		= 50,
	.vfmax		= 150,
};

#define AT91SAM9263_DEFAULT_LCDCON2 	(ATMEL_LCDC_MEMOR_LITTLE \
					| ATMEL_LCDC_DISTYPE_TFT    \
					| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)

static void at91_lcdc_power_control(int on)
{
	at91_set_gpio_value(AT91_PIN_PA30, on);
}

/* Driver datas */
static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
	.lcdcon_is_backlight		= true,
	.default_bpp			= 16,
	.default_dmacon			= ATMEL_LCDC_DMAEN,
	.default_lcdcon2		= AT91SAM9263_DEFAULT_LCDCON2,
	.default_monspecs		= &at91fb_default_monspecs,
	.atmel_lcdfb_power_control	= at91_lcdc_power_control,
	.guard_time			= 1,
};

#else
static struct atmel_lcdfb_info __initdata ek_lcdc_data;
#endif


/*
 * GPIO Buttons
 */
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
static struct gpio_keys_button ek_buttons[] = {
	{	/* BP1, "leftclic" */
		.code		= BTN_LEFT,
		.gpio		= AT91_PIN_PC5,
		.active_low	= 1,
		.desc		= "left_click",
		.wakeup		= 1,
	},
	{	/* BP2, "rightclic" */
		.code		= BTN_RIGHT,
		.gpio		= AT91_PIN_PC4,
		.active_low	= 1,
		.desc		= "right_click",
		.wakeup		= 1,
	},
};

static struct gpio_keys_platform_data ek_button_data = {
	.buttons	= ek_buttons,
	.nbuttons	= ARRAY_SIZE(ek_buttons),
};

static struct platform_device ek_button_device = {
	.name		= "gpio-keys",
	.id		= -1,
	.num_resources	= 0,
	.dev		= {
		.platform_data	= &ek_button_data,
	}
};

static void __init ek_add_device_buttons(void)
{
	at91_set_GPIO_periph(AT91_PIN_PC5, 0);	/* left button */
	at91_set_deglitch(AT91_PIN_PC5, 1);
	at91_set_GPIO_periph(AT91_PIN_PC4, 0);	/* right button */
	at91_set_deglitch(AT91_PIN_PC4, 1);

	platform_device_register(&ek_button_device);
}
#else
static void __init ek_add_device_buttons(void) {}
#endif


/*
 * AC97
 */
static struct atmel_ac97_data ek_ac97_data = {
	.reset_pin	= AT91_PIN_PA13,
};


/*
 * LEDs ... these could all be PWM-driven, for variable brightness
 */
static struct gpio_led ek_leds[] = {
	{	/* "left" led, green, userled1, pwm1 */
		.name			= "ds1",
		.gpio			= AT91_PIN_PB8,
		.active_low		= 1,
		.default_trigger	= "mmc0",
	},
	{	/* "right" led, green, userled2, pwm2 */
		.name			= "ds2",
		.gpio			= AT91_PIN_PC29,
		.active_low		= 1,
		.default_trigger	= "nand-disk",
	},
	{	/* "power" led, yellow, pwm0 */
		.name			= "ds3",
		.gpio			= AT91_PIN_PB7,
		.default_trigger	= "heartbeat",
	}
};


static void __init ek_board_init(void)
{
	/* Serial */
	at91_add_device_serial();
	/* USB Host */
	at91_add_device_usbh(&ek_usbh_data);
	/* USB Device */
	at91_add_device_udc(&ek_udc_data);
	/* SPI */
	at91_set_gpio_output(AT91_PIN_PE20, 1);		/* select spi0 clock */
	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
	/* Touchscreen */
	ek_add_device_ts();
	/* MMC */
	at91_add_device_mmc(1, &ek_mmc_data);
	/* Ethernet */
	at91_add_device_eth(&ek_macb_data);
	/* NAND */
	at91_add_device_nand(&ek_nand_data);
	/* I2C */
	at91_add_device_i2c(NULL, 0);
	/* LCD Controller */
	at91_add_device_lcdc(&ek_lcdc_data);
	/* Push Buttons */
	ek_add_device_buttons();
	/* AC97 */
	at91_add_device_ac97(&ek_ac97_data);
	/* LEDs */
	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
}

MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")
	/* Maintainer: Atmel */
	.phys_io	= AT91_BASE_SYS,
	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
	.boot_params	= AT91_SDRAM_BASE + 0x100,
	.timer		= &at91sam926x_timer,
	.map_io		= ek_map_io,
	.init_irq	= ek_init_irq,
	.init_machine	= ek_board_init,
MACHINE_END