|
|
Kernel driver zl6100
====================
Supported chips:
* Intersil / Zilker Labs ZL2004
Prefix: 'zl2004'
Addresses scanned: -
Datasheet: http://www.intersil.com/data/fn/fn6847.pdf
* Intersil / Zilker Labs ZL2005
Prefix: 'zl2005'
Addresses scanned: -
Datasheet: http://www.intersil.com/data/fn/fn6848.pdf
* Intersil / Zilker Labs ZL2006
Prefix: 'zl2006'
Addresses scanned: -
Datasheet: http://www.intersil.com/data/fn/fn6850.pdf
* Intersil / Zilker Labs ZL2008
Prefix: 'zl2008'
Addresses scanned: -
Datasheet: http://www.intersil.com/data/fn/fn6859.pdf
* Intersil / Zilker Labs ZL2105
Prefix: 'zl2105'
Addresses scanned: -
Datasheet: http://www.intersil.com/data/fn/fn6851.pdf
* Intersil / Zilker Labs ZL2106
Prefix: 'zl2106'
Addresses scanned: -
Datasheet: http://www.intersil.com/data/fn/fn6852.pdf
* Intersil / Zilker Labs ZL6100
Prefix: 'zl6100'
Addresses scanned: -
Datasheet: http://www.intersil.com/data/fn/fn6876.pdf
* Intersil / Zilker Labs ZL6105
Prefix: 'zl6105'
Addresses scanned: -
Datasheet: http://www.intersil.com/data/fn/fn6906.pdf
* Intersil / Zilker Labs ZL9101M
Prefix: 'zl9101'
Addresses scanned: -
Datasheet: http://www.intersil.com/data/fn/fn7669.pdf
* Intersil / Zilker Labs ZL9117M
Prefix: 'zl9117'
Addresses scanned: -
Datasheet: http://www.intersil.com/data/fn/fn7914.pdf
* Ericsson BMR450, BMR451
Prefix: 'bmr450', 'bmr451'
Addresses scanned: -
Datasheet:
http://archive.ericsson.net/service/internet/picov/get?DocNo=28701-EN/LZT146401
* Ericsson BMR462, BMR463, BMR464
Prefixes: 'bmr462', 'bmr463', 'bmr464'
Addresses scanned: -
Datasheet:
http://archive.ericsson.net/service/internet/picov/get?DocNo=28701-EN/LZT146256
Author: Guenter Roeck <guenter.roeck@ericsson.com>
Description
-----------
This driver supports hardware montoring for Intersil / Zilker Labs ZL6100 and
compatible digital DC-DC controllers.
The driver is a client driver to the core PMBus driver. Please see
Documentation/hwmon/pmbus and Documentation.hwmon/pmbus-core for details
on PMBus client drivers.
Usage Notes
-----------
This driver does not auto-detect devices. You will have to instantiate the
devices explicitly. Please see Documentation/i2c/instantiating-devices for
details.
WARNING: Do not access chip registers using the i2cdump command, and do not use
any of the i2ctools commands on a command register used to save and restore
configuration data (0x11, 0x12, 0x15, 0x16, and 0xf4). The chips supported by
this driver interpret any access to those command registers (including read
commands) as request to execute the command in question. Unless write accesses
to those registers are protected, this may result in power loss, board resets,
and/or Flash corruption. Worst case, your board may turn into a brick.
Platform data support
---------------------
The driver supports standard PMBus driver platform data.
Module parameters
-----------------
delay
-----
Intersil/Zilker Labs DC-DC controllers require a minimum interval between I2C
bus accesses. According to Intersil, the minimum interval is 2 ms, though 1 ms
appears to be sufficient and has not caused any problems in testing. The problem
is known to affect all currently supported chips. For manual override, the
driver provides a writeable module parameter, 'delay', which can be used to set
the interval to a value between 0 and 65,535 microseconds.
Sysfs entries
-------------
The following attributes are supported. Limits are read-write; all other
attributes are read-only.
in1_label "vin"
in1_input Measured input voltage.
in1_min Minimum input voltage.
in1_max Maximum input voltage.
in1_lcrit Critical minimum input voltage.
in1_crit Critical maximum input voltage.
in1_min_alarm Input voltage low alarm.
in1_max_alarm Input voltage high alarm.
in1_lcrit_alarm Input voltage critical low alarm.
in1_crit_alarm Input voltage critical high alarm.
in2_label "vout1"
in2_input Measured output voltage.
in2_lcrit Critical minimum output Voltage.
in2_crit Critical maximum output voltage.
in2_lcrit_alarm Critical output voltage critical low alarm.
in2_crit_alarm Critical output voltage critical high alarm.
curr1_label "iout1"
curr1_input Measured output current.
curr1_lcrit Critical minimum output current.
curr1_crit Critical maximum output current.
curr1_lcrit_alarm Output current critical low alarm.
curr1_crit_alarm Output current critical high alarm.
temp[12]_input Measured temperature.
temp[12]_min Minimum temperature.
temp[12]_max Maximum temperature.
temp[12]_lcrit Critical low temperature.
temp[12]_crit Critical high temperature.
temp[12]_min_alarm Chip temperature low alarm.
temp[12]_max_alarm Chip temperature high alarm.
temp[12]_lcrit_alarm Chip temperature critical low alarm.
temp[12]_crit_alarm Chip temperature critical high alarm.
|
