/*
* Support for CompuLab CM-T3517
*/
/dts-v1/;
#include "am3517.dtsi"
#include "omap3-cm-t3x.dtsi"
/ {
model = "CompuLab CM-T3517";
compatible = "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
vmmc: regulator-vmmc {
compatible = "regulator-fixed";
regulator-name = "vmmc";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
wl12xx_vmmc2: wl12xx_vmmc2 {
compatible = "regulator-fixed";
regulator-name = "vw1271";
pinctrl-names = "default";
pinctrl-0 = <
&wl12xx_wkup_pins
&wl12xx_core_pins
>;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
gpio = <&gpio1 6 GPIO_ACTIVE_HIGH >; /* gpio6 */
startup-delay-us = <20000>;
enable-active-high;
};
wl12xx_vaux2: wl12xx_vaux2 {
compatible = "regulator-fixed";
regulator-name = "vwl1271_vaux2";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
};
&omap3_pmx_wkup {
wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins {
pinctrl-single,pins = <
OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */
OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE4) /* sys_boot4.gpio_6 */
>;
};
};
&omap3_pmx_core {
phy1_reset_pins: pinmux_hsusb1_phy_reset_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE4) /* uart2_tx.gpio_146 */
>;
};
phy2_reset_pins: pinmux_hsusb2_phy_reset_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x217a, PIN_OUTPUT | MUX_MODE4) /* uart2_rx.gpio_147 */
>;
};
otg_drv_vbus: pinmux_otg_drv_vbus {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50Mhz_clk.usb0_drvvbus */
>;
};
mmc2_pins: pinmux_mmc2_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
>;
};
wl12xx_core_pins: pinmux_wl12xx_core_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs5.gpio_56 */
OMAP3_CORE1_IOPAD(0x2176, PIN_INPUT_PULLUP | MUX_MODE4) /* uart2_rts.gpio_145 */
>;
};
usb_hub_pins: pinmux_usb_hub_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2184, PIN_OUTPUT | MUX_MODE4) /* mcbsp4_clkx.gpio_152 - USB HUB RST */
>;
};
};
&hsusb1_phy {
pinctrl-names = "default";
pinctrl-0 = <&phy1_reset_pins>;
reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>;
};
&hsusb2_phy {
pinctrl-names = "default";
pinctrl-0 = <&phy2_reset_pins>;
reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>;
};
&davinci_emac {
status = "okay";
};
&davinci_mdio {
status = "okay";
};
&am35x_otg_hs {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&otg_drv_vbus>;
};
&mmc1 {
vmmc-supply = <&vmmc>;
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
vmmc-supply = <&wl12xx_vmmc2>;
vmmc_aux-supply = <&wl12xx_vaux2>;
non-removable;
bus-width = <4>;
cap-power-off-card;
};
&dss {
status = "ok";
pinctrl-names = "default";
pinctrl-0 = <
&dss_dpi_pins_common
&dss_dpi_pins_cm_t35x
>;
};
