#include <linux/linkage.h>
#include <linux/threads.h>
#include <asm/asm-offsets.h>
#include <asm/assembler.h>
#include <asm/glue-cache.h>
#include <asm/glue-proc.h>
#include <asm/system.h>
.text
/*
* Save CPU state for a suspend
* r1 = v:p offset
* r2 = suspend function arg0
* r3 = suspend function
*/
ENTRY(__cpu_suspend)
stmfd sp!, {r4 - r11, lr}
#ifdef MULTI_CPU
ldr r10, =processor
ldr r5, [r10, #CPU_SLEEP_SIZE] @ size of CPU sleep state
ldr ip, [r10, #CPU_DO_RESUME] @ virtual resume function
#else
ldr r5, =cpu_suspend_size
ldr ip, =cpu_do_resume
#endif
mov r6, sp @ current virtual SP
sub sp, sp, r5 @ allocate CPU state on stack
mov r0, sp @ save pointer to CPU save block
add ip, ip, r1 @ convert resume fn to phys
stmfd sp!, {r1, r6, ip} @ save v:p, virt SP, phys resume fn
ldr r5, =sleep_save_sp
add r6, sp, r1 @ convert SP to phys
stmfd sp!, {r2, r3} @ save suspend func arg and pointer
#ifdef CONFIG_SMP
ALT_SMP(mrc p15, 0, lr, c0, c0, 5)
ALT_UP(mov lr, #0)
and lr, lr, #15
str r6, [r5, lr, lsl #2] @ save phys SP
#else
str r6, [r5] @ save phys SP
#endif
#ifdef MULTI_CPU
mov lr, pc
ldr pc, [r10, #CPU_DO_SUSPEND] @ save CPU state
#else
bl cpu_do_suspend
#endif
@ flush data cache
#ifdef MULTI_CACHE
ldr r10, =cpu_cache
mov lr, pc
ldr pc, [r10, #CACHE_FLUSH_KERN_ALL]
#else
bl __cpuc_flush_kern_all
#endif
adr lr, BSYM(cpu_suspend_abort)
ldmfd sp!, {r0, pc} @ call suspend fn
ENDPROC(__cpu_suspend)
.ltorg
cpu_suspend_abort:
ldmia sp!, {r1 - r3} @ pop v:p, virt SP, phys resume fn
mov sp, r2
ldmfd sp!, {r4 - r11, pc}
ENDPROC(cpu_suspend_abort)
/*
* r0 = control register value
* r1 = v:p offset (preserved by cpu_do_resume)
* r2 = phys page table base
* r3 = L1 section flags
*/
ENTRY(cpu_resume_mmu)
adr r4, cpu_resume_turn_mmu_on
mov r4, r4, lsr #20
orr r3, r3, r4, lsl #20
ldr r5, [r2, r4, lsl #2] @ save old mapping
str r3, [r2, r4, lsl #2] @ setup 1:1 mapping for mmu code
sub r2, r2, r1
ldr r3, =cpu_resume_after_mmu
bic r1, r0, #CR_C @ ensure D-cache is disabled
b cpu_resume_turn_mmu_on
ENDPROC(cpu_resume_mmu)
.ltorg
.align 5
cpu_resume_turn_mmu_on:
mcr p15, 0, r1, c1, c0, 0 @ turn on MMU, I-cache, etc
mrc p15, 0, r1, c0, c0, 0 @ read id reg
mov r1, r1
mov r1, r1
mov pc, r3 @ jump to virtual address
ENDPROC(cpu_resume_turn_mmu_on)
cpu_resume_after_mmu:
str r5, [r2, r4, lsl #2] @ restore old mapping
mcr p15, 0, r0, c1, c0, 0 @ turn on D-cache
bl cpu_init @ restore the und/abt/irq banked regs
mov r0, #0 @ return zero on success
ldmfd sp!, {r4 - r11, pc}
ENDPROC(cpu_resume_after_mmu)
/*
* Note: Yes, part of the following code is located into the .data section.
* This is to allow sleep_save_sp to be accessed with a relative load
* while we can't rely on any MMU translation. We could have put
* sleep_save_sp in the .text section as well, but some setups might
* insist on it to be truly read-only.
*/
.data
.align
ENTRY(cpu_resume)
#ifdef CONFIG_SMP
adr r0, sleep_save_sp
ALT_SMP(mrc p15, 0, r1, c0, c0, 5)
ALT_UP(mov r1, #0)
and r1, r1, #15
ldr r0, [r0, r1, lsl #2] @ stack phys addr
#else
ldr r0, sleep_save_sp @ stack phys addr
#endif
setmode PSR_I_BIT | PSR_F_BIT | SVC_MODE, r1 @ set SVC, irqs off
@ load v:p, stack, resume fn
ARM( ldmia r0!, {r1, sp, pc} )
THUMB( ldmia r0!, {r1, r2, r3} )
THUMB( mov sp, r2 )
THUMB( bx r3 )
ENDPROC(cpu_resume)
sleep_save_sp:
.rept CONFIG_NR_CPUS
.long 0 @ preserve stack phys ptr here
.endr
