/*
* Copyright (C) 2005 SAN People
* Copyright (C) 2008 Atmel
* Copyright (C) 2010 Lee McLoughlin - lee@lmmrtech.com
* Copyright (C) 2010 Sergio Tanzilli - tanzilli@acmesystems.it
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/types.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/at73c213.h>
#include <linux/gpio.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/clk.h>
#include <linux/w1-gpio.h>
#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
#include "generic.h"
/*
* The FOX Board G20 hardware comes as the "Netus G20" board with
* just the cpu, ram, dataflash and two header connectors.
* This is plugged into the FOX Board which provides the ethernet,
* usb, rtc, leds, switch, ...
*
* For more info visit: http://www.acmesystems.it/foxg20
*/
static void __init foxg20_init_early(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
}
/*
* USB Host port
*/
static struct at91_usbh_data __initdata foxg20_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
/*
* USB Device port
*/
static struct at91_udc_data __initdata foxg20_udc_data = {
.vbus_pin = AT91_PIN_PC6,
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
};
/*
* SPI devices.
*/
static struct spi_board_info foxg20_spi_devices[] = {
#if !defined(CONFIG_MMC_AT91)
{
.modalias = "mtd_dataflash",
.chip_select = 1,
.max_speed_hz = 15 * 1000 * 1000,
.bus_num = 0,
},
#endif
};
/*
* MACB Ethernet device
*/
static struct macb_platform_data __initdata foxg20_macb_data = {
.phy_irq_pin = AT91_PIN_PA7,
.is_rmii = 1,
};
/*
* MCI (SD/MMC)
* det_pin, wp_pin and vcc_pin are not connected
*/
static struct at91_mmc_data __initdata foxg20_mmc_data = {
.slot_b = 1,
.wire4 = 1,
.det_pin = -EINVAL,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
/*
* LEDs
*/
static struct gpio_led foxg20_leds[] = {
{ /* user led, red */
.name = "user_led",
.gpio = AT91_PIN_PC7,
.active_low = 0,
.default_trigger = "heartbeat",
},
};
/*
* GPIO Buttons
*/
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
static struct gpio_keys_button foxg20_buttons[] = {
{
.gpio = AT91_PIN_PC4,
.code = BTN_1,
.desc = "Button 1",
.active_low = 1,
.wakeup = 1,
},
};
static struct gpio_keys_platform_data foxg20_button_data = {
.buttons = foxg20_buttons,
.nbuttons = ARRAY_SIZE(foxg20_buttons),
};
static struct platform_device foxg20_button_device = {
.name = "gpio-keys",
.id = -1,
.num_resources = 0,
.dev = {
.platform_data = &foxg20_button_data,
}
};
static void __init foxg20_add_device_buttons(void)
{
at91_set_gpio_input(AT91_PIN_PC4, 1); /* btn1 */
at91_set_deglitch(AT91_PIN_PC4, 1);
platform_device_register(&foxg20_button_device);
}
#else
static void __init foxg20_add_device_buttons(void) {}
#endif
#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
static struct w1_gpio_platform_data w1_gpio_pdata = {
/* If you choose to use a pin other than PB16 it needs to be 3.3V */
.pin = AT91_PIN_PB16,
.is_open_drain = 1,
};
static struct platform_device w1_device = {
.name = "w1-gpio",
.id = -1,
.dev.platform_data = &w1_gpio_pdata,
};
static void __init at91_add_device_w1(void)
{
at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
at91_set_multi_drive(w1_gpio_pdata.pin, 1);
platform_device_register(&w1_device);
}
#endif
static struct i2c_board_info __initdata foxg20_i2c_devices[] = {
{
I2C_BOARD_INFO("24c512", 0x50),
},
};
static void __init foxg20_board_init(void)
{
/* Serial */
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
at91_register_uart(AT91SAM9260_ID_US0, 1,
ATMEL_UART_CTS
| ATMEL_UART_RTS
| ATMEL_UART_DTR
| ATMEL_UART_DSR
| ATMEL_UART_DCD
| ATMEL_UART_RI);
/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9260_ID_US1, 2,
ATMEL_UART_CTS
| ATMEL_UART_RTS);
/* USART2 on ttyS3. (Rx & Tx only) */
at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
/* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9260_ID_US3, 4,
ATMEL_UART_CTS
| ATMEL_UART_RTS);
/* USART4 on ttyS5. (Rx & Tx only) */
at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
/* USART5 on ttyS6. (Rx & Tx only) */
at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
/* Set the internal pull-up resistor on DRXD */
at91_set_A_periph(AT91_PIN_PB14, 1);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&foxg20_usbh_data);
/* USB Device */
at91_add_device_udc(&foxg20_udc_data);
/* SPI */
at91_add_device_spi(foxg20_spi_devices, ARRAY_SIZE(foxg20_spi_devices));
/* Ethernet */
at91_add_device_eth(&foxg20_macb_data);
/* MMC */
at91_add_device_mmc(0, &foxg20_mmc_data);
/* I2C */
at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices));
/* LEDs */
at91_gpio_leds(foxg20_leds, ARRAY_SIZE(foxg20_leds));
/* Push Buttons */
foxg20_add_device_buttons();
#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
at91_add_device_w1();
#endif
}
MACHINE_START(ACMENETUSFOXG20, "Acme Systems srl FOX Board G20")
/* Maintainer: Sergio Tanzilli */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
.init_early = foxg20_init_early,
.init_irq = at91_init_irq_default,
.init_machine = foxg20_board_init,
MACHINE_END
